search

teodoryantcheff / SolidCam-Mach3-Post

A SolidCam postprocessor for Mach3, supporting 4x and 5x operations
28 stars 24 forks source link

4 axis machine x #13

Closed mwrtis86 closed 4 years ago

mwrtis86 commented 4 years ago

Hi..happy new year..!! Can you tell me please if you have post processor for 4axis machine x..??

teodoryantcheff commented 4 years ago

Hey, happy new year to you too! As far as I remember both the along X and along Y posts are in. Am I wrong?

mwrtis86 commented 4 years ago

Thanks for the answer.. yes it is in old file but along x It doesn't show the displacement of the fourth axis to the code

Στάλθηκε από το iPhone μου

2 Ιαν 2020, 11:49, ο χρήστης «teodoryantcheff notifications@github.com» έγραψε:



Hey, happy new year to you too! As far as I remember both the along X and along Y posts are in. Am I wrong?

— You are receiving this because you authored the thread. Reply to this email directly, view it on GitHubhttps://github.com/teodoryantcheff/SolidCam-Mach3-Post/issues/13?email_source=notifications&email_token=AOFL22ILJZ636XY4HVBRJKLQ3W2BZA5CNFSM4KB5P3CKYY3PNVWWK3TUL52HS4DFVREXG43VMVBW63LNMVXHJKTDN5WW2ZLOORPWSZGOEH57D4A#issuecomment-570159600, or unsubscribehttps://github.com/notifications/unsubscribe-auth/AOFL22IFHLPFALW6R7MNG5DQ3W2BZANCNFSM4KB5P3CA.

teodoryantcheff commented 4 years ago

Well... It's been quite some time now. What I can suggest is to just swap your machine axes ... Or make a mach profile with x and y swapped. That should get you going.

mwrtis86 commented 4 years ago

Are you going to create a post processor for the x;

Στάλθηκε από το iPhone μου

2 Ιαν 2020, 13:04, ο χρήστης «teodoryantcheff notifications@github.com» έγραψε:

Well... It's been quite some time now. What I can suggest is to just swap your machine axes ... Or make a mach profile with x and y swapped. That should get you going.

teodoryantcheff commented 4 years ago

Are you going to create a post processor for the x;

Most likely not. Not anytime soon for sure. Would totally appreciate a PR though.

Cheers,

Teo

biqut2 commented 4 years ago

As far as I know last time I used this post processor it did support both x an y. In any case swapping out two letters is trivial.

teodoryantcheff commented 4 years ago

There was something with a and b axes being the defaults along x and y... angle_4x_around_y and such... Due to my lack of time now, I cannot sit down and play with that -- hence suggesting to @mwrtis86 to just swap his machine axes and go with that.

teodoryantcheff commented 4 years ago

@mwrtis86 Unless you have further questions about that, I'm closing the issue.

teodoryantcheff commented 4 years ago

@biqut2, @mwrtis86 is correct -- I redid the post back in time and now only the Y version is in.

mwrtis86 commented 4 years ago

Ok thank you

Αποκτήστε το Outlook για iOShttps://aka.ms/o0ukef

Από: teodoryantcheff notifications@github.com Στάλθηκε: Monday, January 6, 2020 12:43:07 PM Προς: teodoryantcheff/SolidCam-Mach3-Post SolidCam-Mach3-Post@noreply.github.com Κοιν.: mwrtis86 aslanis_gewrgios@hotmail.gr; Mention mention@noreply.github.com Θέμα: Re: [teodoryantcheff/SolidCam-Mach3-Post] 4 axis machine x (#13)

@biqut2https://github.com/biqut2, @mwrtis86https://github.com/mwrtis86 is correct -- I redid the post back in time and now only the Y version is in.

— You are receiving this because you were mentioned. Reply to this email directly, view it on GitHubhttps://github.com/teodoryantcheff/SolidCam-Mach3-Post/issues/13?email_source=notifications&email_token=AOFL22J5WQLVYPHBMYWPKDDQ4MDLXA5CNFSM4KB5P3CKYY3PNVWWK3TUL52HS4DFVREXG43VMVBW63LNMVXHJKTDN5WW2ZLOORPWSZGOEIFCXGY#issuecomment-571091867, or unsubscribehttps://github.com/notifications/unsubscribe-auth/AOFL22O5ZCGHDYHYOV4Z2ZLQ4MDLXANCNFSM4KB5P3CA.