The Elelabs Firmware Update Utility is a basic Python 3 script to flash the the firmware inside a range of Elelabs Zigbee and Thread products to a newer version.
Currently sold supported products based on Silicon Labs microcontrollers:
Previously sold supported products based on Silicon Labs microcontrollers:
Disclaimer: This utility should also work with other generic EZSP (EmberZNet Serial Protocol) or Spinel (Openthread Serial Protocol) based adapters and modules from other vendors, however firmwares for products not from Elelabs are not provided here and there is no guarantees that that it will work with non-Elelabs products. Be wanted that you may void your warranty and even brick your adapter if the firmware update is not supported by your mnaufacturer.
Download or clone the repository
Get your Python3 ready
Install the required packages using the pip
utility
pip3 install -r requirements.txt
Connect your Elelabs Zigbee/Thread Product to your PC or Raspberry Pi
Find out the Serial port number of the Elelabs Zigbee/Thread Product
/dev/ttyAMA0
/dev/ttyUSB0
(the number 0 may be different)COM1
(the number 1 may be different)Launch the probe
command to check if everything is working as expected
python3 Elelabs_EzspFwUtility.py probe -p /dev/ttyUSB0
only for Elelabs products
The ele_update
is the easiest way of updating Elelabs Zigbee/Thread Products to a newer version or to switch between Zigbee and Thread version. The firmware update files are stored in the same repository and are automatically selected by the utility itself.
Switch/update to latest Zigbee
python3 Elelabs_EzspFwUtility.py ele_update -p /dev/ttyS6 -v zigbee
Switch/update to latest Thread
python3 Elelabs_EzspFwUtility.py ele_update -p /dev/ttyS6 -v thread
for any EZSP/Spinel product
The probe
is used to detect the version of the connected Zigbee/Thread product or to detect if the product is in bootloader mode.
python3 Elelabs_EzspFwUtility.py probe -p /dev/ttyS6
Product in Zigbee EZSP mode
Product in Thread Spinel mode
Product in bootloader mode
for any EZSP/Spinel product
The restart
is used to probe the connected Zigbee/Thread product and restart it in normal or in bootloader mode. The normal mode is regular EZSP/Spinel operation. The bootloader mode is used only for the firmware update.
Switch from Normal mode to Bootloader mode
python3 Elelabs_EzspFwUtility.py restart -m btl -p /dev/ttyS6
Switch from Bootloader mode to Normal mode
python3 Elelabs_EzspFwUtility.py restart -m nrml -p /dev/ttyS6
for any EZSP product
The flash
is used to restart the connected EZSP product in bootloader mode and perform Firmware Update using XMODEM protocol. You need to provide an actual file for this utility. !!BE CAREFULL!! as this might damage or 'brick' your product.
python3 Elelabs_EzspFwUtility.py flash -f YOUR_NEW_EZSP_FIRMWARE_FILE.gbl -p /dev/ttyS6
If for some reason the update
or flash
utility failed and your product is no longer responding.
probe
the EZSP adapter as described. Most probably it is now in the Bootloader moderestart
the EZSP adapter in nrml
mode. If success -> your product is working nowflash
the EZSP adapter with the firmware file. If the product is in btl
mode it will probably workinfo at elelabs.com
For integration with OpenHAB please see our our OpenHAB user guide.
For integration with Home Assistant see our Home Assistant user guide. Please note if you are using the EZSP v8 firmware you will also have to add the following to your configuration.yaml
for the Home Assistant ZHA integration to load successfully.
zha:
zigpy_config:
ezsp_config:
CONFIG_APS_UNICAST_MESSAGE_COUNT: 12
CONFIG_SOURCE_ROUTE_TABLE_SIZE: 16
CONFIG_ADDRESS_TABLE_SIZE: 8