thamoscorp / minimosd-extra

Automatically exported from code.google.com/p/minimosd-extra
0 stars 0 forks source link

OSD overlay disappear when video glitches on CCD camera #87

Closed GoogleCodeExporter closed 9 years ago

GoogleCodeExporter commented 9 years ago
I'm using come 600tvl camera (can't remember exact model), on boot I can't get 
OSD to display I need to press the reset button on the OSD to get display, when 
I start flying I get some glitches on video (low signal) that will cause my OSD 
overlay to disappear only way to restore it are to press the reset button which 
is impossible as the plane are on air :p

What steps will reproduce the problem?
1. Happen every time video signal lost/glitches
2. Swapped 3 different type of camera same results
3. Changing Mode (from stabilize to loiter) also will make the overlay Disappear
4. It does not happen when the OSD is connected to GoPro/Mobius only CCD camera
5. camera are PAL

I'm using MinimOSD-Extra_Plane_Pre-release_2.4_r719, flashed the OSD using 
Windows 7 64 bit

Thanks

Original issue reported on code.google.com by idzu...@gmail.com on 30 Sep 2014 at 3:43

GoogleCodeExporter commented 9 years ago
Closed as we have a new version.

Ifthe problem is still present please reopen it.

Original comment by gabek...@gmail.com on 28 Nov 2014 at 11:44

GoogleCodeExporter commented 9 years ago
I'm having the same issue with r800.

Original comment by craig.ma...@gmail.com on 2 Dec 2014 at 5:50

GoogleCodeExporter commented 9 years ago
i have same problem
apm 2.6
MinimOSD-Extra_Copter_Pre-release_2.4_r702
when i have low signal or change the motor turn it happen.

Original comment by Ea.educ...@gmail.com on 12 Feb 2015 at 11:28

GoogleCodeExporter commented 9 years ago
Can we reopen this? Same issue here with r800

Original comment by mhor...@googlemail.com on 8 Mar 2015 at 8:56

GoogleCodeExporter commented 9 years ago
Hello

I'v tryed to debug this with hardware - because to software it looks too random.
I'v found that Voltage regulator on V2.0 board really sucks. My first board get 
only 3.9V from it (not working at all- shadows and hazzy OSD), second one 4.5V  
...I'v switched to 5.3V from APM PM with shottky diode with 0.3V drop. Then my 
OSD become rock solid. Check your regulator voltages please

Original comment by kratochv...@gmail.com on 8 Mar 2015 at 9:07

GoogleCodeExporter commented 9 years ago
Hi, I'll do that, thanks. But I don't know where the regulator is located and 
how it does look like... Any hint?

Original comment by mhor...@googlemail.com on 6 Apr 2015 at 7:04

GoogleCodeExporter commented 9 years ago
Have this isuue on all of my 3 OSDs. They all different versions 1.0, 1.1, 2.0. 
All have that. I've tried different schemes of powering them and different 
firmwares (even Rushduino for MultiWii). It does not solves the problem. 
Voltage measurements shows acceptable voltage on MAX7456. Issue appears more 
frequent if board is cooled to near zero or colder temperature. I think the 
problem is not in ATMega. Because there is signal on it's outputs visible with 
oscilloscope. Something happens with MAX7456

Original comment by VYag...@gmail.com on 9 May 2015 at 10:53

GoogleCodeExporter commented 9 years ago
Same problem here. 

I had no problems with arducam-osd. I did not change my setup.

Original comment by sschiman...@gmail.com on 26 May 2015 at 8:55