timvideos HDMI2USB-numato-opsis-hardware issues

timvideos / HDMI2USB-numato-opsis-hardware

The Numato Opsis board is the first fully open source HDMI2USB board.

Creative Commons Attribution Share Alike 4.0 International

106 stars 44 forks source link

issues

Newest

Newest Most commented Recently updated Oldest Least commented Least recently updated

Numato obsoletion notice - any replacements?

#65 nyov opened 2 years ago
1
Link to current Opsis supplier page

#64 paddatrapper closed 6 years ago
0
Memory bandwidth for Opsis

#63 Aregaard closed 6 years ago
1
DP/HDMI(input)--> FPGA (Scaling)--> DP(output)

#62 Aregaard closed 6 years ago
1
PCB cad as a png

#61 CarlFK opened 7 years ago
3
pictures of the Opsis board

#60 CarlFK opened 7 years ago
7
Confused about HDMI resolution

#59 nesteruk closed 7 years ago
8
DIFFCLK_B0P / DIFFCLK_B0N is backwards

#58 mithro opened 8 years ago
0
Replace "PCIe" name in the schematic with "TOFE"

#57 mithro opened 8 years ago
0
DIFFCLK_A1P / DIFFCLK_A1N is backwards

#56 mithro opened 8 years ago
0
Figure out possible back drive issue on HDMI inputs

#55 mithro opened 8 years ago
0
Swap GND and VCC3V3 pins on the SDCard header - P28

#54 mithro opened 8 years ago
0
MAC Address EEPROM is marked differently in schematic / PCB

#53 mithro opened 8 years ago
0
Adding initial set of svg and stl files for front ports.

#52 phlipped closed 8 years ago
1
how to purchase?

#51 CarlFK closed 8 years ago
1
Investigate compatibility issue with some HDMI devices

#50 mithro opened 8 years ago
0
Allow selection of the voltage level for the TOFE connector

#49 mithro opened 8 years ago
0
FX2 UART lines should have a header on them

#48 mithro opened 8 years ago
0
Pin 2 of PCIe connector should be NC

#47 mithro opened 8 years ago
0
Fix label of PCIe 12V connector

#46 mithro opened 8 years ago
0
Clock loopback output pins not on differential output compatible bank

#45 mithro opened 8 years ago
0
Rename files from HDMI2USB to Opsis

#44 mithro opened 8 years ago
0
Remove unused library "special" from the design

#43 mithro opened 8 years ago
0
Issue with clock labelling

#42 mithro closed 8 years ago
0
Convert schematic and design to KiCad 4.0 format

#41 mithro opened 9 years ago
0
Changes on 2015-11-03 3.50PM

#40 numato-anoopjose closed 9 years ago
0
Changes on 2015-11-02

#39 numato-anoopjose closed 9 years ago
0
Changes on 2015-10-21

#38 numato-anoopjose closed 9 years ago
10
Noise on DisplayPort high speed lines when using the AUX connector

#37 mithro opened 9 years ago
3
Numbering of HDMI ports on silkscreen different from in lm32

#36 sealne closed 9 years ago
1
Add a header to the SD card pins

#35 mithro closed 9 years ago
2
Add a jumper between RESET# pin and the FPGA pin G22

#34 mithro closed 9 years ago
0
Change JEEADDR label to JMAC-ADR

#33 mithro closed 9 years ago
0
Make the EEPROM write protected by default (with a jumper to enable writing)

#32 mithro closed 9 years ago
0
Mini-ITX case alignment issue for I/O shield

#31 mithro closed 9 years ago
7
Create a KiCad template for TOFE expansion boards

#30 mithro closed 9 years ago
2
All EDID/HPD/CEC test points should be grouped together logically

#29 mithro opened 9 years ago
0
TX1's test points are scattered all over the place

#28 mithro closed 9 years ago
1
All test points should be labelled on both sides of the board

#27 mithro closed 9 years ago
0
PCB should have git revision number embedded in it

#26 mithro opened 9 years ago
1
DisplayPort lanes on the sink are incorrect

#25 mithro closed 9 years ago
5
Feature: VGA-in

#24 tillsteinbach closed 9 years ago
7
HDMI signals change names between HDMI sheet and FPGA_Bank_1_2 sheet

#23 mithro closed 9 years ago
0
HDMI low speed signal grouping in "root" sheet is weird

#22 mithro closed 9 years ago
0
Would be nice to "detect supply voltage" on AUX channel of the DisplayPort RX port

#21 mithro opened 9 years ago
0
What is R99 and why is it unpopulated / unknown.

#20 mithro closed 9 years ago
4
Common pin of the 5V power regulators for HDMI output are not connected to ground.

#19 mithro closed 9 years ago
3
Add mounting holes for expansion boards when using a right-angle riser.

#18 mithro closed 9 years ago
5
HPD and CEC lines should have test points

#17 mithro closed 9 years ago
1
Issues with low speed signal lines HDMI signal

#16 mithro closed 9 years ago
6