search

zhelezyaka / opentx

Automatically exported from code.google.com/p/opentx
0 stars 0 forks source link

Switch type selection, Custom Function enhancements #145

Open GoogleCodeExporter opened 9 years ago

GoogleCodeExporter commented 9 years ago 
Which board (stock / gruvin9x / sky9x / Taranis) are you using?
Stock Taranis batch 1, gimbals replaced, 2p switch moved from rhs to lhs

What is your openTx FW version?
Latest 19/09/2013

What is your openTx EEPROM version?
Latest 19/09/2013

What steps will reproduce the problem?
Read below

I've been using the taranis for a while and I have the following 
issues/enhancement requests
1) Modify the "play sound" cf to allow a 0.5 s delay when you flip the switch 
or give priority to the next cf and interupt the current one if the trigger for 
the same switch is selected within 0.5 seconds. For example if I have a cf on 
all 3p switch and I switch from p0 to p2 the tx to effectively play only the cf 
on p2.

2) companion9x simulator to be able to select if the SH switch should spring 
back (I moved mine from the right to left side) i know a few others did the same

3) the user to he able to select if I he/she want to run cf while the tx starts 
up. basically I don't want the tx to play any switch position sounds (or select 
which that can play) when the tx boots up.cheerscf: custom function

Original issue reported on code.google.com by cklea...@gmail.com on 19 Sep 2013 at 6:02

GoogleCodeExporter commented 9 years ago 
[deleted comment]
GoogleCodeExporter commented 9 years ago 
1 and 3 are already implemented for next major release. 
2 will not be considered as swapping switches breaks existing functionality. 
If/when done it will be more complete than this and allow selecting what type 
each switch is.

Original comment by bernet.a...@gmail.com on 23 Sep 2013 at 2:30

GoogleCodeExporter commented 9 years ago 
[deleted comment]
GoogleCodeExporter commented 9 years ago 
Putting FrSky in CC to inform from users' request.

Implementation would be a "Hardware" radio setup page with among others a 
"Switches" section where the user can select for each of SA-SH if a 3-position, 
2-position or momentary switch is installed (taking hardware capabilities into 
consideration of course).

Original comment by bernet.a...@gmail.com on 23 Sep 2013 at 3:19

GoogleCodeExporter commented 9 years ago 
Issue 35 has been merged into this issue.

Original comment by bernet.a...@gmail.com on 23 Sep 2013 at 3:29

GoogleCodeExporter commented 9 years ago 
Issue 126 has been merged into this issue.

Original comment by bernet.a...@gmail.com on 23 Sep 2013 at 3:45

GoogleCodeExporter commented 9 years ago

Original comment by bernet.a...@gmail.com on 23 Sep 2013 at 3:46

GoogleCodeExporter commented 9 years ago 
In addition, if physically possible, it would be nice if, on 3 position 
switches, the up position and down position could be enabled simultaneously.  

Further explanation:
Presume you have a 3-way switch. Up is obviously up, down is down, centered is 
neither up nor down.  

Now think paralleling the switch's two positions with momentary push-buttons.  
No button pressed yields center position.  Button A yields switch up.  Button B 
yields switch down. Both buttons pressed at the same time yields both up and 
down conditions at the same time, but center position off.

Even without adding short press and long options, this would make some 
interesting input control possible.

Original comment by wre...@gmail.com on 18 Oct 2013 at 3:01

GoogleCodeExporter commented 9 years ago 
Swapping the Trainer switch to the RH side is for me a must (mode 2 flyer) but 
I don't want to extend the wiring and void my warranty if there is a chance in 
the near future for a software solution.

Original comment by gadgetma...@gmail.com on 19 Oct 2013 at 5:19