search

tjhorner / blog-comments

0 stars 0 forks source link

emporia-smart-plugs-tasmota/ #2

Open utterances-bot opened 1 year ago

utterances-bot commented 1 year ago

Unlock the Full Power of Cheap Smart Plugs with Tasmota

Learn how to install open source firmware on a cheap Emporia smart plug in order to unlock its full potential.

https://blog.horner.tj/emporia-smart-plugs-tasmota/

wbarber69 commented 1 year ago

how would one go about installing esphome on these?

wbarber69 commented 1 year ago

also Im using a slightly newer version of the plug, did you ever find out if the rx and tx lines were connected to points on the soldered in board adjacet to those pads

wbarber69 commented 1 year ago

Thanks for nothing

Sent from my iPhone

On Jul 19, 2022, at 9:08 PM, utterances bot @.***> wrote:



Unlock the Full Power of Cheap Smart Plugs with Tasmota

Learn how to install open source firmware on a cheap Emporia smart plug in order to unlock its full potential.

https://blog.horner.tj/emporia-smart-plugs-tasmota/

— Reply to this email directly, view it on GitHubhttps://github.com/tjhorner/blog-comments/issues/2, or unsubscribehttps://github.com/notifications/unsubscribe-auth/AAPMZWRX42RJF5YH2CQXSP3VU5NRPANCNFSM54B5HKUQ. You are receiving this because you commented.Message ID: @.***>

tjhorner commented 1 year ago

You can install ESPHome on these the same way, just use ESPHome firmware instead of Tasmota. There are configs available online for these kinds of plugs. I don't know where the rx and tx lines are on that daughterboard, sorry.

Thanks for nothing

Huh? Was it because I didn't respond immediately? I can't monitor my GitHub notifications 24/7, you know

wbarber69 commented 1 year ago

Because you responded with a link to the same page I contacted you from

Sent from my iPhone

On Jul 20, 2022, at 2:59 PM, TJ Horner @.***> wrote:



You can install ESPHome on these the same way, just use ESPHome firmware instead of Tasmota. There are configs available online for these kinds of plugs. I don't know where the rx and tx lines are on that daughterboard, sorry.

Thanks for nothing

Huh? Was it because I didn't respond immediately?

— Reply to this email directly, view it on GitHubhttps://github.com/tjhorner/blog-comments/issues/2#issuecomment-1190697929, or unsubscribehttps://github.com/notifications/unsubscribe-auth/AAPMZWVQZTVXYPVV22CAYVTVVBLAZANCNFSM54B5HKUQ. You are receiving this because you commented.Message ID: @.***>

tjhorner commented 1 year ago

I didn't do anything like that. It must have been GitHub automatically sending an email to you when the issue was opened

boilermaker-ben commented 6 months ago

Just got another set of four ZooZee SA102 plugs (same internals) and was happy to see you were able to make use of my diagram. Nice write-up!

bobpaul commented 1 month ago

I have a couple of EMS01s. I wasn't sure if the window would line up, so I used a heating pad meant for removing phone screens and heated the long sides, one at a time, then cut into the edge. I'm not sure how much glue there actually is, but there are 4 clips. I managed to avoid mangling things too badly.

Once it was separated into 2 pieces, I cut a deep score to the right of the neutral plug. This allowed folding the plastic up, rather than cutting a window, to get access to the solder points.