Open DS455 opened 3 months ago
Hi, Is it possible to add this device to a monitoring template?
=== START OF INFORMATION SECTION === Model Family: Innodisk 1IE3/3IE3/3ME3/3IE4/3ME4 SSDs Device Model: CFast 3ME4 Serial Number: LU WWN Device Id: 5 24693e 112009c5e Firmware Version: L20420 User Capacity: 128,035,676,160 bytes [128 GB] Sector Size: 512 bytes logical/physical Rotation Rate: Solid State Device TRIM Command: Available, deterministic, zeroed Device is: In smartctl database 7.3/5528 ATA Version is: ACS-3 T13/2161-D revision 4 SATA Version is: SATA 3.2, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Tue Jun 18 15:31:46 2024 RTZST SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x02) Offline data collection activity was completed without error. Auto Offline Data Collection: Disabled. Total time to complete Offline data collection: ( 32) seconds. Offline data collection capabilities: (0x00) Offline data collection not supported. SMART capabilities: (0x0002) Does not save SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x00) Error logging NOT supported. General Purpose Logging supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x0000 000 000 000 Old_age Offline - 0 2 Throughput_Performance 0x0000 000 000 000 Old_age Offline - 0 5 Later_Bad_Block 0x0012 100 100 001 Old_age Always - 0 7 Seek_Error_Rate 0x0000 000 000 000 Old_age Offline - 0 8 Seek_Time_Performance 0x0000 000 000 000 Old_age Offline - 0 9 Power_On_Hours 0x0012 143 000 000 Old_age Always - 27900 10 Spin_Retry_Count 0x0000 000 000 000 Old_age Offline - 0 12 Power_Cycle_Count 0x0012 035 000 000 Old_age Always - 35 163 Total_Bad_Block_Count 0x0000 000 000 000 Old_age Offline - 8 168 SATA_PHY_Error_Count 0x0000 000 000 000 Old_age Offline - 0 169 Remaining_Lifetime_Perc 0x0000 077 000 000 Old_age Offline - 77 175 Bad_Cluster_Table_Count 0x0000 000 000 000 Old_age Offline - 0 192 Power-Off_Retract_Count 0x0012 000 000 000 Old_age Always - 5 194 Temperature_Celsius 0x0002 050 100 000 Old_age Always - 51 (3 66 0 38 0) 197 Current_Pending_Sector 0x0000 000 000 000 Old_age Offline - 0 225 Data_Log_Write_Count 0x0000 000 000 000 Old_age Offline - 0 240 Write_Head 0x0000 000 000 000 Old_age Offline - 0 165 Max_Erase_Count 0x0012 241 100 000 Old_age Always - 753 167 Average_Erase_Count 0x0012 000 100 000 Old_age Always - 713 170 Spare_Block_Count 0x0013 100 100 010 Pre-fail Always - 144 171 Program_Fail_Count 0x0012 000 100 000 Old_age Always - 0 172 Erase_Fail_Count 0x0012 000 100 000 Old_age Always - 0 176 RANGE_RECORD_Count 0x0000 000 000 000 Old_age Offline - 0 184 End-to-End_Error 0x0012 000 000 000 Old_age Always - 0 187 Reported_Uncorrect 0x0012 000 000 000 Old_age Always - 0 229 Flash_ID 0x0000 100 100 000 Old_age Offline - 0x517693943a98 232 Spares_Remaining_Perc 0x0013 000 000 000 Pre-fail Always - 0 235 Later_Bad_Blk_Inf_R/W/E 0x0002 000 000 000 Old_age Always - 0 0 0 241 Host_Writes_32MiB 0x0002 100 100 000 Old_age Always - 1034520 242 Host_Reads_32MiB 0x0002 100 100 000 Old_age Always - 157519 SMART Error Log not supported SMART Self-test Log not supported Selective Self-tests/Logging not supported
Hi, Is it possible to add this device to a monitoring template?