Just passing by for a few questions!

[Durahl]

Greetings!

I just came across your MOD over on the Voron MODs page and was quite intrigued because of my Setup since I'm running even heavier than Stock LDO-42STH60-3004MAC (S40) Stepper Motors but before considering the change I was wondering about a few things:

• I don't think it does but just to make sure does this MOD in ANY kind shift the X / Y location of the Belts? 🤔 I'm asking because my V2.4 uses a CNCed Deck Panel with low clearance Z-Belt Passthroughs:

• When using a Y-Axis Cable Chain - Doesn't this MOD limit the Gantry's capability of reaching the Y0 location? In my Stock Setup the Bend in the Cable Chain easily touches the Belt at the location where your Upper Gantry Pulley would reside. Are you using a different XY Cable Chain Bridge or different than BOM Spec Cable Chains? Asking because of my Tool Head Filament Cutter Pin being located in the B Drive Idler and in need of reaching Y3:

• Reusing the old Belts doesn't seem to be an option as they'll not be having the short, right? 🤨 ( the BOM makes a 50% note which I guess is hinting at this issue? )

Thanks in advance... Cheers!

[Durahl]

Ah yea... Found a bit of a Clerance Issue with the Stock Z-Idler Pulley clipping into your Belt attachment Ppoint:

[zzp8202]

Hello Durahl

Thank you let me know somebody like my mod.

1. It should be compatibility with you CNCed Deck Panel.

2. Also, it compatibility with your Tool Head Filament Cutter Pin.

3. Yes, you should use a new belt to replace the old belt, because we need a longer belt.

4. Clerance Issue is fixed on STL file.

Durahl @.***> 于2024年8月20日周二 00:06写道：

Greetings!

I just came across your MOD over on the Voron MODs page and was quite intrigued because of my Setup since I'm running even heavier than Stock LDO-42STH60-3004MAC (S40) Stepper Motors https://i.imgur.com/NWVWd6k.jpeg but before considering the change I was wondering about a few things:

-

I don't think it does but just to make sure does this MOD in ANY kind shift the X / Y location of the Belts? 🤔 I'm asking because my V2.4 uses a CNCed Deck Panel with low clearance Z-Belt Passthroughs: IewudSF.jpg (view on web) https://github.com/user-attachments/assets/fb6dbced-7b6c-4500-bc61-a1fe0465f45a

When using a Y-Axis Cable Chain - Doesn't this MOD limit the Gantry's capability of reaching the Y0 location? In my Stock Setup the Bend in the Cable Chain easily touches the Belt at the location where your Upper Gantry Pulley would reside. Are you using a different XY Cable Chain Bridge or different than BOM Spec Cable Chains? Asking because of my Tool Head Filament Cutter Pin being located in the B Drive Idler and in need of reaching Y3: aJaOr42.jpg (view on web) https://github.com/user-attachments/assets/f4eb244b-53db-461f-aeb8-f1b282ce59ea

Reusing the old Belts doesn't seem to be an option as they'll not be having the short, right? 🤨 ( the BOM makes a 50% note which I guess is hinting at this issue? )

Thanks in advance... Cheers!

— Reply to this email directly, view it on GitHub https://github.com/zzp8202/Double_GEAR_ratio_Z/issues/1, or unsubscribe https://github.com/notifications/unsubscribe-auth/ASQDC2YU5LZDYTJ76P6U27DZSIJYRAVCNFSM6AAAAABMYEFRRWVHI2DSMVQWIX3LMV43ASLTON2WKOZSGQ3TGNZRGAZDQMY . You are receiving this because you are subscribed to this thread.Message ID: @.***>

-- 。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。 Billy zhang @.***