gpsd freezes when using Direwolf on Raspberry Pi -- Raspbian Jesse

[petitnj]

Run GPSD on Raspberry Pi to pass time and location to Direwolf 1.5. Starts up and runs for a few hours but then "GPS timeout" occurs. Direwolf continues but the time is not updated. Using a USB based GPS receiver from Adafruit. NTP finds the GPS input just fine and updates for a while. No indication on any of the direwolf or system logs.

The only way to correct is a reboot of the Raspberry Pi.

Anyone have any experience with this?

[dranch]

Hello Petitnj, It's unclear what your ask is here but this doesn't sound like a bug per-se as there haven't been any other reports of GPS issues with Direwolf. To get better support, please close this issue and create a new thread on direwolf_packet@yahoogroups.com. In that new thread, maybe you can answer some of the following questions to get you going:

Do you feel that Direwolf is crashing gpsd? Maybe you can shutdown Direwolf and just run "gpstl" or "cgps" for several hours and see if your system continues to display GPS data. If it does, I would then recommend to try again with Direwolf but leave your radio off. The inability for the system to TX would isolate if your data transmissions are creating any RFI issues into the GPS and/or your Raspberry Pi.

[petitnj]

Do you feel that Direwolf is crashing gpsd?

No Direwolf shoulders on even when no further GPS messages are arriving via the gpsd.socket.

Maybe you can shutdown Direwolf and just run "gpstl" or "cgps" for several hours and see if your system continues to display GPS data.

Again this is very difficult to reproduce the effect. I suspect the USB driver is freezing up. When GPS freezes, I try

sudo service gpsd stop sudo service gpsd start

and gps input is still frozen. Only a reboot cleared the USB line to start sending data again.

Before GPSD, I ran Direwolf as a fixed location gateway/digpeater/weather node. It runs without fail for weeks.

I will try the RFI problem if the freeze up persists. I do have the  VHF antenna 30 feet up over the GPS receiver and I am running the transmitter at low power (about 5 watts).

Thanks for the ideas. I am pretty sure it is not a problem with Direwolf, but was hoping that someone who is setting up their system may have run into the same problem

Thanks for the great software and  I will keep working on the problem. I have an article ready for QST with Direwolf running on the RPi. To complete the system, the editors suggested that I add GPS. I hope that this freeze up problem can be solved and I can resubmit the article.

Thanks,

Noel Petit WB0VGI Harris, MN

[wb2osz]

I did a search for gpsd timeout raspberry pi, and found a couple related items:

https://raspberrypi.stackexchange.com/questions/30183/gpsd-data-receiving-issues/67767 https://www.raspberrypi.org/forums/viewtopic.php?p=712458

Can you provide more details? What is the exact GPS model? I don't see a USB GPS from Adafruit. What does gpsd configuration look like? What does direwolf config file look like? Does the same thing happen when direwolf is not involved? You already mentioned that the system log files did not contain anything interesting.

It might be better to continue with email rather than here due to the size of information.

wb2osz \ comcast \ net

[petitnj]

Using the Adafruit GPS ultimate breakout connected to the RPi with the GPS external antenna, RP-SMA to uFL/u.FL/IPX/IPEX RF Adapter Cable, and the USB to Serial Cable. This GPS system has proven years of success in our magnetometer systems for PC timing. Additionally the direwolf.conf has the standard lines for GPSD

GPSD TBEACON every=30 symbo="digi" power=50 height=20 gain=4 comment="Harris, MN" WIDE1-1,WIDE2-1 SMARTBEACON 60 2:00 5 10:00 0:45 30 255

I entered this thread to see if anyone else had the problem. With the recent library updates (Feb 5 2019) of the operating system, the freeze up of gpsd has disappeared (knock on wood). I am closing this thread for now and will reopen if it reappears.