loss sensor doesn't report value

[Red5d]

I've configured my ping sensor like this:

sensor:
  - platform: ping
    ip_address: 8.8.8.8
    num_attempts: 15
    timeout: 60sec
    loss:
      name: Packet Loss
      id: loss
      on_value:
      then:
        - switch.turn_off: relay
        - delay: 15s
        - switch.turn_on: relay

     update_interval: 30s

However, its state only shows up as "NA" in the esphome webui, or "Unknown" in Home Assistant. I've tested with it being able to reach 8.8.8.8 and also having a firewall rule that drops ICMP from its IP address, and the logs reflect that (ping success and failure), but the sensor value doesn't change at all. Am I missing something?

[trombik]

please provide logs.

[Red5d]

The only logs I get from it is this (repeated every minute) when ping is blocked:

19:20:24 | [I] | [ping:040] | no reply from 8.8.8.8

...and this when it's not blocked (every minute):

21:06:24 | [I] | [ping:035] | 64 bytes from 8.8.8.8: icmp_seq=4 ttl=58 time=19 ms

Here's my full esphome config:

esphome:
  name: router-rebooter
  libraries:
    - ESP8266WiFi
    - https://github.com/akaJes/AsyncPing#95ac7e4

esp8266:
  board: esp01_1m

# Enable logging
logger:

# Enable Home Assistant API
api:

web_server:
  local: true

ota:

wifi:
  ssid: !secret wifi_ssid
  password: !secret wifi_password

  # Enable fallback hotspot (captive portal) in case wifi connection fails
  ap:
    ssid: "Router-Rebooter Fallback Hotspot"

captive_portal:

external_components:
  - source:
      type: git
      url: https://github.com/trombik/esphome-component-ping
      ref: main

binary_sensor:
  - platform: gpio
    pin:
      number: GPIO0
      mode:
        input: true
        pullup: true
      inverted: true
    name: "Sonoff Basic Button"
    on_press:
      - switch.toggle: relay

switch:
  - platform: gpio
    name: "Sonoff Basic Relay"
    pin: GPIO12
    id: relay
    restore_mode: ALWAYS_ON

status_led:
  pin:
    number: GPIO13
    inverted: yes

sensor:
  - platform: ping
    ip_address: 8.8.8.8
    num_attempts: 15
    timeout: 60sec
    loss:
      name: Packet Loss
      id: loss
      on_value:
        then:
          - switch.turn_off: relay
          - delay: 15s
          - switch.turn_on: relay

    update_interval: 30s

[trombik]

there should be logs like below:

[I][ping_esp32:089]: 17 packets transmitted, 15 received, 11% packet loss, total time 3028ms avg time 68ms
[D][sensor:117]: 'Packet loss': Sending state 11.00000 % with 0 decimals of accuracy
[D][sensor:117]: 'Latency': Sending state 0.06800 s with 3 decimals of accuracy

please enable debug log, and paste "all" the logs.

[Red5d]

Here are my logs with the "logger: debug" option set in the config:

INFO Reading configuration /config/router-rebooter.yaml... INFO Updating https://github.com/trombik/esphome-component-ping@main INFO Starting log output from router-rebooter.local using esphome API INFO Successfully connected to router-rebooter.local [21:58:27][I][app:102]: ESPHome version 2023.1.0-dev compiled on Jan 21 2023, 19:37:28 [21:58:27][C][status_led:019]: Status LED: [21:58:27][C][status_led:020]: Pin: GPIO13

[21:58:28][C][logger:293]: Logger: [21:58:28][C][logger:294]: Level: DEBUG [21:58:28][C][logger:295]: Log Baud Rate: 115200 [21:58:28][C][logger:296]: Hardware UART: UART0 [21:58:28][C][switch.gpio:076]: GPIO Switch 'Sonoff Basic Relay' [21:58:28][C][switch.gpio:098]: Restore Mode: always ON [21:58:28][C][switch.gpio:031]: Pin: GPIO12 [21:58:28][C][gpio.binary_sensor:015]: GPIO Binary Sensor 'Sonoff Basic Button' [21:58:28][C][gpio.binary_sensor:016]: Pin: GPIO0 [21:58:28][C][captive_portal:088]: Captive Portal: [21:58:28][C][web_server:151]: Web Server: [21:58:28][C][web_server:152]: Address: router-rebooter.local:80 [21:58:28][C][mdns:106]: mDNS: [21:58:28][C][mdns:107]: Hostname: router-rebooter [21:58:28][C][ota:093]: Over-The-Air Updates: [21:58:28][C][ota:094]: Address: router-rebooter.local:8266 [21:58:28][C][api:138]: API Server: [21:58:28][C][api:139]: Address: router-rebooter.local:6053 [21:58:28][C][api:143]: Using noise encryption: NO [21:59:32][I][ping:040]: no reply from 8.8.8.8 [22:00:32][I][ping:040]: no reply from 8.8.8.8 [22:01:32][I][ping:040]: no reply from 8.8.8.8 [22:02:32][I][ping:040]: no reply from 8.8.8.8 [22:03:32][I][ping:040]: no reply from 8.8.8.8 [22:04:32][I][ping:040]: no reply from 8.8.8.8 [22:05:32][I][ping:040]: no reply from 8.8.8.8 [22:05:32][I][ping:035]: 64 bytes from 8.8.8.8: icmp_seq=8 ttl=57 time=19 ms [22:06:32][I][ping:035]: 64 bytes from 8.8.8.8: icmp_seq=9 ttl=57 time=18 ms [22:08:32][I][ping:040]: no reply from 8.8.8.8 [22:09:32][I][ping:040]: no reply from 8.8.8.8 The only debug logs I see are when I turn the relay on/off: 22:10:46 | [D] | [switch:017] | 'Sonoff Basic Relay' Turning OFF. 22:10:46 | [D] | [switch:056] | 'Sonoff Basic Relay': Sending state OFF 22:10:47 | [D] | [switch:013] | 'Sonoff Basic Relay' Turning ON. 22:10:47 | [D] | [switch:056] | 'Sonoff Basic Relay': Sending state ON I've tried on both the "latest" and "dev" esphome versions, but still not seeing debug logs like your example there. Not sure if there's a debug setting I don't know about or an issue with esphome or something.

[trombik]

I can't find any logs fro "sensor" component. Try one of the examples, and make sure that the log includes messages from "sensor" component. After that, modify the config to your needs.