Breath4Life controller issues

Breath4Life / controller

5 stars 1 forks source link

issues

Newest

Newest Most commented Recently updated Oldest Least commented Least recently updated

MOTOR02 error after 20 minutes of operation

#64 anpar opened 4 years ago
7
SENSO14 error message instead of PATCO15 during calibration

#63 anpar opened 4 years ago
0
Respiratory frequency check (cc #61)

#62 anpar opened 4 years ago
0
abnormal frequency alarm

#61 cassiersg opened 4 years ago
0
Project licence

#60 anpar opened 4 years ago
4
Max temperatures

#59 anpar closed 4 years ago
1
Buzzer welcome beep

#58 anpar opened 4 years ago
3
criticality of temperature errors

#57 cassiersg opened 4 years ago
4
MUTE crops welcome_wait_cal

#56 cassiersg closed 4 years ago
0
MUTE not erased in welcome_wait_cal

#55 cassiersg closed 4 years ago
0
prevent Ack critical_failure

#54 cassiersg closed 4 years ago
0
2nd round of clean-up on main_task.c/h

#53 anpar closed 4 years ago
1
Clean-up display.c

#52 anpar closed 4 years ago
1
LED fix (probably main task)

#51 cmomin closed 4 years ago
0
[MOTOR TASK]: send notification to main task for different error cases in running mode

#50 cmomin opened 4 years ago
0
[MOTOR] Add proper notification for low and medium error in calibration

#49 cmomin opened 4 years ago
0
Add MAIN_NOTIF_CALIB_FAILED in main task

#48 cmomin closed 4 years ago
1
Acknowledge a functional state of the sensors before starting a movement

#47 cmomin closed 4 years ago
1
Allow mute of critical failure alarm

#46 anpar closed 4 years ago
2
differential flow meter

#45 cassiersg opened 4 years ago
0
handle error in calibration for motor

#44 cassiersg closed 4 years ago
1
modular menu

#43 cassiersg closed 4 years ago
0
confirm change button

#42 cassiersg closed 4 years ago
0
Reduce delay at the begining of a breath cycle when moving from stop to run

#41 anpar opened 4 years ago
0
Target volume check

#40 cmomin closed 4 years ago
3
Buzzer welcome beep

#39 anpar closed 4 years ago
0
investigate micro-stepping to reduce noise

#38 cassiersg opened 4 years ago
0
main task: handle motor error

#37 cassiersg closed 4 years ago
2
handle overpressure motor

#36 cassiersg closed 4 years ago
0
Revised LCD display

#35 anpar closed 4 years ago
0
SFM3300 error handling/volume validity

#34 anpar opened 4 years ago
1
SFM3300-D CRC calculation not working

#33 anpar closed 4 years ago
0
do not exceed max position

#32 cassiersg closed 4 years ago
0
[MOTOR TASK]: modify drift handling

#31 cmomin opened 4 years ago
1
plateau: investigate real stop

#30 cassiersg opened 4 years ago
0
motor HAL: always send MOVEMENT_FINISHED

#29 cassiersg closed 4 years ago
0
motor HAL stop_anticipated

#28 cassiersg closed 4 years ago
0
Open door switch

#27 anpar closed 4 years ago
3
PEEP pressure calculation

#26 anpar closed 4 years ago
1
Replace instantaneous pressure display by plateau pressure

#25 anpar closed 4 years ago
1
Read motor driver error pin

#24 anpar closed 4 years ago
2
Write total_operating_time and cycles_numbers to EEPROM every 5 min #7

#23 jonadem closed 4 years ago
4
Specify LCD behaviour when globalState is critical_failure

#22 anpar closed 4 years ago
3
Temperature sensor output variablity + fix my ugly code

#21 anpar closed 4 years ago
0
Update to manage different timers for system ticks (part 2/2)

#20 Stivy13 closed 4 years ago
0
Reading power level

#19 anpar closed 4 years ago
0
Reading battery level

#18 anpar closed 4 years ago
0
Buzzer -3dB

#17 anpar closed 4 years ago
4
Low-level motor control: table-based acceleration (fuck divisions)

#16 anpar opened 4 years ago
0
Motor control pressure feedback: level 2

#15 anpar opened 4 years ago
1