search

EliasKotlyar / Xiaomi-Dafang-Hacks

4.16k stars 1.01k forks source link

Can't install CFW on Dafang 2017DP3894 on 5.5.1.353 #669

Closed DanielePetrarolo closed 3 years ago

DanielePetrarolo commented 5 years ago

Hello everyone

I really can't install the CFW on my dafang DF3 1080p. I tryed eveything. Downlaod cfw from 1.0 to 1.3, put on microsd, holdsetup button than powered and release at different times. I tried 2 different microsd from Lexar: one is 16GB the other is 8GB. Eveytime I try to flash the camera start spin in just 20seconds, and when I test the blue shining led, I don't get it. Also, passing the steps above give me no result. The camera use always the original firmware. On MiHome the camera is on firmware 5.5.1.353.

Can you give me some advice?

Maybe my DaFang is a new versione? I have bought it some weeks ago.

audisport commented 5 years ago

well, first of all, you need to disassemble your camera (only 2 screws) Then, you'll have access to the main board as seen here

Then, you need to open a serial console (minicom on Linux, iTerm on MacOS, if you are on windows, I would suggest to reinstall a real OS :)). The settings should be 115200,8,N,1. Then you'll be able to watch the boot sequence as I have shown last week.

When you have the prompt Ingenic-uc1_1 login: type root and the password is ismart12

Then you should unpack the latest .bin firmware and copy the files on your SD card as shown here

When this part is done, plug your SD card back on the camera and use dd to write directly to the NAND every part of the firmware manually. dd if=uboot.bin of=/dev/mtdblock0 dd if=kernel.bin of=/dev/mtdblock1 dd if=rootfs.bin of=/dev/mtdblock2 dd if=driver.bin of=/dev/mtdblock3 dd if=appfs.bin of=/dev/mtdblock4 dd if=backupk.bin of=/dev/mtdblock5 dd if=backupd.bin of=/dev/mtdblock6 dd if=backupa.bin of=/dev/mtdblock7 dd if=config.bin of=/dev/mtdblock8 dd if=para.bin of=/dev/mtdblock9 dd if=flag.bin of=/dev/mtdblock10

Hope this will help some of you. In any case, if you don't understand what you are doing or if you are not sure, please : DON'T DO ANYTHING and wait for the next release, it probably will take care of the actual issue.

Cheers !

HI! I tried to came back original firmware. I did everything you wrote, but the terminal tells me that login/password(root/ismart12) are wrong. Camera Dafang, firmware now CFW. Standard metod with reset button don`t work, i tried all sd wich i had, and make 1 part 512mb. Help me... Have a nice day.

xorcor commented 5 years ago

WYZE Cam V2 was fully updated via Wyze App to 4.9.2.52 flashed back to 4.9.2.18-1 Flashed CFW. Currently running dafang hacks with no issue.

WYZE Original: https://discourse-cloud-file-uploads.s3.dualstack.us-west-2.amazonaws.com/wyze/original/2X/e/e889095c9b8718438f9c44fa5ea091dc8e20777e.zip

idcrook commented 5 years ago

I had recently got Wyze Cam V2. Came with 4.9.1.76. Installed into Wyze App and instructed it to not update FW when asked. Successfully installed CFW, which now reports 4.9.1.60 in Wyze App.

Just curious which of these it is possible to use with CFW, and/or update "original" FW image with Wyze Cam V2 Firmware lists following:

UPDATE 29-Dec-2018: Added 4.9.3.64

For now, I think I will not "upgrade" Wyze FW until this issue is resolved.

deten commented 5 years ago

I have the 4.9.1.76 firmware I couldnt get the bootloader to install.

s13678 commented 5 years ago

WYZE Cam V2 was fully updated via Wyze App to 4.9.2.52 flashed back to 4.9.2.18-1 Flashed CFW. Currently running dafang hacks with no issue.

WYZE Original: https://discourse-cloud-file-uploads.s3.dualstack.us-west-2.amazonaws.com/wyze/original/2X/e/e889095c9b8718438f9c44fa5ea091dc8e20777e.zip

@bryptik the link to WYZE original firmware comes up with an access denied issue. Could you re-host elsewhere please? (Or let me know where you got it originally - it's not hosted by WYZE anymore)

idcrook commented 5 years ago

WYZE Cam V2 was fully updated via Wyze App to 4.9.2.52 flashed back to 4.9.2.18-1 Flashed CFW.

@bryptik the link to WYZE original firmware comes up with an access denied issue. Could you re-host elsewhere please? (Or let me know where you got it originally - it's not hosted by WYZE anymore)

It appears that the Flashing your WyzeCam v2 firmware page was edited yesterday, taking down the older versions/links from Wyze, and only keeping the recent ones, on a new server/link scheme. You can see this for yourself by clicking on the "2 (pencil)" history link on the top post. Sorry, I don't have copies hosted available of the older versions.

EDIT: it appears old versions are still available from main site (non-CDN), e.g., 

wget https://www.wyzecam.com/wp-content/uploads/2018/07/demo_4.9.2.18-1.zip
s13678 commented 5 years ago

Nice, that worked perfectly. Thanks!

yasuoza commented 5 years ago

New firmware V4.9.3.64 for Wyze Cam v2 is released at December 13, 2018.

It says says

Added more guard check before firmware upgrade to make upgrade safer https://support.wyzecam.com/hc/en-us/articles/360010068231-Wyze-Cam-v2-Firmware

is this a cure for "broken" bootloader commented at https://github.com/EliasKotlyar/Xiaomi-Dafang-Hacks/issues/669#issuecomment-441327163?

toldenburger commented 5 years ago

Man I seriously hope the wonderfull devs come up with a solution to this firmware problem.

lkaino commented 5 years ago

Just bought a Dafang, came with a SW version 5.5.1.328. Doesn't seem to flash with CFW. Any additional tests I could run to help the investigations?

mjoach commented 5 years ago

I got Dafang with 5.5.1.328 firmware last week as well and was relieved to see it still works with CFW. Took a few tries though, so make sure it's not down to your SD card formatting.

sendorm commented 5 years ago

Latest version of dafang is 5.5.1.419. Did anyone have any luck with this firmware?

macsims commented 5 years ago

Links that currently still work for older WyzeCam firmwares:

https://www.wyzecam.com/wp-content/uploads/2018/07/demo_4.9.2.18-1.zip https://www.wyzecam.com/wp-content/uploads/2018/06/demo_4.9.1.76.zip https://www.wyzecam.com/wp-content/uploads/2018/04/demo_4.9.1.60.zip https://www.wyzecam.com/wp-content/uploads/2018/04/demo_4.9.1.42.zip

TSparkas commented 5 years ago

I have successfully used CFW on Dafang firmware 5.5.1.243 (arrived in December). Was struggling initially with SD card as it was not mounting the card with just 512 MB partition on 32GB card. Only worked when formatted full partition on 32GB card. Had to connect via serial console to see what was causing problems.

tylerl commented 5 years ago

For Wyze v2: I just set up a new camera per manufacturer instructions, did the automatic download/install of the latest firmware (4.9.3.64), and then after that used the standard sdcard method to flash the CFW and successfully booted the latest modded firmware.

No troubles at all. Since I was expecting trouble, I had already added serial pin headers, and I got serial transcript of the whole pre-flash (standard FW), during-flash, and post-flash (modded FW) boot processes if anyone needs any information out of them. Everything looks pretty unremarkable though; it all "just worked" as advertised.

idcrook commented 5 years ago

Wyze V2: 4.9.3.64

Thanks. I, too, can confirm that 4.9.3.64 on Wyze v2 is compatible with CFW:

  1. Upgraded to 4.9.3.64 using Wyze app on iOS
  2. Performed normal µSD CFW install (NOTE: iOS app will report 4.9.1.60 FW version afterward for OEM FW since that is the FW that comes with CFW bootloader)
robyevolution commented 5 years ago

Hello i have a Dafang 2017DP3894 fw 5.5.1.285 , this hack woks on this model??

cksonny commented 5 years ago

Guys, honestly, been having this problem for more than 2 weeks. I then took a brand new card and the formatted it to 400 mb. Then followed the demo.bin step followed by the remaining steps. Turns out the other 2 SD cards I had previously used had some invincible partitions that prevented me from installing. The best way to identify this is, try deleting all the partitions inside the SD card using Windows 'Disk Management', if you get an error, the SD card is the root of your problem.

danmed commented 5 years ago

@cksonny not sure if you are in the wrong thread or what, but this is due to the latest firmware preventing demo.bin from being loaded on boot.. nothing to do with SD cards.

cksonny commented 5 years ago

Why don't you try reading the thread from the beginning?

palakmar commented 5 years ago

can one downgrade firmware to get this working?

palakmar commented 5 years ago

Ok, this is my first time doing this so can you please explain?

  1. Do I need a bootloader?
  2. Once I flash to 5.5.1.194 do I do the flash?

Sorry I have all these questions but I am not sure what to do Marceli Palak

On Tue, Jan 15, 2019 at 3:14 PM NeroNeckbeard notifications@github.com wrote:

Yes, I had the latest firmware (5.5.1.419) and also couldn't install cfw-1.3.bin.

  1. Download "demo_5.5.1.194.bin" and copy it to the root of FAT32 formatted SD Card an rename it to "demo.bin"
  2. With power removed insert SD Card into camera.
  3. While holding down the "Setup" button, plug in the power cable.
  4. After about 5 seconds both the yellow and blue LEDs on the front will be illuminated. The firmware is now flashing, mine took about 50 seconds.
  5. Follow the normal hack installation.

— You are receiving this because you commented. Reply to this email directly, view it on GitHub https://github.com/EliasKotlyar/Xiaomi-Dafang-Hacks/issues/669#issuecomment-454553842, or mute the thread https://github.com/notifications/unsubscribe-auth/AsjZS90jdY_Rdva-gTQE3QeR-v5frtR4ks5vDkS_gaJpZM4WWWGd .

harald-mue commented 5 years ago

I own also a dafang with firmware 5.5.1.353 and was not able flashing. Can somebody confirm flashing the "demo_5.5.1.194.bin" does the trick?

Thx.

danmed commented 5 years ago

Anyone able to tell me where to get a firmware for the Xiaofang 1s that i can use to downgrade from the latest firmware? I can't decypher anything in this thread as it's a mixture of Xiaofang / Wyze and Dafang...

The firmware for Xiaofang in this github seems to be decompiled and i can't find any instructions on how to put it all back together as a demo.bin

hansaya commented 5 years ago

I have been messing with my Waze Pan for few hours and I managed to replace the uboot. Since there are lot of people here with various issues. I'm focused on fixing the original issue where you get uboot error to load the demo.bin

1) First what worked: I manged to use https://github.com/anmaped/openfang project and got rstp stream working. How? You can get into the uboot console at the beginning by spamming the console at the boot time and installed a custom uboot.

fatload mmc 0:1 0x80600000 u-boot-lzo-with-spl.bin
sf probe
sf update 0x80600000 0x000000000000 0x000000040000

Then you go through guide on the github to create memory card to load the operating system.

What bad with this system? Well I did not like the uboot build because it was half broken and I didnt like how hard it is to get going. (first world problems)

2) Then I managed to install newly built uboot from https://github.com/Dafang-Hacks/uboot/tree/master/compiled_bootloader

fatload mmc 0:1 0x80600000 dafang_128mb_v2.bin
sf probe
sf update 0x80600000 0x000000000000 0x000000040000

U-boot seems to work fine but it does not seems to be designed to run cfw image to create the bootable memory card so it starts up the default waze image.

3) This where i'm at now. Does anyone has the boot loader that works with this project? I cannot seems to find it. I managed to install https://github.com/EliasKotlyar/Xiaomi-Dafang-Hacks/tree/master/hacks/recovery and I have broken camera now :) (anything for science). Next plan is to take the spi chip out and program it manually.

grigio commented 5 years ago

I confirm that the flashing instructions worked on Xiaomi Xiaofang 1S fw stock 5.6.2.77, Thanks. Just the led feeback is different

feazzu commented 5 years ago

I own also a dafang with firmware 5.5.1.353 and was not able flashing. Can somebody confirm flashing the "demo_5.5.1.194.bin" does the trick?

Thx.

Yes, It Works!!!

harald-mue commented 5 years ago

I own also a dafang with firmware 5.5.1.353 and was not able flashing. Can somebody confirm flashing the "demo_5.5.1.194.bin" does the trick? Thx.

Yes, It Works!!!

I can now also confirm downgrading a dafang (firmware 5.5.1.419) works with "demo_5.5.1.94.bin". The third sd-card I've tried finally worked. After downgrading (can be verify with mi home app) you simply follow the instructions.

Don't give up and try various sd-cards. Older 4GB and 8GB cards both did't work - a 32GB (fully formatted) did the job finally.

sendorm commented 5 years ago

I can also confirm that downgrading to 194 first did the trick for me. I also used a 32GB sd card with no problems.

machineglow commented 5 years ago

I had recently got Wyze Cam V2. Came with 4.9.1.76. Installed into Wyze App and instructed it to not update FW when asked. Successfully installed CFW, which now reports 4.9.1.60 in Wyze App.

Just curious which of these it is possible to use with CFW, and/or update "original" FW image with Wyze Cam V2 Firmware lists following:

UPDATE 29-Dec-2018: Added 4.9.3.64

  • [x] 2018/12 4.9.3.64 - 29-Dec-2018: flashes CFW normally, according to below
  • [ ] 2018/10 4.9.2.52 - does not flash CFW, according to above
  • [ ] 2018/09 4.9.2.42
  • [x] 2018/07 4.9.2.18 - DOES flash CFW after downgrade to 4.9.2.18-1 from 4.9.2.52, according to above
  • [x] 2018/06 4.9.1.76 - came with my Cam V2, did flash CFW based on 4.9.1.60
  • [x] 2018/04 4.9.1.60 - assume DOES flash
  • [ ] 2018/04 4.9.1.42
  • [ ] 2018/04 4.9.1.34

For now, I think I will not "upgrade" Wyze FW until this issue is resolved.

Hey guys... Soooo.. just to confirm, the latest official FW from wyzecam is compatible with dafang hacks? I'm about to buy another wyzecam pan/V2 and want to make sure I can set it up with dafang.

I'm just confused that wyzecam would take away the functionality and then put it back in...

d00lar commented 5 years ago

i can also confirm downgrade dafang using demo_5.5.1.194.bin then normal bl flash and then copy files with no problems at all using some random 8gb microsd thanks !

bradley-madaris commented 5 years ago

I'm not sure what OS you guys are using to format your micro SD card but I was having a heck of a time with it on macOS Mojave 10.14.3. I sat around and thought about it... Maybe Disk Utility wasn't formatting it correctly. I opened up Terminal an used this to format my micro SD card...

sudo diskutil eraseDisk FAT32 UNTITLED MBRFormat disk3

For some reason, after formatting it with MBRFormat attached to the line, it made it work without a single issue. Of course, you would switch the location of your disk, disk3 to whichever location is provided when running diskutil list.

I should also mention that I am formatting the micro SD card for a Wyze Pan.

hellad commented 5 years ago

@d00lar From what version of firmware have you downgraded? I try to do this from 5.5.1.419 with no luck. I used 3 different microSD cards from 4 to 32Gb capacity.

I also should add to @bradleymadaris post that there was unobvious problem with microSD card formatting in my case. I used to use Easus partition manager to quickly change partition types and size. Only when I connected to serial port of my Dafang 1080P camera I saw error message when system attempted to access microSD card. Finaly I found out that there was free space about 7.5Mb BEFORE first FAT partition. Then I format microSD card with unother old program - SDformatter. And problem gone.

Now camera can see microSD card. Unfortunately my Dafang camera can not be downgraded using demo_5.5.1.194.bin yet.

Below I attached boot log while attempted to downgrade (long list, sorry). It's unclear for me what is the reason of failure. I don't see error messages about wrong size of firmware as discussed before in this thread. I'd appreciate any ideas what can I do next.

I suppose that the only way to hack my camera now is

Hope this sequence will not break the camera ;) .

Also I'd like to know how to eliminate negative impact of constant log output in serial console. It's really disturbing. Does somebody redirect it to file?

Bootlog when tried to downgrade from 4GB microSD card. Xiaomi Dafang Demo.bin flash attempt with well formatted 4G.log

ghost commented 5 years ago

Been trying to get both a Dafang and Xiaofang model to work, but unfortunately in my network setup, despite creating an isolated WiFi and VLAN just to test the linking between the Mi Home app and the cameras, they successfully associate and get a DHCP lease (and communicate with a gazillion China-based hosts via TCP/UDP connections to all kinds of ports, including some unusual Alibaba-owned networks) but the app gets stuck at "Connecting device to network", as if it could not see the cameras.

I'm not sure where to go from there, as there is zero documentation on how to locally upgrade or downgrade the firmware, or even files to download for that purpose.

danmed commented 5 years ago

Been trying to get both a Dafang and Xiaofang model to work, but unfortunately in my network setup, despite creating an isolated WiFi and VLAN just to test the linking between the Mi Home app and the cameras, they successfully associate and get a DHCP lease (and communicate with a gazillion China-based hosts via TCP/UDP connections to all kinds of ports, including some unusual Alibaba-owned networks) but the app gets stuck at "Connecting device to network", as if it could not see the cameras.

I'm not sure where to go from there, as there is zero documentation on how to locally upgrade or downgrade the firmware, or even files to download for that purpose.

I was in a similar situation (i believe you are wanting to downgrade a Xiaofang in order to apply the hacks?) and i finally figured it out...

XIAOFANG: Download demo.bin from https://www102.zippyshare.com/v/OhOnBJg6/file.html Format a SD card (I used an 8GB and formatted to Fat32) Paste the file into the SD card Eject then insert SD card into the camera Hold the reset/setup button (make sure the camera is unplugged first) Plug the camera Wait for about 15 seconds You should see the yellow light turn into blue then flashing like normal again.

You will now be on 5.6.2.45 which the hacks work on

d00lar commented 5 years ago

No idea - it was saying 4days ago that no updates found so guess last? (Without downgrade hack was not working ) I formated on win10 using 'defsults' fat32 default Block size etc.

hellad commented 5 years ago

Latest firmware of Dafang camera can be hacked.

I'd like to share my experience.

I successfully downgraded my Dafang 1080P camera from version 5.5.1.419 to demo_5.5.1.177.bin . The 4GB microSD card was used. That was the key factor in my case I beleive. Having beed downgraded, the camera's motor did not stop working during initial startup (until power off). New calibration was required.

After that I successfully hacked camera to cfw-1.3.bin. Unfortunately web GUI of my camera was unstable with significant delays. Some items in Settings menu did not react.

Later I successfully flashed version 5.5.1.194 for the test purposes and then again to cfw-1.3.bin.

Some problems still exist. Video at rtsp://dafang:8554/unicast not available while service started. But pictures are displayed in web gui and motion capture can be sent to telegram. So I don't see camera in my home-assistant. Vertical motion up does not work till I try to move down first. Motor calibration does not react in settings menu. Mqtt integartion with my mosquitto server works but in home-assistant log I see regular error messages like Jan 27 21:21:05 hassbian hass[717]: 2019-01-27 21:21:05 WARNING (MainThread) [homeassistant.components.cover.mqtt] Payload is not True or False: 0 Jan 27 21:21:05 hassbian hass[717]: 2019-01-27 21:21:05 WARNING (MainThread) [homeassistant.components.cover.mqtt] Payload is not True or False: 0

During boot I see many repeated error messages that should not exist in my opinion (see below).

I continiue my tests.

[ 47.942275] i2c i2c-0: i2c_jz_irq 441, I2C transfer error, ABORT interrupt [ 47.949414] i2c i2c-0: --I2C txabrt: [ 47.953141] i2c i2c-0: --I2C TXABRT[0]=I2C_TXABRT_ABRT_7B_ADDR_NOACK [ 47.959742] error: sensor_read,172 ret = -5 [ 47.964089] sensor_read: addr=0xa value = 0x0 [ 47.968693] err sensor read addr = 0xa, value = 0x0 [ 48.033902] i2c i2c-0: i2c_jz_irq 441, I2C transfer error, ABORT interrupt [ 48.041032] i2c i2c-0: --I2C txabrt: [ 48.044754] i2c i2c-0: --I2C TXABRT[0]=I2C_TXABRT_ABRT_7B_ADDR_NOACK [ 48.051352] error: sensor_read,172 ret = -5 [ 48.055697] sensor_read: addr=0x300a value = 0x0 [ 48.060571] err sensor read addr = 0x300a, value = 0x0 [ 48.126066] i2c i2c-0: i2c_jz_irq 441, I2C transfer error, ABORT interrupt [ 48.133516] i2c i2c-0: --I2C txabrt: [ 48.137231] i2c i2c-0: --I2C TXABRT[0]=I2C_TXABRT_ABRT_7B_ADDR_NOACK [ 48.143962] error: sensor_read,172 ret = -5 [ 48.148300] sensor_read: addr=0x300b value = 0x0 [ 48.153273] err sensor read addr = 0x300b, value = 0x0

miklos-szel commented 5 years ago

If anybody is interested: the hack worked on a newly ordered Dafang. It had stock 5.5.1.243 which was downgraded to 5.5.1.194, the cfw was installed successfully afterwards. SD Card: 16GB Sandisk formatted the whole disk with FAT32 under windows.

kenysc99 commented 5 years ago

I can confirm a newly bought Dafang from China Taobao with stock fw 5.5.1.328 able to flash the CFW. This was done with a 512MB SD card.

This camera labelled "For use in Mainland China only" costs US$24.

filippocobelli commented 5 years ago

Hi How to pack o other dafang firmware instead of the usual 5.5.1.177 or 5.5.1.194?

hellad commented 5 years ago

I believe that you need file https://github.com/EliasKotlyar/Xiaomi-Dafang-Hacks/blob/master/firmware_original/demo_5.5.1.177.bin from https://github.com/EliasKotlyar/Xiaomi-Dafang-Hacks/blob/master/hacks/technical.md page.

вс, 7 апр. 2019 г. в 12:16, Art Deineka notifications@github.com:

@hellad https://github.com/hellad

I successfully downgraded my Dafang 1080P camera from version 5.5.1.419 to demo_5.5.1.177.bin . The 4GB microSD card was used. That was the key factor in my case I beleive. Having beed downgraded, the camera's motor did not stop working during initial startup (until power off). New calibration was required.

which of these files https://github.com/EliasKotlyar/Xiaomi-Dafang-Hacks/tree/master/firmware_original/dafang/5.5.1.177 I need to rename to demo.bin to downgrade to version 177 ?

— You are receiving this because you were mentioned. Reply to this email directly, view it on GitHub https://github.com/EliasKotlyar/Xiaomi-Dafang-Hacks/issues/669#issuecomment-480573279, or mute the thread https://github.com/notifications/unsubscribe-auth/AcVz9O4aPQ8zYxLAY8MIEWC-aVFgnkSpks5vebeCgaJpZM4WWWGd .

time2kite commented 5 years ago

I confirm that I just unbricked my Xiaomi Dafang with the NEWEST FIRMWARE from April 2019. Thank you SO MUCH to those Github guys who spent spare time in providing this hack.

Foden7 commented 5 years ago

On a Wyze v2 I can only get the hack to run if i use v4.9.1.60, from the original Defang thread. If i upgrade past that either via the Wyze app or manually i cannot get the hack to work. I use 2 SD cards, one for the firmware upgrade and the other is the running SD with he Defang hack. So my config/setup is consistent - any idea what I am missing?

umairatstride commented 5 years ago

Can I use this on a Jennov 1080p? They don't post very good specifications on their site!

DdenBraver commented 5 years ago

I can confirm that the hack works perfectly on a new Dafang (ordered recently) with the latest firmware. Steps to install:

rudraksh90 commented 5 years ago

I can confirm that the hack works perfectly on a new Dafang (ordered recently) with the latest firmware. Steps to install:

  • Clean partitions and volumes on the micro sd-card. (diskpart --> select disk --> clean).
  • Create a new volume of 512MB, format it FAT32
  • Install firmware (downgrade) demo_5.5.1.177.bin
  • Install firmware cfw-1.3.bin

Can you share the link, from where you bought the camera? I have tried several times, but its not working for me..

DdenBraver commented 5 years ago

@rudraksh90 https://s.click.aliexpress.com/e/D6a0ncORp

rudraksh90 commented 5 years ago

@rudraksh90 https://s.click.aliexpress.com/e/D6a0ncORp

Thank you,

I will try to order it and flash the cfw..

rudraksh90 commented 5 years ago

I can confirm that the hack works perfectly on a new Dafang (ordered recently) with the latest firmware. Steps to install:

  • Clean partitions and volumes on the micro sd-card. (diskpart --> select disk --> clean).
  • Create a new volume of 512MB, format it FAT32
  • Install firmware (downgrade) demo_5.5.1.177.bin
  • Install firmware cfw-1.3.bin

What is the procedure to downgrade the firmware? Do you have to press the set up button while powering up the camera, till the blue light comes up?

rudraksh90 commented 5 years ago

Guys, iam looking for some help..

it looks like iam able to install the CFW, but i cannot connect to my SSID..

i found this file in the config section:

If this file exist as usb_eth_driver.conf the run.sh wont load any WIFI subsystem and instead try to load the usb ethernet subsystem.

Currently it only supports the asix.ko driver

IS this why i cant connect to my wifi?

Can anyone provide some help please..?