lexmulya
commented
2 days ago Uboot log when loading android `U-Boot SPL 2024.01 (Jun 13 2024 - 15:40:46 +0300) DRAM: 128 MiB [82]HELLO! BOOT0 is starting! [85]BOOT0 commit : 3ae35eb [87]set pll start [90]periph0 has been enabled [93]set pll end [95]unknow PMU [96]unknow PMU [98]PMU: AXP1530 [100]dram return write ok [103]board init ok [104]DRAM BOOT DRIVE INFO: V0.648 [108]the chip id is 0x5c00 [110]chip id check OK [114]DRAM_VCC set to 1200 mv [117]DRAM CLK =600 MHZ [119]DRAM Type =7 (3:DDR3,4:DDR4,7:LPDDR3,8:LPDDR4) [127]Actual DRAM SIZE =1536 M [130]DRAM SIZE =1536 MBytes, para1 = 30fa, para2 = 6001000, dram_tpr13 = 26061 [143]DRAM simple test OK. [145]rtc standby flag is 0x0, super standby flag is 0x0 [151]dram size =1536 [154]card no is 2 [156]sdcard 2 line count 8 [158][mmc]: mmc driver ver 2021-10-12 13:56 [163][mmc]: b mmc 2 bias 4 [171][mmc]: Wrong media type 0x0, but host sdc2, try mmc first [177][mmc]: Try MMC card 2 [223][mmc]: RMCA OK! [228][mmc]: MMC 5.0 [230][mmc]: HSSDR52/SDR25 8 bit [233][mmc]: 50000000 Hz [235][mmc]: 7456 MB [237][mmc]: SD/MMC 2 init OK!!! [318]Loading boot-pkg Succeed(index=0). [322][mmc]: b mmc 2 bias 4 [324]Entry_name = u-boot [334]Entry_name = monitor [338]Entry_name = dtbo [341]Entry_name = dtb [345]tunning data addr:0x4a0003e8 [348]Jump to second Boot. NOTICE: BL3-1: v1.0(debug):05d6c57 NOTICE: BL3-1: Built : 13:35:35, 2021-10-28 NOTICE: BL3-1 commit: 8 NOTICE: cpuidle init version V1.0 ERROR: Error initializing runtime service tspd_fast NOTICE: BL3-1: Preparing for EL3 exit to normal world NOTICE: BL3-1: Next image address = 0x4a000000 -OTICE: BL3-1: Next image spsr = 0x1d3
U-Boot 2018.05 (Dec 04 2023 - 17:33:48 +0800) Allwinner Technology
[00.428]CPU: Allwinner Family [00.431]Model: sun50iw9 I2C: ready [00.435]DRAM: 1.5 GiB [00.438]Relocation Offset is: 55ebf000 [00.482]secure enable bit: 0 [00.485]pmu_axp152_probe pmic_bus_read fail [00.489]PMU: AXP1530 [00.494]CPU=1008 MHz,PLL6=600 Mhz,AHB=200 Mhz, APB1=100Mhz MBus=400Mhz [00.502]drv_disp_init [00.532]__clk_enable: clk is null. [00.538]drv_disp_init finish [00.541]gic: sec monitor mode [00.570]flash init start [00.573]workmode = 0,storage type = 2 [00.576]MMC: 2 [00.577][mmc]: mmc driver ver uboot2018:2021-07-19 14:09:00 [00.584][mmc]: get sdc_type fail and use default host:tm4. [00.595][mmc]: SUNXI SDMMC Controller Version:0x40502 [00.648][mmc]: Best spd md: 3-HS200/SDR104, freq: 4-150000000, Bus width: 8 [00.654]sunxi flash init ok [00.658]Loading Environment from SUNXI_FLASH... OK [00.668]usb burn from boot delay time 0 weak:otg_phy_config [00.682]usb prepare ok [01.485]overtime [01.489]do_burn_from_boot usb : no usb exist [01.493]boot_gui_init:start FAT: Misaligned buffer address (9be7b598) 32 bytes read in 4 ms (7.8 KiB/s) [01.777]boot_gui_init:finish [01.780]bmp_name=bootlogo.bmp 3686456 bytes read in 31 ms (113.4 MiB/s) [01.825][mmc]: delete mmc-hs400-1_8v from dtb [01.832]update dts Unrecognized filesystem type [01.843]load file(ULI/factory/rootwait init.txt) error. Unrecognized filesystem type [01.858]load file(ULI/factory/snum.txt) error. [01.862]name in map mac Unrecognized filesystem type [01.874]load file(ULI/factory/wifi_mac.txt) error. Unrecognized filesystem type [01.888]load file(ULI/factory/bt_mac.txt) error. Unrecognized filesystem type [01.901]load file(ULI/factory/selinux.txt) error. Unrecognized filesystem type [01.915]load file(ULI/factory/specialstr.txt) error. [01.926]update part info [01.949]update bootcmd [01.951]No ethernet found. Hit any key to stop autoboot: 0 [02.182]Starting kernel ...`
Hello.
I am the owner of a strange x96q clone, it looks like lpddr3+emmc. I tried MiniMyth2-armv8-master-13.2.1.r130-board-h313.x96_q_lpddr3_v1.3-SD-Image.img and MiniMyth2-armv8-master-13.2.1.r130-board-h313.x96_q_lpddr3-SD-Image. img and they both do not load to the kernel.
I get the following log `U-Boot SPL 2024.04 (May 18 2024 - 02:16:28 +0200) DRAM: 2048 MiB Trying to boot from MMC1 NOTICE: BL31: v2.10.0 (debug):v13.2.0-3-ga1bb0b907-dirty NOTICE: BL31: Built : 02:16:23, May 18 2024 NOTICE: BL31: Detected Allwinner H616 SoC (1823) NOTICE: BL31: Found U-Boot DTB at 0x4a0ae9d8, model: hechuang,x96-q LPDDR3 v1.3 INFO: ARM GICv2 driver initialized INFO: Configuring SPC Controller INFO: PMIC: Probing AXP305 on RSB ERROR: RSB: set run-time address: 0x10003 INFO: Could not init RSB: -65539 INFO: BL31: Platform setup done INFO: BL31: Initializing runtime services INFO: BL31: cortex_a53: CPU workaround for erratum 855873 was applied INFO: BL31: cortex_a53: CPU workaround for erratum 1530924 was applied INFO: PSCI: Suspend is unavailable INFO: BL31: Preparing for EL3 exit to normal world INFO: Entry point address = 0x4a000000 INFO: SPSR = 0x3c9 INFO: Changed devicetree.
U-Boot 2024.04 (May 18 2024 - 02:16:28 +0200) Allwinner Technology
CPU: Allwinner H616 (SUN50I) Model: hechuang,x96-q LPDDR3 v1.3 DRAM: 2 GiB (effective 4.7 EiB)`
The memory chip I have installed is h9tq64aaetac I booted into the built-in android and downloaded the DTB file x96q.dtb.gz
If you have free time, I ask for your help. I'm sorry for my English.