HSPA+ its not working

[GoogleCodeExporter]

Please describe the problem in detail. Be sure to include:
HSPA+ its not working

What steps will reproduce the problem?
only works 2G, 3G and 3.5G

What is the expected output? What do you see instead?
supposedly hspa+ was fixed in the last release 

What version of aospX are you using? And when did the issue first start?
Version BR7 , hspa+ never works

Please list the kernel version under Settings->About phone
kernel 2.6.35.14-oaspx-grapefruit

Does the issue happen after a full wipe and without any data restored?
Yes, i does.

Inspire4G or DesireHD? (If Inspire, did you flash Inspiremod?)
Inspire4G , yes inspiremod flashed

Please provide logcat ouput and any additional information below.
(logs required or I will discard the ticket.)

Original issue reported on code.google.com by pablitom...@gmail.com on 20 Sep 2012 at 3:30

[GoogleCodeExporter]

I get the same internet speed with that latest aospx as I did with the 
Inspire's stock Gingerbread.  It is my understanding that HSPS+ is 3.5G, in 
addition the signal indicator changes to "H+" when it gets a 3.5g signal; it 
also goes to "E" for 2g and "3g" for 3g signals. 

Inspire should have never had "4g" in its title. 

Original comment by frmorri...@gmail.com on 24 Sep 2012 at 7:44

[GoogleCodeExporter]

Correct, HSPA+ is pretty much 3.5G, LTE=4G.

frmorrison, does it show the H+ icon with BR7? The only changes made in latest 
release for HSPA+ was just adding H+ icons to SystemUI, it should be showing H+ 
instead of just H when connected to H+ network.. (it doesnt change anything 
connection wise, it should just show the H+ icon now...I dont have H+ support 
in my area to test personally).

Original comment by robbe...@gmail.com on 25 Sep 2012 at 3:28

[GoogleCodeExporter]

I was mistaken earlier, I only see a "H" icon, not a "H+" with BR7; I have 
HSPA+ service in Jacksonville with AT&T.  I just see either E, 3g, or H.  

Original comment by frmorri...@gmail.com on 25 Sep 2012 at 6:43

[GoogleCodeExporter]

Alright, thanks... But yea, as far as connection wise goes H+ should have 
always worked, the code has been there for HSPA+ but it would just show H.. In 
BR7 H+ support was added to SystemUI, but more may be needed for it to show up. 

Original comment by robbe...@gmail.com on 25 Sep 2012 at 10:38

[GoogleCodeExporter]

I can say that I have never seen it show H+ on BR7 either, and I have HSPA+ 
coverage here in Chicago.

Original comment by WindyCit...@gmail.com on 25 Sep 2012 at 11:57

[GoogleCodeExporter]

Ok, so just to confirm.., HSPA+ connection does work but it still just shows H 
instead of H+ in statusbar? So mainly its just a cosmetic issue?

Original comment by robbe...@gmail.com on 26 Sep 2012 at 3:33

[GoogleCodeExporter]

Yeah, I get pretty solid HSPA+ speeds, so it's probably just cosmetic.

Original comment by WindyCit...@gmail.com on 26 Sep 2012 at 10:52

[GoogleCodeExporter]

thank you, i was confused by de H/H+, now i know that hspa+ = 3.5G, this is a 
great rom, good job. 

Original comment by pablitom...@gmail.com on 27 Sep 2012 at 2:49

[GoogleCodeExporter]

Im going to mark this 'Wont Fix' because technically by default ICS only shows 
H/H+ as H in the status bar (There were no H+ icons in stock ICS source, just 
H). Having it show H+ is something cosmetic, as H+ connections work fine. 
Although im marking this 'Wont Fix', this will be addressed later once I figure 
out what all else needs to be done, but technically this is not an issue, just 
normal ICS behavior

Original comment by robbe...@gmail.com on 29 Sep 2012 at 6:01

• Changed state: WontFix