issues
search
Blue-Smoke-Electronics
/
Ember
16
stars
5
forks
source link
issues
Newest
Newest
Most commented
Recently updated
Oldest
Least commented
Least recently updated
order parts list
#219
youngsfamilyphone
opened
4 months ago
2
add hole in encloser so that charging led is vissible
#218
simenhs
closed
1 year ago
1
battery is not charged fast enought when the battery level is below 2.5V
#217
simenhs
closed
1 year ago
6
remove vbat and vboost ground planes
#216
simenhs
closed
1 year ago
1
usb disconnects when drawing more than 800 mA
#215
simenhs
closed
1 year ago
8
is usb charging screen nessesary?
#214
simenhs
closed
1 year ago
2
mark programing header orienation in silckscreen
#213
simenhs
closed
1 year ago
1
voltage doesn't reach 15V
#212
simenhs
closed
1 year ago
1
battery charger gets hot, and charging drops down to 300mA
#211
simenhs
closed
1 year ago
1
high power draw when below 3.1V on battery
#210
simenhs
closed
1 year ago
5
charger preconditon prevent battery charging
#209
simenhs
closed
1 year ago
4
very short time before poweroff
#208
simenhs
closed
1 year ago
1
does battery empty symbol show up?
#207
simenhs
closed
1 year ago
2
version in seriall terminal
#206
simenhs
opened
1 year ago
0
deviche should power of when powerbutton is pressed in, not relesed. People hold down the powerbotton because thats how they usualy works
#205
simenhs
closed
1 year ago
1
replace eproom with 2mB one
#204
simenhs
closed
1 year ago
2
Add magnets to the side of the encloser to connect multiple embers togther
#203
simenhs
closed
1 year ago
1
freezes when writing to flash
#202
simenhs
closed
1 year ago
3
check out LIX controll, should this be implemented?
#201
simenhs
opened
1 year ago
0
add smooting filter on messurments in display
#200
simenhs
closed
1 year ago
1
17.5V is not enogut on 18V rail
#199
simenhs
closed
1 year ago
3
Add cc indicator to display
#198
simenhs
closed
1 year ago
1
add back 10k resistor between 3v3 and flash CS pin
#197
simenhs
closed
1 year ago
10
q10 (drinving npn) gets hot
#196
simenhs
closed
1 year ago
5
Q10 connected to booster out, not 18V
#195
simenhs
closed
1 year ago
1
C25334 is not a good 0.1R resistor
#194
simenhs
closed
1 year ago
1
replace 2SCR574D3TL1
#193
simenhs
closed
1 year ago
1
replace AONR21117
#192
simenhs
closed
1 year ago
1
replace TPH3R704PC,LQ
#191
simenhs
closed
1 year ago
1
opamp is not connected to 18V
#190
simenhs
closed
1 year ago
1
capasity calculation is bad
#189
simenhs
closed
1 year ago
2
encoder holes need to be larger - 10mm
#188
simenhs
closed
1 year ago
1
encoder holes to small
#187
simenhs
closed
1 year ago
1
make encoder pads larger to make soldering easyer by hand
#186
simenhs
closed
1 year ago
1
move display solder pads 2mm away form encoders
#185
simenhs
closed
1 year ago
1
very high power loss when driving display backlight form 18V
#184
simenhs
closed
1 year ago
1
power button hole is not rightly alligned
#183
simenhs
closed
1 year ago
2
do not enter charging mode when started with usb
#182
simenhs
closed
1 year ago
1
Do not always power on
#181
simenhs
closed
1 year ago
1
change partnumber on battery holder to part without polarity
#180
simenhs
closed
1 year ago
1
change 5V to 18V and connect opamp power to 18V
#179
simenhs
closed
1 year ago
6
can booster voltage be regulated closer to linreg voltage?
#178
simenhs
closed
1 year ago
1
bipolar gate driver ic not working. replace with mosfet driven one
#177
simenhs
closed
1 year ago
2
only show all 5 battery bars when battery is 100% charged
#176
simenhs
closed
1 year ago
1
replace MBR12100LPS-TP with SVT10100UB_R2_00001 ( larger footprint)
#175
simenhs
closed
1 year ago
1
Differential input voltage is max 2V on opamp.
#174
simenhs
closed
1 year ago
2
reduce voltage divider on output voltage sens to increase resolution of adc. 10k 2k might be good
#173
simenhs
closed
1 year ago
1
voltage is messured 0.1v to low from 4.4v and up
#172
simenhs
closed
1 year ago
4
replace ZXGD3009E6TA with ZXGD3009DYTA
#171
simenhs
closed
1 year ago
2
Design and optionally include/sell as a option a cover
#170
Kagee
opened
1 year ago
1
Next