Closed warpme closed 1 year ago
warpme
commented
1 year ago Hi,
No SDIO in dmesg most probably means no power is enabled for SDIO interface by sdio-pwrseq. Most probably because DT has wrong pin declaration for GPIO pin used to turn-on power on SDIO interface. May you boot android on this box and get GPIO info? Probably below commands in android terminal will be enough:
mount -t debugfs debugfs /sys/kernel/debug
cat /sys/kernel/debug/gpio 
arg7
commented
1 year ago Thanks for your support: cat /sys/kernel/debug/gpio shows:
gpiochip1: GPIOs 0-287, parent: platform/pio, pio:
gpio-207 ( |wlan_hostwake ) in lo
gpio-208 ( |bt_hostwake ) in hi
gpio-209 ( |bt_wake ) out hi
gpio-210 ( |wlan_regon ) out hi
gpio-211 ( |bt_rst ) out lo
gpio-230 ( |? ) out hi
gpio-231 ( |? ) out lo
gpio-232 ( |? ) out hi
gpio-267 ( |fd650_clk ) out hi
gpio-268 ( |fd650_dat ) in hi
gpio-272 ( |cd ) in hi
also i've noticed that lsmod shows:
Module Size Used by
bcmdhd 1323008 0
bcm_btlpm 16384 0
uvcvideo 102400 0
videobuf2_v4l2 28672 1 uvcvideo
videobuf2_vmalloc 16384 1 uvcvideo
videobuf2_memops 16384 1 videobuf2_vmalloc
videobuf2_core 49152 2 uvcvideo,videobuf2_v4l2
mali_kbase 544768 7
and dmesg | grep wlan shows:
[ 33.418772] ======== dhd_wlan_init_plat_data ========
[ 33.428718] dhd_wlan_init_gpio: WL_HOST_WAKE=-1, oob_irq=192, oob_irq_flags=0x4084
[ 33.437789] dhd_wlan_init_gpio: WL_REG_ON=-1
[ 33.788535] sunxi-wlan soc@03000000:wlan: bus_index: 1
[ 34.333760] Register interface [wlan0] MAC: e0:76:d0:4f:0e:e4\x0a
[ 34.535457] init: Created socket '/dev/socket/wpa_wlan0', mode 660, user 1010, group 1010looks like bcmdhd is responsible for wifi, but it is not present in MiniArch.
Best regards, AR
arg7
commented
1 year ago I've made a donation of 200PL to your cause. if you wish, I can ship TX6S to you. It would be nice to use a cheap TX6S as Raspberry Pi 4 replacement, given its shortage on the market.
warpme
commented
1 year ago Sorry for delay. (i was a bit busy with adding usb/pcie/eth for rk3588 soc)
Many thx for donation!
Offer of sending to me box for fixing wifi is very kind - lets park this as plan B :-) My plan A is do my best to get wifi working with minimal effort from your side.
GPIO info you provided me conforms GPIO pin used to power-on wifi module is correct one (android says gpio-210 wich is PG18) DT seems to set it correctly (https://github.com/warpme/minimyth2/blob/4f5f0d2bd8d43b80d655a7d6a2ee151273bd92b2/script/kernel/linux-6.2/files/0633-arm64-dts-allwinner-h616-add-Tanix-TX6s-TVbox.patch#L87)).
I have another box with working ok ap6330. It looks like your's tx6s has dead wifi because no 32kHz clock is supplied to ap6330 module. I'm investigating how to add such 32k clock in h616 platforms.
Stay tuned!
ps: once again: many thx for recognising my work!
warpme
commented
1 year ago I added 32k clock in tx6s dt (5ab0a928).
May you pls try update kernel in miniarch?
(in terminal pls type 'start' and select '4')
This should update kernel to 6.2.2.
Reboot and pls provide me:
-dmesg
-cat /sys/kernel/debug/clk/clk_summary
If there will be still issue with wifi, pls provide me cat /sys/kernel/debug/clk/clk_summary also from android
arg7
commented
1 year ago Hi Piotr, thank you for your effort, I'did upgrade to kernel 6.2.2, but wifi still doen't works, unfortunatelly.
Here is output of dmesg:
[ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd034]
[ 0.000000] Linux version 6.2.2 (piotro@minimyth2-aarch64) (aarch64-minimyth-linux-gnu-gcc (GCC) 12.2.0, GNU ld (GNU Binutils) 2.40) #1 SMP PREEMPT Sun Mar 5 20:35:03 CET 2023
[ 0.000000] Machine model: Tanix TX6s
[ 0.000000] efi: UEFI not found.
[ 0.000000] earlycon: uart0 at MMIO32 0x0000000005000000 (options '115200n8')
[ 0.000000] printk: bootconsole [uart0] enabled
[ 0.000000] Zone ranges:
[ 0.000000] DMA [mem 0x0000000040000000-0x00000000ffffffff]
[ 0.000000] DMA32 empty
[ 0.000000] Normal empty
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000040000000-0x000000004007ffff]
[ 0.000000] node 0: [mem 0x0000000040080000-0x00000000ffffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000040000000-0x00000000ffffffff]
[ 0.000000] cma: Reserved 256 MiB at 0x00000000ec800000
[ 0.000000] psci: probing for conduit method from DT.
[ 0.000000] psci: PSCIv1.1 detected in firmware.
[ 0.000000] psci: Using standard PSCI v0.2 function IDs
[ 0.000000] psci: MIGRATE_INFO_TYPE not supported.
[ 0.000000] psci: SMC Calling Convention v1.2
[ 0.000000] percpu: Embedded 29 pages/cpu s80872 r8192 d29720 u118784
[ 0.000000] pcpu-alloc: s80872 r8192 d29720 u118784 alloc=29*4096
[ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3
[ 0.000000] Detected VIPT I-cache on CPU0
[ 0.000000] alternatives: applying boot alternatives
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 774144
[ 0.000000] Kernel command line: root=PARTUUID=346d1a6a-02 rw rootwait earlycon console=ttyS0,115200n8 logo.nologo vt.cur_default=1 deferred_probe_timeout=0 cma=256M
[ 0.000000] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes, linear)
[ 0.000000] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes, linear)
[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[ 0.000000] Memory: 2781488K/3145728K available (14592K kernel code, 3522K rwdata, 6404K rodata, 6720K init, 576K bss, 102096K reserved, 262144K cma-reserved)
[ 0.000000] SLUB: HWalign=64, Order=0-1, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000] ftrace: allocating 51187 entries in 200 pages
[ 0.000000] ftrace: allocated 200 pages with 3 groups
[ 0.000000] trace event string verifier disabled
[ 0.000000] rcu: Preemptible hierarchical RCU implementation.
[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=4.
[ 0.000000] Trampoline variant of Tasks RCU enabled.
[ 0.000000] Rude variant of Tasks RCU enabled.
[ 0.000000] Tracing variant of Tasks RCU enabled.
[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 30 jiffies.
[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4
[ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
[ 0.000000] Root IRQ handler: gic_handle_irq
[ 0.000000] GIC: Using split EOI/Deactivate mode
[ 0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention.
[ 0.000000] arch_timer: cp15 timer(s) running at 24.00MHz (phys).
[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns
[ 0.000001] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns
[ 0.001331] Console: colour dummy device 80x25
[ 0.001415] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=80000)
[ 0.001444] pid_max: default: 32768 minimum: 301
[ 0.001749] Mount-cache hash table entries: 8192 (order: 4, 65536 bytes, linear)
[ 0.001807] Mountpoint-cache hash table entries: 8192 (order: 4, 65536 bytes, linear)
[ 0.003788] cacheinfo: Unable to detect cache hierarchy for CPU 0
[ 0.005623] cblist_init_generic: Setting adjustable number of callback queues.
[ 0.005654] cblist_init_generic: Setting shift to 2 and lim to 1.
[ 0.005918] cblist_init_generic: Setting shift to 2 and lim to 1.
[ 0.006174] cblist_init_generic: Setting shift to 2 and lim to 1.
[ 0.006798] rcu: Hierarchical SRCU implementation.
[ 0.006813] rcu: Max phase no-delay instances is 1000.
[ 0.012124] EFI services will not be available.
[ 0.013488] smp: Bringing up secondary CPUs ...
[ 0.015117] Detected VIPT I-cache on CPU1
[ 0.015250] cacheinfo: Unable to detect cache hierarchy for CPU 1
[ 0.015326] CPU1: Booted secondary processor 0x0000000001 [0x410fd034]
[ 0.017251] Detected VIPT I-cache on CPU2
[ 0.017386] cacheinfo: Unable to detect cache hierarchy for CPU 2
[ 0.017454] CPU2: Booted secondary processor 0x0000000002 [0x410fd034]
[ 0.019283] Detected VIPT I-cache on CPU3
[ 0.019422] cacheinfo: Unable to detect cache hierarchy for CPU 3
[ 0.019491] CPU3: Booted secondary processor 0x0000000003 [0x410fd034]
[ 0.019754] smp: Brought up 1 node, 4 CPUs
[ 0.019790] SMP: Total of 4 processors activated.
[ 0.019803] CPU features: detected: 32-bit EL0 Support
[ 0.019813] CPU features: detected: 32-bit EL1 Support
[ 0.019827] CPU features: detected: CRC32 instructions
[ 0.019984] CPU: All CPU(s) started at EL2
[ 0.020010] alternatives: applying system-wide alternatives
[ 0.023876] devtmpfs: initialized
[ 0.044848] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6370867519511994 ns
[ 0.044912] futex hash table entries: 1024 (order: 4, 65536 bytes, linear)
[ 0.058161] pinctrl core: initialized pinctrl subsystem
[ 0.059081] regulator-dummy: no parameters, enabled
[ 0.060112] DMI not present or invalid.
[ 0.061323] NET: Registered PF_NETLINK/PF_ROUTE protocol family
[ 0.065443] DMA: preallocated 512 KiB GFP_KERNEL pool for atomic allocations
[ 0.065927] DMA: preallocated 512 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations
[ 0.066667] DMA: preallocated 512 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations
[ 0.066831] audit: initializing netlink subsys (disabled)
[ 0.067397] audit: type=2000 audit(0.063:1): state=initialized audit_enabled=0 res=1
[ 0.069931] thermal_sys: Registered thermal governor 'fair_share'
[ 0.069953] thermal_sys: Registered thermal governor 'bang_bang'
[ 0.069965] thermal_sys: Registered thermal governor 'step_wise'
[ 0.069977] thermal_sys: Registered thermal governor 'user_space'
[ 0.070128] cpuidle: using governor ladder
[ 0.070198] cpuidle: using governor menu
[ 0.070529] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
[ 0.070806] ASID allocator initialised with 65536 entries
[ 0.072061] Serial: AMBA PL011 UART driver
[ 0.109861] platform 6510000.tcon-top: Fixing up cyclic dependency with 6000000.hdmi
[ 0.112675] platform 6515000.lcd-controller: Fixing up cyclic dependency with 6510000.tcon-top
[ 0.118086] platform connector: Fixing up cyclic dependency with 6000000.hdmi
[ 0.125913] cryptd: max_cpu_qlen set to 1000
[ 0.128105] ACPI: Interpreter disabled.
[ 0.128980] vcc-5v: 5000 mV, enabled
[ 0.129417] reg-fixed-voltage vcc5v: vcc-5v supplying 5000000uV
[ 0.129872] usb1-vbus: will resolve supply early: vin
[ 0.129893] reg-fixed-voltage usb1-vbus: Looking up vin-supply from device tree
[ 0.129925] usb1-vbus: supplied by vcc-5v
[ 0.129957] vcc-5v: could not add device link regulator.2: -ENOENT
[ 0.130093] usb1-vbus: 5000 mV, enabled
[ 0.130459] reg-fixed-voltage usb1-vbus: usb1-vbus supplying 5000000uV
[ 0.131196] iommu: Default domain type: Translated
[ 0.131211] iommu: DMA domain TLB invalidation policy: strict mode
[ 0.132893] SCSI subsystem initialized
[ 0.133528] usbcore: registered new interface driver usbfs
[ 0.133630] usbcore: registered new interface driver hub
[ 0.133748] usbcore: registered new device driver usb
[ 0.135206] pps_core: LinuxPPS API ver. 1 registered
[ 0.135223] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 0.135279] PTP clock support registered
[ 0.137206] Advanced Linux Sound Architecture Driver Initialized.
[ 0.139403] vgaarb: loaded
[ 0.140345] clocksource: Switched to clocksource arch_sys_counter
[ 0.141671] pnp: PnP ACPI: disabled
[ 0.165941] NET: Registered PF_INET protocol family
[ 0.166567] IP idents hash table entries: 65536 (order: 7, 524288 bytes, linear)
[ 0.175116] tcp_listen_portaddr_hash hash table entries: 2048 (order: 3, 32768 bytes, linear)
[ 0.175236] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear)
[ 0.175271] TCP established hash table entries: 32768 (order: 6, 262144 bytes, linear)
[ 0.175868] TCP bind hash table entries: 32768 (order: 8, 1048576 bytes, linear)
[ 0.177784] TCP: Hash tables configured (established 32768 bind 32768)
[ 0.178113] UDP hash table entries: 2048 (order: 4, 65536 bytes, linear)
[ 0.178344] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes, linear)
[ 0.178860] NET: Registered PF_UNIX/PF_LOCAL protocol family
[ 0.180135] RPC: Registered named UNIX socket transport module.
[ 0.180163] RPC: Registered udp transport module.
[ 0.180175] RPC: Registered tcp transport module.
[ 0.180186] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.180204] NET: Registered PF_XDP protocol family
[ 0.180236] PCI: CLS 0 bytes, default 64
[ 0.181330] Trying to unpack rootfs image as initramfs...
[ 0.189085] hw perfevents: enabled with armv8_cortex_a53 PMU driver, 7 counters available
[ 0.190508] kvm [1]: IPA Size Limit: 40 bits
[ 0.194664] kvm [1]: vgic interrupt IRQ9
[ 0.194980] kvm [1]: Hyp mode initialized successfully
[ 1.020023] Freeing initrd memory: 7448K
[ 2.782632] Initialise system trusted keyrings
[ 2.783243] workingset: timestamp_bits=46 max_order=20 bucket_order=0
[ 2.783513] zbud: loaded
[ 2.784963] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 2.786026] NFS: Registering the id_resolver key type
[ 2.786103] Key type id_resolver registered
[ 2.786116] Key type id_legacy registered
[ 2.786183] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[ 2.786201] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering...
[ 2.888874] NET: Registered PF_ALG protocol family
[ 2.888925] Key type asymmetric registered
[ 2.888940] Asymmetric key parser 'x509' registered
[ 2.888954] Asymmetric key parser 'pkcs8' registered
[ 2.888967] Key type pkcs7_test registered
[ 2.889134] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247)
[ 2.889586] io scheduler mq-deadline registered
[ 2.889606] io scheduler kyber registered
[ 2.889677] io scheduler bfq registered
[ 2.914177] EINJ: ACPI disabled.
[ 2.961879] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[ 2.968583] Serial: AMBA driver
[ 2.989625] cacheinfo: Unable to detect cache hierarchy for CPU 0
[ 3.006596] usbcore: registered new interface driver usb-storage
[ 3.006685] usbcore: registered new interface driver ums-realtek
[ 3.006907] usbcore: registered new interface driver usbserial_generic
[ 3.006978] usbserial: USB Serial support registered for generic
[ 3.011864] mousedev: PS/2 mouse device common for all mice
[ 3.015212] sun6i-rtc 7000000.rtc: registered as rtc0
[ 3.015290] sun6i-rtc 7000000.rtc: setting system clock to 1970-01-02T00:38:50 UTC (88730)
[ 3.015602] sun6i-rtc 7000000.rtc: RTC enabled
[ 3.017476] mv64xxx_i2c 5002c00.i2c: can't get pinctrl, bus recovery not supported
[ 3.023481] cpu cpu0: Looking up cpu-supply from device tree
[ 3.026901] sdhci: Secure Digital Host Controller Interface driver
[ 3.026927] sdhci: Copyright(c) Pierre Ossman
[ 3.027718] Synopsys Designware Multimedia Card Interface Driver
[ 3.031984] sdhci-pltfm: SDHCI platform and OF driver helper
[ 3.035554] ledtrig-cpu: registered to indicate activity on CPUs
[ 3.037909] SMCCC: SOC_ID: ID = jep106:091e:1823 Revision = 0x00000000
[ 3.038068] hid: raw HID events driver (C) Jiri Kosina
[ 3.038281] usbcore: registered new interface driver usbhid
[ 3.038294] usbhid: USB HID core driver
[ 3.081141] sunxi-hdmi soc:hdmi-audio@1: snd_soc_register_card failed
[ 3.081806] NET: Registered PF_PACKET protocol family
[ 3.082514] Key type dns_resolver registered
[ 3.110913] registered taskstats version 1
[ 3.111351] Loading compiled-in X.509 certificates
[ 3.112113] zswap: loaded using pool lzo/zbud
[ 3.154704] platform 1100000.mixer: Fixing up cyclic dependency with 6510000.tcon-top
[ 3.158664] sun4i-usb-phy 5100400.phy: Looking up usb0_vbus-supply from device tree
[ 3.158710] sun4i-usb-phy 5100400.phy: Looking up usb0_vbus-supply property in node /soc/phy@5100400 failed
[ 3.158919] phy phy-5100400.phy.0: Looking up phy-supply from device tree
[ 3.158945] phy phy-5100400.phy.0: Looking up phy-supply property in node /soc/phy@5100400 failed
[ 3.159178] sun4i-usb-phy 5100400.phy: Looking up usb1_vbus-supply from device tree
[ 3.159764] phy phy-5100400.phy.1: Looking up phy-supply from device tree
[ 3.159791] phy phy-5100400.phy.1: Looking up phy-supply property in node /soc/phy@5100400 failed
[ 3.160004] sun4i-usb-phy 5100400.phy: Looking up usb2_vbus-supply from device tree
[ 3.160030] sun4i-usb-phy 5100400.phy: Looking up usb2_vbus-supply property in node /soc/phy@5100400 failed
[ 3.160223] phy phy-5100400.phy.2: Looking up phy-supply from device tree
[ 3.160248] phy phy-5100400.phy.2: Looking up phy-supply property in node /soc/phy@5100400 failed
[ 3.160550] sun4i-usb-phy 5100400.phy: Looking up usb3_vbus-supply from device tree
[ 3.160576] sun4i-usb-phy 5100400.phy: Looking up usb3_vbus-supply property in node /soc/phy@5100400 failed
[ 3.160767] phy phy-5100400.phy.3: Looking up phy-supply from device tree
[ 3.160792] phy phy-5100400.phy.3: Looking up phy-supply property in node /soc/phy@5100400 failed
[ 3.163231] gpio gpiochip0: Static allocation of GPIO base is deprecated, use dynamic allocation.
[ 3.186353] sun50i-h616-pinctrl 300b000.pinctrl: initialized sunXi PIO driver
[ 3.192022] sun50i-h616-pinctrl 300b000.pinctrl: Looking up vcc-ph-supply from device tree
[ 3.192139] sun50i-h616-pinctrl 300b000.pinctrl: Looking up vcc-ph-supply property in node /soc/pinctrl@300b000 failed
[ 3.192205] sun50i-h616-pinctrl 300b000.pinctrl: supply vcc-ph not found, using dummy regulator
[ 3.193918] printk: console [ttyS0] disabled
[ 3.194124] 5000000.serial: ttyS0 at MMIO 0x5000000 (irq = 285, base_baud = 1500000) is a 16550A
[ 3.194274] printk: console [ttyS0] enabled
[ 3.194292] printk: bootconsole [uart0] disabled
[ 3.199472] sun50i-h616-pinctrl 300b000.pinctrl: Looking up vcc-pg-supply from device tree
[ 3.199589] sun50i-h616-pinctrl 300b000.pinctrl: Looking up vcc-pg-supply property in node /soc/pinctrl@300b000 failed
[ 3.199654] sun50i-h616-pinctrl 300b000.pinctrl: supply vcc-pg not found, using dummy regulator
[ 3.201258] 5000400.serial: ttyS1 at MMIO 0x5000400 (irq = 286, base_baud = 1500000) is a 16550A
[ 3.201699] serial serial0: tty port ttyS1 registered
[ 3.210814] phy phy-5100400.phy.0: Changing dr_mode to 1
[ 3.210856] ehci-platform 5101000.usb: EHCI Host Controller
[ 3.210912] ehci-platform 5101000.usb: new USB bus registered, assigned bus number 1
[ 3.211245] ehci-platform 5101000.usb: irq 287, io mem 0x05101000
[ 3.213104] ehci-platform 5200000.usb: EHCI Host Controller
[ 3.213174] ehci-platform 5200000.usb: new USB bus registered, assigned bus number 2
[ 3.213501] ehci-platform 5200000.usb: irq 288, io mem 0x05200000
[ 3.215923] ehci-platform 5310000.usb: EHCI Host Controller
[ 3.215990] ehci-platform 5310000.usb: new USB bus registered, assigned bus number 3
[ 3.216305] ehci-platform 5310000.usb: irq 289, io mem 0x05310000
[ 3.218334] ehci-platform 5311000.usb: EHCI Host Controller
[ 3.218404] ehci-platform 5311000.usb: new USB bus registered, assigned bus number 4
[ 3.218728] ehci-platform 5311000.usb: irq 290, io mem 0x05311000
[ 3.222827] ohci-platform 5200400.usb: Generic Platform OHCI controller
[ 3.222897] ohci-platform 5200400.usb: new USB bus registered, assigned bus number 5
[ 3.223251] ohci-platform 5200400.usb: irq 292, io mem 0x05200400
[ 3.223778] ehci-platform 5101000.usb: USB 2.0 started, EHCI 1.00
[ 3.224691] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.02
[ 3.224732] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 3.224753] usb usb1: Product: EHCI Host Controller
[ 3.224769] usb usb1: Manufacturer: Linux 6.2.2 ehci_hcd
[ 3.224786] usb usb1: SerialNumber: 5101000.usb
[ 3.225596] ohci-platform 5310400.usb: Generic Platform OHCI controller
[ 3.226513] hub 1-0:1.0: USB hub found
[ 3.226659] hub 1-0:1.0: 1 port detected
[ 3.227100] usb_phy_generic usb_phy_generic.1.auto: dummy supplies not allowed for exclusive requests
[ 3.227557] ohci-platform 5311400.usb: Generic Platform OHCI controller
[ 3.227824] ohci-platform 5311400.usb: new USB bus registered, assigned bus number 6
[ 3.227883] ohci-platform 5310400.usb: new USB bus registered, assigned bus number 7
[ 3.228164] ohci-platform 5311400.usb: irq 294, io mem 0x05311400
[ 3.228238] ohci-platform 5310400.usb: irq 293, io mem 0x05310400
[ 3.237058] ehci-platform 5200000.usb: USB 2.0 started, EHCI 1.00
[ 3.237989] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.02
[ 3.238022] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 3.238043] usb usb2: Product: EHCI Host Controller
[ 3.238059] usb usb2: Manufacturer: Linux 6.2.2 ehci_hcd
[ 3.238076] usb usb2: SerialNumber: 5200000.usb
[ 3.239530] hub 2-0:1.0: USB hub found
[ 3.239679] hub 2-0:1.0: 1 port detected
[ 3.250399] ehci-platform 5310000.usb: USB 2.0 started, EHCI 1.00
[ 3.251289] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.02
[ 3.251322] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 3.251343] usb usb3: Product: EHCI Host Controller
[ 3.251359] usb usb3: Manufacturer: Linux 6.2.2 ehci_hcd
[ 3.251376] usb usb3: SerialNumber: 5310000.usb
[ 3.252839] hub 3-0:1.0: USB hub found
[ 3.252976] hub 3-0:1.0: 1 port detected
[ 3.263732] ehci-platform 5311000.usb: USB 2.0 started, EHCI 1.00
[ 3.264597] usb usb4: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.02
[ 3.264628] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 3.264649] usb usb4: Product: EHCI Host Controller
[ 3.264665] usb usb4: Manufacturer: Linux 6.2.2 ehci_hcd
[ 3.264682] usb usb4: SerialNumber: 5311000.usb
[ 3.266122] hub 4-0:1.0: USB hub found
[ 3.266260] hub 4-0:1.0: 1 port detected
[ 3.281526] usb usb5: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 6.02
[ 3.281566] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 3.281586] usb usb5: Product: Generic Platform OHCI controller
[ 3.281603] usb usb5: Manufacturer: Linux 6.2.2 ohci_hcd
[ 3.281619] usb usb5: SerialNumber: 5200400.usb
[ 3.283042] hub 5-0:1.0: USB hub found
[ 3.283145] hub 5-0:1.0: 1 port detected
[ 3.288178] usb usb7: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 6.02
[ 3.288217] usb usb7: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 3.288239] usb usb7: Product: Generic Platform OHCI controller
[ 3.288256] usb usb7: Manufacturer: Linux 6.2.2 ohci_hcd
[ 3.288272] usb usb7: SerialNumber: 5310400.usb
[ 3.289700] hub 7-0:1.0: USB hub found
[ 3.289799] hub 7-0:1.0: 1 port detected
[ 3.291251] usb usb6: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 6.02
[ 3.291289] usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 3.291310] usb usb6: Product: Generic Platform OHCI controller
[ 3.291327] usb usb6: Manufacturer: Linux 6.2.2 ohci_hcd
[ 3.291344] usb usb6: SerialNumber: 5311400.usb
[ 3.292769] hub 6-0:1.0: USB hub found
[ 3.292875] hub 6-0:1.0: 1 port detected
[ 3.417146] ohci-platform 5101400.usb: Generic Platform OHCI controller
[ 3.417228] ohci-platform 5101400.usb: new USB bus registered, assigned bus number 8
[ 3.417551] ohci-platform 5101400.usb: irq 291, io mem 0x05101400
[ 3.419288] cpu cpu0: Looking up cpu-supply from device tree
[ 3.428870] sun50i-h616-pinctrl 300b000.pinctrl: Looking up vcc-pc-supply from device tree
[ 3.428982] sun50i-h616-pinctrl 300b000.pinctrl: Looking up vcc-pc-supply property in node /soc/pinctrl@300b000 failed
[ 3.429051] sun50i-h616-pinctrl 300b000.pinctrl: supply vcc-pc not found, using dummy regulator
[ 3.432230] sunxi-hdmi soc:hdmi-audio@1: snd_soc_register_card failed
[ 3.432853] vcc-wifi: 3300 mV, enabled
[ 3.433290] reg-fixed-voltage reg_vcc_wifi: vcc-wifi supplying 3300000uV
[ 3.434627] gpio gpiochip1: Static allocation of GPIO base is deprecated, use dynamic allocation.
[ 3.435495] sun50i-h616-r-pinctrl 7022000.pinctrl: initialized sunXi PIO driver
[ 3.437766] cpu cpu0: Looking up cpu-supply from device tree
[ 3.447353] sunxi-hdmi soc:hdmi-audio@1: snd_soc_register_card failed
[ 3.447745] sun50i-h616-r-pinctrl 7022000.pinctrl: Looking up vcc-pl-supply from device tree
[ 3.447787] sun50i-h616-r-pinctrl 7022000.pinctrl: Looking up vcc-pl-supply property in node /soc/pinctrl@7022000 failed
[ 3.447857] sun50i-h616-r-pinctrl 7022000.pinctrl: supply vcc-pl not found, using dummy regulator
[ 3.448818] sunxi-rsb 7083000.rsb: RSB running at 3000000 Hz
[ 3.449455] axp20x-rsb sunxi-rsb-745: AXP20x variant AXP806 found
[ 3.450781] axp20x-rsb sunxi-rsb-745: Looking up vina-supply from device tree
[ 3.450832] vdd-cpu: supplied by vcc-5v
[ 3.450859] vcc-5v: could not add device link regulator.4: -ENOENT
[ 3.451149] vdd-cpu: 810 <--> 1160 mV at 1120 mV, enabled
[ 3.451754] dcdcb: at 1350 mV, enabled
[ 3.452102] axp20x-rsb sunxi-rsb-745: Looking up vinb-supply from device tree
[ 3.452137] dcdcb: supplied by vcc-5v
[ 3.452459] axp20x-rsb sunxi-rsb-745: Looking up vinc-supply from device tree
[ 3.452490] vdd-gpu-sys: supplied by vcc-5v
[ 3.452514] vcc-5v: could not add device link regulator.6: -ENOENT
[ 3.452735] vdd-gpu-sys: 810 <--> 1160 mV at 1080 mV, enabled
[ 3.453304] axp20x-rsb sunxi-rsb-745: Looking up vind-supply from device tree
[ 3.453337] vdd-dram: supplied by vcc-5v
[ 3.453361] vcc-5v: could not add device link regulator.7: -ENOENT
[ 3.453557] vdd-dram: 1500 mV, enabled
[ 3.454214] axp20x-rsb sunxi-rsb-745: Looking up vine-supply from device tree
[ 3.454249] vcc-eth-mmc: supplied by vcc-5v
[ 3.454274] vcc-5v: could not add device link regulator.8: -ENOENT
[ 3.454524] vcc-eth-mmc: 3300 mV, enabled
[ 3.455061] axp20x-rsb sunxi-rsb-745: Looking up aldoin-supply from device tree
[ 3.455094] vcc-sys: supplied by vcc-5v
[ 3.455118] vcc-5v: could not add device link regulator.9: -ENOENT
[ 3.455345] vcc-sys: 3300 mV, enabled
[ 3.455879] axp20x-rsb sunxi-rsb-745: Looking up aldoin-supply from device tree
[ 3.455912] vcc3v3-ext: supplied by vcc-5v
[ 3.455936] vcc-5v: could not add device link regulator.10: -ENOENT
[ 3.456177] vcc3v3-ext: 3300 mV, enabled
[ 3.456727] axp20x-rsb sunxi-rsb-745: Looking up aldoin-supply from device tree
[ 3.456760] vcc3v3-ext2: supplied by vcc-5v
[ 3.456785] vcc-5v: could not add device link regulator.11: -ENOENT
[ 3.457063] vcc3v3-ext2: 3300 mV, enabled
[ 3.457616] axp20x-rsb sunxi-rsb-745: Looking up bldoin-supply from device tree
[ 3.457649] vcc1v8: supplied by vcc-5v
[ 3.457674] vcc-5v: could not add device link regulator.12: -ENOENT
[ 3.457955] vcc1v8: 1800 mV, enabled
[ 3.458578] bldo2: at 1800 mV, disabled
[ 3.458990] axp20x-rsb sunxi-rsb-745: Looking up bldoin-supply from device tree
[ 3.459024] bldo2: supplied by vcc-5v
[ 3.459389] bldo3: at 700 mV, disabled
[ 3.459780] axp20x-rsb sunxi-rsb-745: Looking up bldoin-supply from device tree
[ 3.459813] bldo3: supplied by vcc-5v
[ 3.460176] bldo4: at 700 mV, disabled
[ 3.460678] axp20x-rsb sunxi-rsb-745: Looking up bldoin-supply from device tree
[ 3.460713] bldo4: supplied by vcc-5v
[ 3.461058] cldo1: at 2500 mV, disabled
[ 3.461464] axp20x-rsb sunxi-rsb-745: Looking up cldoin-supply from device tree
[ 3.461496] cldo1: supplied by vcc-5v
[ 3.461906] cldo2: at 700 mV, disabled
[ 3.462323] axp20x-rsb sunxi-rsb-745: Looking up cldoin-supply from device tree
[ 3.462356] cldo2: supplied by vcc-5v
[ 3.462728] cldo3: at 700 mV, disabled
[ 3.463150] axp20x-rsb sunxi-rsb-745: Looking up cldoin-supply from device tree
[ 3.463183] cldo3: supplied by vcc-5v
[ 3.463501] sw: no parameters, disabled
[ 3.463965] axp20x-rsb sunxi-rsb-745: Looking up swin-supply from device tree
[ 3.464072] axp20x-rsb sunxi-rsb-745: Looking up swin-supply property in node /soc/rsb@7083000/pmic@745 failed
[ 3.464176] sw: supplied by regulator-dummy
[ 3.464427] axp20x-rsb sunxi-rsb-745: AXP20X driver loaded
[ 3.468082] debugfs: Directory '1100000.mixer' with parent 'regmap' already present!
[ 3.468187] debugfs: Directory '1100000.mixer' with parent 'regmap' already present!
[ 3.478270] usb usb8: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 6.02
[ 3.478303] usb usb8: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 3.478324] usb usb8: Product: Generic Platform OHCI controller
[ 3.478340] usb usb8: Manufacturer: Linux 6.2.2 ohci_hcd
[ 3.478356] usb usb8: SerialNumber: 5101400.usb
[ 3.479812] hub 8-0:1.0: USB hub found
[ 3.479910] hub 8-0:1.0: 1 port detected
[ 3.505083] sun4i-drm display-engine: bound 1100000.mixer (ops sun8i_mixer_ops)
[ 3.505750] sun4i-drm display-engine: bound 6510000.tcon-top (ops sun8i_tcon_top_ops)
[ 3.506757] sun4i-drm display-engine: bound 6515000.lcd-controller (ops sun4i_tcon_ops)
[ 3.506933] sun8i-dw-hdmi 6000000.hdmi: Looking up hvcc-supply from device tree
[ 3.508078] sun8i-dw-hdmi 6000000.hdmi: Detected HDMI TX controller v2.12a with HDCP (DWC HDMI 2.0 TX PHY)
[ 3.509451] sun8i-dw-hdmi 6000000.hdmi: registered DesignWare HDMI I2C bus driver
[ 3.511316] hdmi_codec_probe: using aw-hdmi-codec-quirk for H616
[ 3.513543] sun4i-drm display-engine: bound 6000000.hdmi (ops sun8i_dw_hdmi_ops)
[ 3.515146] [drm] Initialized sun4i-drm 1.0.0 20150629 for display-engine on minor 0
[ 3.515395] sun4i-drm display-engine: [drm] Cannot find any crtc or sizes
[ 3.517252] cpu cpu0: Looking up cpu-supply from device tree
[ 3.522084] cpufreq: cpufreq_online: CPU0: Running at unlisted initial frequency: 432000 KHz, changing to: 480000 KHz
[ 3.524618] sun50i-h616-pinctrl 300b000.pinctrl: Looking up vcc-pf-supply from device tree
[ 3.524705] sun50i-h616-pinctrl 300b000.pinctrl: Looking up vcc-pf-supply property in node /soc/pinctrl@300b000 failed
[ 3.524778] sun50i-h616-pinctrl 300b000.pinctrl: supply vcc-pf not found, using dummy regulator
[ 3.525136] sunxi-mmc 4020000.mmc: Looking up vmmc-supply from device tree
[ 3.525301] sunxi-mmc 4020000.mmc: Looking up vqmmc-supply from device tree
[ 3.525313] sunxi-mmc 4020000.mmc: Looking up vqmmc-supply property in node /soc/mmc@4020000 failed
[ 3.525770] sunxi-mmc 4021000.mmc: Looking up vmmc-supply from device tree
[ 3.525989] sunxi-mmc 4021000.mmc: Looking up vqmmc-supply from device tree
[ 3.526793] sunxi-mmc 4022000.mmc: Looking up vmmc-supply from device tree
[ 3.526960] sunxi-mmc 4022000.mmc: Looking up vqmmc-supply from device tree
[ 3.526969] sunxi-mmc 4021000.mmc: allocated mmc-pwrseq
[ 3.526974] sunxi-mmc 4022000.mmc: Looking up vqmmc-supply property in node /soc/mmc@4022000 failed
[ 3.528385] ALSA device list:
[ 3.528402] #0: sndahub
[ 3.528407] #1: allwinner-hdmi
[ 3.552308] sunxi-mmc 4021000.mmc: initialized, max. request size: 16384 KB, uses new timings mode
[ 3.552671] sunxi-mmc 4020000.mmc: initialized, max. request size: 16384 KB, uses new timings mode
[ 3.552827] sunxi-mmc 4022000.mmc: initialized, max. request size: 2048 KB, uses new timings mode
[ 3.560041] Freeing unused kernel memory: 6720K
[ 3.560158] Run /init as init process
[ 3.560162] with arguments:
[ 3.560167] /init
[ 3.560171] with environment:
[ 3.560174] HOME=/
[ 3.560177] TERM=linux
[ 3.587541] mmc0: host does not support reading read-only switch, assuming write-enable
[ 3.589487] mmc0: new high speed SDHC card at address 0001
[ 3.590504] mmcblk0: mmc0:0001 00000 14.9 GiB
[ 3.593566] mmcblk0: p1 p2
[ 3.688674] mmc2: new DDR MMC card at address 0001
[ 3.689705] mmcblk2: mmc2:0001 SCA32G 29.1 GiB
[ 3.694236] mmcblk2: p1 p2 p3 p4 p5 p6 p7 p8 p9 p10 p11 p12 p13 p14 p15 p16 p17
[ 3.698376] mmcblk2boot0: mmc2:0001 SCA32G 4.00 MiB
[ 3.701356] mmcblk2boot1: mmc2:0001 SCA32G 4.00 MiB
[ 3.753816] usb 2-1: new high-speed USB device number 2 using ehci-platform
[ 3.902723] usb 2-1: New USB device found, idVendor=04e8, idProduct=6864, bcdDevice= c.00
[ 3.902748] usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 3.902754] usb 2-1: Product: SAMSUNG_Android
[ 3.902759] usb 2-1: Manufacturer: SAMSUNG
[ 3.902763] usb 2-1: SerialNumber: 2329051c8a0c7ece
[ 4.308497] panfrost 1800000.gpu: clock rate = 432000000
[ 4.308541] panfrost 1800000.gpu: bus_clock rate = 200000000
[ 4.308610] panfrost 1800000.gpu: Looking up mali-supply from device tree
[ 4.329711] panfrost 1800000.gpu: mali-g31 id 0x7093 major 0x0 minor 0x0 status 0x0
[ 4.329737] panfrost 1800000.gpu: features: 00000000,000027f7, issues: 00000000,00000400
[ 4.329744] panfrost 1800000.gpu: Features: L2:0x07100206 Shader:0x00000000 Tiler:0x00000209 Mem:0x1 MMU:0x00002821 AS:0xff JS:0x7
[ 4.329752] panfrost 1800000.gpu: shader_present=0x1 l2_present=0x1
[ 4.333308] [drm] Initialized panfrost 1.2.0 20180908 for 1800000.gpu on minor 1
[ 5.188581] EXT4-fs (mmcblk0p2): mounted filesystem 69379c76-4f98-4190-983b-0c4a6031b34c with ordered data mode. Quota mode: disabled.
[ 5.985822] systemd[1]: System time before build time, advancing clock.
[ 6.040959] systemd[1]: Failed to find module 'autofs4'
[ 6.089727] NET: Registered PF_INET6 protocol family
[ 6.090832] Segment Routing with IPv6
[ 6.090874] In-situ OAM (IOAM) with IPv6
[ 6.179376] systemd[1]: systemd 253-1-arch running in system mode (+PAM +AUDIT -SELINUX -APPARMOR -IMA +SMACK +SECCOMP +GCRYPT +GNUTLS +OPENSSL +ACL +BLKID +CURL +ELFUTILS +FIDO2 +IDN2 -IDN +IPTC +KMOD +LIBCRYPTSETUP +LIBFDISK +PCRE2 -PWQUALITY +P11KIT -QRENCODE +TPM2 +BZIP2 +LZ4 +XZ +ZLIB +ZSTD +BPF_FRAMEWORK +XKBCOMMON +UTMP -SYSVINIT default-hierarchy=unified)
[ 6.179409] systemd[1]: Detected architecture arm64.
[ 6.212363] systemd[1]: Hostname set to <alarm>.
[ 6.521390] systemd[1]: bpf-lsm: BPF LSM hook not enabled in the kernel, BPF LSM not supported
[ 7.228023] systemd[1]: Queued start job for default target Graphical Interface.
[ 7.265277] systemd[1]: Created slice Slice /system/getty.
[ 7.285650] systemd[1]: Created slice Slice /system/modprobe.
[ 7.305624] systemd[1]: Created slice Slice /system/serial-getty.
[ 7.325256] systemd[1]: Created slice User and Session Slice.
[ 7.344272] systemd[1]: Started Dispatch Password Requests to Console Directory Watch.
[ 7.364234] systemd[1]: Started Forward Password Requests to Wall Directory Watch.
[ 7.384055] systemd[1]: Starting of Arbitrary Executable File Formats File System Automount Point unsupported.
[ 7.403994] systemd[1]: Reached target Local Encrypted Volumes.
[ 7.420611] systemd[1]: Reached target Local Integrity Protected Volumes.
[ 7.440597] systemd[1]: Reached target Path Units.
[ 7.457232] systemd[1]: Reached target Remote File Systems.
[ 7.473864] systemd[1]: Reached target Slice Units.
[ 7.490606] systemd[1]: Reached target Swaps.
[ 7.507248] systemd[1]: Reached target Local Verity Protected Volumes.
[ 7.527671] systemd[1]: Listening on Device-mapper event daemon FIFOs.
[ 7.552755] systemd[1]: Listening on Process Core Dump Socket.
[ 7.571327] systemd[1]: Listening on Journal Socket (/dev/log).
[ 7.591311] systemd[1]: Listening on Journal Socket.
[ 7.608083] systemd[1]: Listening on Network Service Netlink Socket.
[ 7.628147] systemd[1]: Listening on udev Control Socket.
[ 7.647831] systemd[1]: Listening on udev Kernel Socket.
[ 7.664553] systemd[1]: Huge Pages File System was skipped because of an unmet condition check (ConditionPathExists=/sys/kernel/mm/hugepages).
[ 7.690725] systemd[1]: Mounting POSIX Message Queue File System...
[ 7.711650] systemd[1]: Mounting Kernel Debug File System...
[ 7.731659] systemd[1]: Mounting Kernel Trace File System...
[ 7.753097] systemd[1]: Mounting Temporary Directory /tmp...
[ 7.775715] systemd[1]: Starting Create List of Static Device Nodes...
[ 7.798943] systemd[1]: Starting Load Kernel Module configfs...
[ 7.818986] systemd[1]: Starting Load Kernel Module dm_mod...
[ 7.838848] systemd[1]: Starting Load Kernel Module drm...
[ 7.858875] systemd[1]: Starting Load Kernel Module fuse...
[ 7.878967] systemd[1]: Starting Load Kernel Module loop...
[ 7.895321] loop: module loaded
[ 7.902185] systemd[1]: Starting Journal Service...
[ 7.920943] systemd[1]: Load Kernel Modules was skipped because no trigger condition checks were met.
[ 7.926769] systemd[1]: Starting Generate network units from Kernel command line...
[ 7.944128] systemd[1]: TPM2 PCR Machine ID Measurement was skipped because of an unmet condition check (ConditionPathExists=/sys/firmware/efi/efivars/StubPcrKernelImage-4a67b082-0a4c-41cf-b6c7-440b29bb8c4f).
[ 7.950156] systemd[1]: Starting Remount Root and Kernel File Systems...
[ 7.982222] systemd-journald[176]: Collecting audit messages is disabled.
[ 8.001090] systemd[1]: Starting Apply Kernel Variables...
[ 8.026174] systemd[1]: Starting Coldplug All udev Devices...
[ 8.056728] systemd[1]: Mounted POSIX Message Queue File System.
[ 8.077896] systemd[1]: Mounted Kernel Debug File System.
[ 8.097936] systemd[1]: Mounted Kernel Trace File System.
[ 8.121326] systemd[1]: Mounted Temporary Directory /tmp.
[ 8.141971] systemd[1]: Finished Create List of Static Device Nodes.
[ 8.162387] systemd[1]: modprobe@configfs.service: Deactivated successfully.
[ 8.163263] systemd[1]: Finished Load Kernel Module configfs.
[ 8.182168] systemd[1]: modprobe@dm_mod.service: Deactivated successfully.
[ 8.183047] systemd[1]: Finished Load Kernel Module dm_mod.
[ 8.202233] systemd[1]: modprobe@drm.service: Deactivated successfully.
[ 8.203091] systemd[1]: Finished Load Kernel Module drm.
[ 8.224660] systemd[1]: Started Journal Service.
[ 8.462594] systemd-journald[176]: Received client request to flush runtime journal.
[ 8.475212] systemd-journald[176]: File /var/log/journal/07f2a7232a544115832ab8e20cc7e24c/system.journal corrupted or uncleanly shut down, renaming and replacing.
[ 9.752500] cfg80211: Loading compiled-in X.509 certificates for regulatory database
[ 9.826573] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7'
[ 10.217727] mc: Linux media interface: v0.10
[ 10.226628] sunxi-wdt 30090a0.watchdog: Watchdog enabled (timeout=16 sec, nowayout=0)
[ 10.257265] videodev: Linux video capture interface: v2.00
[ 10.294740] sun50i-di 1420000.deinterlace: Device registered as /dev/video0
[ 10.391367] sunxi_cedrus: module is from the staging directory, the quality is unknown, you have been warned.
[ 10.395137] cedrus 1c0e000.video-codec: Device registered as /dev/video1
[ 10.405029] FAT-fs (mmcblk0p1): Volume was not properly unmounted. Some data may be corrupt. Please run fsck.
[ 10.440673] debugfs: Directory '5096000.codec' with parent 'H616 Audio Codec' already present!
[ 10.441896] sun50i-h616-codec 5096000.codec: ASoC: driver name too long 'H616 Audio Codec' -> 'H616_Audio_Code'
[ 10.468838] sun50i-h616-pinctrl 300b000.pinctrl: Looking up vcc-pa-supply from device tree
[ 10.468887] sun50i-h616-pinctrl 300b000.pinctrl: Looking up vcc-pa-supply property in node /soc/pinctrl@300b000 failed
[ 10.468941] sun50i-h616-pinctrl 300b000.pinctrl: supply vcc-pa not found, using dummy regulator
[ 10.476021] dwmac-sun8i 5030000.ethernet: IRQ eth_wake_irq not found
[ 10.476048] dwmac-sun8i 5030000.ethernet: IRQ eth_lpi not found
[ 10.476111] dwmac-sun8i 5030000.ethernet: Looking up phy-supply from device tree
[ 10.476460] dwmac-sun8i 5030000.ethernet: Looking up phy-io-supply from device tree
[ 10.476492] dwmac-sun8i 5030000.ethernet: Looking up phy-io-supply property in node /soc/ethernet@5030000 failed
[ 10.476546] dwmac-sun8i 5030000.ethernet: supply phy-io not found, using dummy regulator
[ 10.476932] dwmac-sun8i 5030000.ethernet: PTP uses main clock
[ 10.479256] dwmac-sun8i 5030000.ethernet: Current syscon value is not the default 58000 (expect 50000)
[ 10.480546] dwmac-sun8i 5030000.ethernet: No HW DMA feature register supported
[ 10.480572] dwmac-sun8i 5030000.ethernet: RX Checksum Offload Engine supported
[ 10.480577] dwmac-sun8i 5030000.ethernet: COE Type 2
[ 10.480583] dwmac-sun8i 5030000.ethernet: TX Checksum insertion supported
[ 10.480589] dwmac-sun8i 5030000.ethernet: Normal descriptors
[ 10.480593] dwmac-sun8i 5030000.ethernet: Chain mode enabled
[ 10.534268] Bluetooth: Core ver 2.22
[ 10.534417] NET: Registered PF_BLUETOOTH protocol family
[ 10.534422] Bluetooth: HCI device and connection manager initialized
[ 10.534444] Bluetooth: HCI socket layer initialized
[ 10.534453] Bluetooth: L2CAP socket layer initialized
[ 10.534479] Bluetooth: SCO socket layer initialized
[ 10.560503] Registered IR keymap rc-beelink-gs1
[ 10.606339] IR NEC protocol handler initialized
[ 10.623719] random: crng init done
[ 10.633974] rc rc0: sunxi-ir as /devices/platform/soc/7040000.ir/rc/rc0
[ 10.634336] rc rc0: lirc_dev: driver sunxi-ir registered at minor = 0, raw IR receiver, no transmitter
[ 10.638896] input: sunxi-ir as /devices/platform/soc/7040000.ir/rc/rc0/input0
[ 10.665313] sunxi-ir 7040000.ir: initialized sunXi IR driver
[ 10.759284] Bluetooth: HCI UART driver ver 2.3
[ 10.759315] Bluetooth: HCI UART protocol H4 registered
[ 10.759320] Bluetooth: HCI UART protocol BCSP registered
[ 10.784040] Bluetooth: HCI UART protocol LL registered
[ 10.784067] Bluetooth: HCI UART protocol ATH3K registered
[ 10.796339] Bluetooth: HCI UART protocol Three-wire (H5) registered
[ 10.796713] Bluetooth: HCI UART protocol Intel registered
[ 10.797203] Bluetooth: HCI UART protocol Broadcom registered
[ 10.797282] Bluetooth: HCI UART protocol QCA registered
[ 10.797344] Bluetooth: HCI UART protocol Marvell registered
[ 10.852953] dwmac-sun8i 5030000.ethernet end0: renamed from eth0
[ 10.857896] usbcore: registered new interface driver cdc_ether
[ 10.867261] rndis_host 2-1:1.0 usb0: register 'rndis_host' at usb-5200000.usb-1, RNDIS device, 02:52:61:66:64:32
[ 10.868051] usbcore: registered new interface driver rndis_host
[ 10.878730] rndis_host 2-1:1.0 enu1: renamed from usb0
[ 10.949288] dwmac-sun8i 5030000.ethernet end0: Register MEM_TYPE_PAGE_POOL RxQ-0
[ 10.951285] dwmac-sun8i 5030000.ethernet end0: PHY [stmmac-0:01] driver [Generic PHY] (irq=POLL)
[ 10.951329] dwmac-sun8i 5030000.ethernet end0: No Safety Features support found
[ 10.951338] dwmac-sun8i 5030000.ethernet end0: No MAC Management Counters available
[ 10.951346] dwmac-sun8i 5030000.ethernet end0: PTP not supported by HW
[ 10.961036] dwmac-sun8i 5030000.ethernet end0: configuring for phy/rmii link modeand cat /sys/kernel/debug/clk/clk_summary
enable prepare protect duty hardware
clock count count count rate accuracy phase cycle enable
-------------------------------------------------------------------------------------------------------
iosc 1 1 0 16000000 300000000 0 50000 Y
osc32k 1 1 0 31250 300000000 0 50000 Y
osc32k-out 0 0 0 31250 300000000 0 50000 N
osc24M 15 15 0 24000000 0 0 50000 Y
ir 1 1 0 8000000 300000000 0 50000 Y
r-apb2 0 0 0 24000000 0 0 50000 Y
r-apb2-rsb 0 0 0 24000000 0 0 50000 N
r-apb2-i2c 0 0 0 24000000 0 0 50000 N
hdmi-slow 2 2 0 24000000 0 0 50000 Y
usb-phy3 1 1 0 24000000 0 0 50000 Y
usb-phy2 4 4 0 24000000 0 0 50000 Y
usb-phy1 1 1 0 24000000 0 0 50000 Y
usb-phy0 1 1 0 24000000 0 0 50000 Y
ts 0 0 0 24000000 0 0 50000 N
spi1 0 0 0 24000000 0 0 50000 N
spi0 0 0 0 24000000 0 0 50000 N
mmc1 0 0 0 400000 0 0 50000 N
nand1 0 0 0 24000000 0 0 50000 N
nand0 0 0 0 24000000 0 0 50000 N
avs 0 0 0 24000000 0 0 50000 N
apb2 1 1 0 24000000 0 0 50000 Y
bus-i2c4 0 0 0 24000000 0 0 50000 N
bus-i2c3 0 0 0 24000000 0 0 50000 N
bus-i2c2 0 0 0 24000000 0 0 50000 N
bus-i2c1 0 0 0 24000000 0 0 50000 N
bus-i2c0 0 0 0 24000000 0 0 50000 N
bus-uart5 0 0 0 24000000 0 0 50000 N
bus-uart4 0 0 0 24000000 0 0 50000 N
bus-uart3 0 0 0 24000000 0 0 50000 N
bus-uart2 0 0 0 24000000 0 0 50000 N
bus-uart1 0 0 0 24000000 0 0 50000 N
bus-uart0 1 1 0 24000000 0 0 50000 Y
pll-audio-hs 1 1 0 49142857 0 0 50000 Y
pll-audio-4x 0 0 0 49142857 0 0 50000 Y
pll-audio-2x 0 0 0 24571428 0 0 50000 Y
pll-audio-1x 2 2 0 12285714 0 0 50000 Y
audio-hub 2 2 0 12285714 0 0 50000 Y
audio-codec-4x 0 0 0 12285714 0 0 50000 N
audio-codec-1x 2 2 0 12285714 0 0 50000 Y
dmic 0 0 0 12285714 0 0 50000 N
spdif 0 0 0 12285714 0 0 50000 N
pll-de 1 1 0 600000000 0 0 50000 Y
g2d 0 0 0 600000000 0 0 50000 N
deinterlace 0 0 0 600000000 0 0 50000 N
de 2 2 0 600000000 0 0 50000 Y
wb-div 0 0 0 600000000 0 0 50000 Y
wb 0 0 0 600000000 0 0 50000 N
mixer1-div 0 0 0 600000000 0 0 50000 Y
mixer1 0 0 0 600000000 0 0 50000 N
mixer0-div 1 1 0 600000000 0 0 50000 Y
mixer0 1 1 0 600000000 0 0 50000 Y
pll-ve 0 0 0 600000000 0 0 50000 N
ve 0 0 0 600000000 0 0 50000 N
pll-video2 0 0 0 297000000 0 0 50000 N
pll-video2-4x 0 0 0 1188000000 0 0 50000 Y
pll-video1 0 0 0 297000000 0 0 50000 N
pll-video1-4x 0 0 0 1188000000 0 0 50000 Y
pll-video0 1 1 0 297000000 0 0 50000 Y
tve0 0 0 0 297000000 0 0 50000 N
tcon-tv1 0 0 0 297000000 0 0 50000 N
tcon-tv0 0 0 0 297000000 0 0 50000 N
tcon-top-tv0 0 0 0 297000000 0 0 50000 N
hdmi 1 1 0 297000000 0 0 50000 Y
pll-video0-4x 0 0 0 1188000000 0 0 50000 Y
pll-gpu 1 1 0 2400000000 0 0 50000 Y
gpu0 1 1 0 800000000 0 0 50000 Y
pll-periph1 0 0 0 600000000 0 0 50000 N
pll-periph1-2x 0 0 0 1200000000 0 0 50000 Y
pll-periph0 4 4 0 600000000 0 0 50000 Y
hdcp 0 0 0 600000000 0 0 50000 N
apb1 4 4 0 100000000 0 0 50000 Y
bus-keyadc 0 0 0 100000000 0 0 50000 N
bus-audio-hub 2 2 0 100000000 0 0 50000 Y
bus-audio-codec 1 1 0 100000000 0 0 50000 Y
bus-dmic 0 0 0 100000000 0 0 50000 N
bus-spdif 0 0 0 100000000 0 0 50000 N
bus-ths 1 1 0 100000000 0 0 50000 Y
bus-iommu 0 0 0 100000000 0 0 50000 N
bus-pwm 0 0 0 100000000 0 0 50000 N
ahb3 13 13 0 200000000 0 0 50000 Y
bus-hdcp 0 0 0 200000000 0 0 50000 N
bus-tve0 0 0 0 200000000 0 0 50000 N
bus-tve-top 0 0 0 200000000 0 0 50000 N
bus-tcon-tv1 0 0 0 200000000 0 0 50000 N
bus-tcon-tv0 1 1 0 200000000 0 0 50000 Y
bus-tcon-top 1 1 0 200000000 0 0 50000 Y
bus-hdmi 2 2 0 200000000 0 0 50000 Y
bus-otg 1 1 0 200000000 0 0 50000 Y
bus-ehci3 1 1 0 200000000 0 0 50000 Y
bus-ehci2 5 5 0 200000000 0 0 50000 Y
bus-ehci1 1 1 0 200000000 0 0 50000 Y
bus-ehci0 1 1 0 200000000 0 0 50000 Y
bus-ohci3 2 2 0 200000000 0 0 50000 Y
bus-ohci2 2 2 0 200000000 0 0 50000 Y
bus-ohci1 2 2 0 200000000 0 0 50000 Y
bus-ohci0 2 2 0 200000000 0 0 50000 Y
bus-ts 0 0 0 200000000 0 0 50000 N
bus-emac1 1 1 0 200000000 0 0 50000 Y
bus-emac0 0 0 0 200000000 0 0 50000 N
emac-25m 0 0 0 200000000 0 0 50000 N
bus-spi1 0 0 0 200000000 0 0 50000 N
bus-spi0 0 0 0 200000000 0 0 50000 N
bus-mmc2 0 0 0 200000000 0 0 50000 N
bus-mmc1 0 0 0 200000000 0 0 50000 N
bus-mmc0 0 0 0 200000000 0 0 50000 N
bus-nand 0 0 0 200000000 0 0 50000 N
psi-ahb1-ahb2 4 4 0 200000000 0 0 50000 Y
bus-dram 1 1 0 200000000 0 0 50000 Y
bus-psi 0 0 0 200000000 0 0 50000 N
bus-dbg 0 0 0 200000000 0 0 50000 N
bus-hstimer 0 0 0 200000000 0 0 50000 N
bus-dma 1 1 0 200000000 0 0 50000 Y
bus-ve 0 0 0 200000000 0 0 50000 N
bus-ce 0 0 0 200000000 0 0 50000 N
bus-gpu 1 1 0 200000000 0 0 50000 Y
bus-g2d 0 0 0 200000000 0 0 50000 N
bus-deinterlace 0 0 0 200000000 0 0 50000 N
bus-de 2 2 0 200000000 0 0 50000 Y
bus-wb 0 0 0 200000000 0 0 50000 N
bus-mixer1 0 0 0 200000000 0 0 50000 N
bus-mixer0 1 1 0 200000000 0 0 50000 Y
pll-periph0-2x 2 2 0 1200000000 0 0 50000 Y
mmc2 0 0 0 100000000 0 0 50000 N
mmc0 0 0 0 50000000 0 0 50000 N
pll-system-32k 0 0 0 32768 0 0 50000 Y
hdmi-cec 1 1 0 32768 0 0 50000 Y
ce 0 0 0 300000000 0 0 50000 N
gpu1 0 0 0 1200000000 0 0 50000 N
mbus 2 2 0 400000000 0 0 50000 Y
mbus-g2d 0 0 0 400000000 0 0 50000 N
mbus-nand 0 0 0 400000000 0 0 50000 N
mbus-ts 0 0 0 400000000 0 0 50000 N
mbus-ce 0 0 0 400000000 0 0 50000 N
mbus-ve 0 0 0 400000000 0 0 50000 N
mbus-dma 1 1 0 400000000 0 0 50000 Y
pll-ddr1 0 0 0 432000000 0 0 50000 N
pll-ddr0 1 1 0 1440000000 0 0 50000 Y
dram 1 1 0 1440000000 0 0 50000 Y
pll-cpux 1 1 0 1608000000 0 0 50000 Y
cpux 1 1 0 1608000000 0 0 50000 Y
cpux-apb 0 0 0 402000000 0 0 50000 Y
axi 0 0 0 804000000 0 0 50000 Y
osc12M 4 4 0 12000000 0 0 50000 Y
usb-ohci3 2 2 0 12000000 0 0 50000 Y
usb-ohci2 2 2 0 12000000 0 0 50000 Y
usb-ohci1 2 2 0 12000000 0 0 50000 Y
usb-ohci0 2 2 0 12000000 0 0 50000 Y
r-ahb 1 1 0 0 0 0 50000 Y
r-apb1 2 2 0 0 0 0 50000 Y
r-apb1-rtc 0 0 0 0 0 0 50000 Y
r-apb1-ir 1 1 0 0 0 0 50000 Y
r-apb1-twd 0 0 0 0 0 0 50000 Nbut still no wlan network interface.
Best regards, AR
warpme
commented
1 year ago qll - i have progress here:
[ 6.041712] brcmfmac mmc1:0001:1: loading /lib/firmware/brcm/brcmfmac-ap6330-sdio.tanix,tx6s.clm_blob failed with error -22
[ 6.070315] rc rc0: sunxi-ir as /devices/platform/soc/7040000.ir/rc/rc0
[ 6.070603] rc rc0: lirc_dev: driver sunxi-ir registered at minor = 0, raw IR receiver, no transmitter
[ 6.070818] input: sunxi-ir as /devices/platform/soc/7040000.ir/rc/rc0/input0
[ 6.076725] sunxi-ir 7040000.ir: initialized sunXi IR driver
[ 6.361365] brcmfmac mmc1:0001:1: loading /lib/firmware/brcm/brcmfmac-ap6330-sdio.clm_blob failed with error -22
[ 6.361403] brcmfmac mmc1:0001:1: Direct firmware load for brcm/brcmfmac-ap6330-sdio.clm_blob failed with error -22
[ 6.361410] brcmfmac mmc1:0001:1: Falling back to sysfs fallback for: brcm/brcmfmac-ap6330-sdio.clm_blob
[ 6.687773] brcmfmac_wcc: brcmf_wcc_attach: executing
[ 6.688877] brcmfmac: brcmf_c_process_clm_blob: no clm_blob available (err=-2), device may have limited channels available
[ 6.689233] brcmfmac: brcmf_c_preinit_dcmds: Firmware: BCM4330/4 wl0: Jan 23 2013 17:46:35 version 5.90.195.114 FWID 01-cafa6b3eroot@Myth-Frontend-0200252ec1ea:~ # ip link
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue qlen 1000
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq qlen 1000
link/ether 02:00:25:2e:c1:ea brd ff:ff:ff:ff:ff:ff
3: wlan0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop qlen 1000
link/ether e0:76:d0:4f:0e:e4 brd ff:ff:ff:ff:ff:ffI uploaded new versions of images with ap6330 support. I think we may close this ticket. Many thx for your's support!
arg7
commented
1 year ago Thank you for your hard work.
Saluti, Ing. Andrey Romanov CompEd Software Design srl
On Tue, 18 Apr 2023 at 09:32, Piotr Oniszczuk @.***> wrote:
I uploaded new versions of images with ap6330 support. I think we may close this ticket. Many thx for your's support!
— Reply to this email directly, view it on GitHub, or unsubscribe. You are receiving this because you were mentioned.Message ID: @.***>
I have issue with the latest MiniArch on Tanix TX6S with SP6330 wifi chip.
SDIO doesn't show up in dmesg, modprobe brcmfmac does nothing.
For the rest, MiniArch works perfectly.
Here is log:
U-Boot SPL 2021.04 (Feb 25 2023 - 15:19:32 +0100) DRAM: 4096 MiB Failed to set core voltage! Can't set CPU frequency Trying to boot from MMC1 NOTICE: BL31: v2.8(debug):v12.13.0-v33-Pre-1175-g91e3da68e6-5-g0518a270 NOTICE: BL31: Built : 15:19:28, Feb 25 2023 NOTICE: BL31: Detected Allwinner H616 SoC (1823) NOTICE: BL31: Found U-Boot DTB at 0x4a085a28, model: Tanix TX6s INFO: ARM GICv2 driver initialized INFO: Configuring SPC Controller INFO: PMIC: Probing AXP305 on RSB WARNING: PMIC: No regulators DT node, skipping setup INFO: BL31: Platform setup done INFO: BL31: Initializing runtime services INFO: BL31: cortex_a53: CPU workaround for 855873 was applied INFO: BL31: cortex_a53: CPU workaround for 1530924 was applied INFO: PSCI: Suspend is unavailable INFO: BL31: Preparing for EL3 exit to normal world INFO: Entry point address = 0x4a000000 INFO: SPSR = 0x3c9 INFO: Changed devicetree.
U-Boot 2021.04 (Feb 25 2023 - 15:19:32 +0100) Allwinner Technology
CPU: Allwinner H616 (SUN50I) Model: Tanix TX6s I2C: ready DRAM: 3 GiB MMC: mmc@4020000: 0, mmc@4022000: 1 Loading Environment from FAT... Card did not respond to voltage select! : -110 In: serial@5000000 Out: serial@5000000 Err: serial@5000000 Net: No ethernet found. starting USB... No working controllers found Hit any key to stop autoboot: 0 switch to partitions #0, OK mmc0 is current device Scanning mmc 0:1... Found U-Boot script /boot.scr 1501 bytes read in 2 ms (732.4 KiB/s) Executing script at 4fc00000 32115200 bytes read in 2665 ms (11.5 MiB/s) Failed to load '/h616_dtb' 27993 bytes read in 9 ms (3 MiB/s) 7630304 bytes read in 636 ms (11.4 MiB/s) Moving Image from 0x40080000 to 0x40200000, end=42140000 #1 Flattened Device Tree blob at 4fa00000 Booting using the fdt blob at 0x4fa00000 Loading Ramdisk to 498b9000, end 49fffde0 ... OK Loading Device Tree to 00000000498af000, end 00000000498b8fff ... OK
Starting kernel ...
:: running early hook [udev] Starting systemd-udevd version 253-1-arch :: running hook [udev] :: Triggering uevents... :: running hook [keymap] :: Loading keymap...kbd_mode: KDSKBMODE: Inappropriate ioctl for device done. :: performing fsck on '/dev/mmcblk0p2' ROOT: clean, 31331/1866384 files, 332874/3811584 blocks :: mounting '/dev/mmcblk0p2' on real root :: running cleanup hook [udev]
Welcome to Arch Linux ARM!
[ OK ] Created slice Slice /system/getty. [ OK ] Created slice Slice /system/modprobe. [ OK ] Created slice Slice /system/serial-getty. [ OK ] Created slice User and Session Slice. [ OK ] Started Dispatch Password …ts to Console Directory Watch. [ OK ] Started Forward Password R…uests to Wall Directory Watch. [UNSUPP] Starting of Arbitrary Exec…m Automount Point unsupported. [ OK ] Reached target Local Encrypted Volumes. [ OK ] Reached target Local Integrity Protected Volumes. [ OK ] Reached target Path Units. [ OK ] Reached target Remote File Systems. [ OK ] Reached target Slice Units. [ OK ] Reached target Swaps. [ OK ] Reached target Local Verity Protected Volumes. [ OK ] Listening on Device-mapper event daemon FIFOs. [ OK ] Listening on Process Core Dump Socket. [ OK ] Listening on Journal Socket (/dev/log). [ OK ] Listening on Journal Socket. [ OK ] Listening on Network Service Netlink Socket. [ OK ] Listening on udev Control Socket. [ OK ] Listening on udev Kernel Socket. Mounting POSIX Message Queue File System... Mounting Kernel Debug File System... Mounting Kernel Trace File System... Mounting Temporary Directory /tmp... Starting Create List of Static Device Nodes... Starting Load Kernel Module configfs... Starting Load Kernel Module dm_mod... Starting Load Kernel Module drm... Starting Load Kernel Module fuse... Starting Load Kernel Module loop... Starting Journal Service... Starting Generate network …ts from Kernel command line... Starting Remount Root and Kernel File Systems... Starting Apply Kernel Variables... Starting Coldplug All udev Devices... [ OK ] Mounted POSIX Message Queue File System. [ OK ] Mounted Kernel Debug File System. [ OK ] Mounted Kernel Trace File System. [ OK ] Mounted Temporary Directory /tmp. [ OK ] Finished Create List of Static Device Nodes. [ OK ] Finished Load Kernel Module configfs. [ OK ] Started Journal Service. [ OK ] Finished Load Kernel Module dm_mod. [ OK ] Finished Load Kernel Module drm. [ OK ] Finished Load Kernel Module fuse. [ OK ] Finished Load Kernel Module loop. [ OK ] Finished Generate network units from Kernel command line. [ OK ] Finished Remount Root and Kernel File Systems. [ OK ] Finished Apply Kernel Variables. [ OK ] Reached target Preparation for Network. Mounting Kernel Configuration File System... Starting Flush Journal to Persistent Storage... Starting Load/Save OS Random Seed... Starting Create Static Device Nodes in /dev... [ OK ] Mounted Kernel Configuration File System. [ OK ] Finished Coldplug All udev Devices. [ OK ] Finished Flush Journal to Persistent Storage. [ OK ] Finished Create Static Device Nodes in /dev. [ OK ] Reached target Preparation for Local File Systems. Starting Rule-based Manage…for Device Events and Files... [ OK ] Started Rule-based Manager for Device Events and Files. Starting Network Configuration... [ OK ] Found device /dev/ttyS0. [ OK ] Started Network Configuration. [ OK ] Found device /dev/disk/by-label/BOOT. Mounting /boot... [ OK ] Mounted /boot. [ OK ] Reached target Local File Systems. [ OK ] Reached target Hardware activated USB gadget. Starting Create Volatile Files and Directories... [ OK ] Finished Load/Save OS Random Seed. [ OK ] Reached target Sound Card. [ OK ] Listening on Load/Save RF …itch Status /dev/rfkill Watch. [ OK ] Finished Create Volatile Files and Directories. Starting Network Name Resolution... Starting Network Time Synchronization... Starting Record System Boot/Shutdown in UTMP... [ OK ] Finished Record System Boot/Shutdown in UTMP. [ OK ] Started Network Time Synchronization. [ OK ] Reached target System Time Set. [ OK ] Started Network Name Resolution. [ OK ] Reached target Network. [ OK ] Reached target Host and Network Name Lookups. [ OK ] Reached target System Initialization. [ OK ] Started Refresh existing P…f archlinux-keyring regularly. [ OK ] Started Daily verification of password and group files. [ OK ] Started Daily Cleanup of Temporary Directories. [ OK ] Reached target Timer Units. [ OK ] Listening on D-Bus System Message Bus Socket. [ OK ] Reached target Socket Units. [ OK ] Reached target Basic System. Starting D-Bus System Message Bus... [ OK ] Started OpenSSH Daemon. Starting User Login Management... Starting Permit User Sessions... [ OK ] Finished Permit User Sessions. [ OK ] Started Getty on tty1. [ OK ] Started Serial Getty on ttyS0. [ OK ] Reached target Login Prompts. [ OK ] Started User Login Management. [ OK ] Started D-Bus System Message Bus. [ OK ] Reached target Multi-User System. [ OK ] Reached target Graphical Interface.
Arch Linux 6.2.0 (ttyS0)
alarm login:
Originally posted by @arg7 in https://github.com/warpme/minimyth2/issues/10#issuecomment-1451470824