The ZMK documentation covers both basic and advanced functionality and has a table of OS compatibility for keycodes. Please note that the RGB Underglow, Backlight and Power Management sections are not relevant to the Advantage 360 Pro's custom ZMK fork. For more information see this note
There is a web based GUI available for editing the keymap. It is available at https://kinesiscorporation.github.io/Adv360-Pro-GUI. This repository is also compatible with certain other web based ZMK keymap editors however they may have keycodes or behaviours that are not implemented on the 360 Pro and could cause unusual behaviour or build failures. Furthermore changes made on other keymap editors may not be compatible if one goes back to using the Kinesis GUI.
Certain ZMK features (e.g. combos) require knowing the exact key positions in the matrix. They can be found in both image and text format here
sudo apt-get install make
inside the WSL2 instance./mnt/c/path-to-repo
).On macOS brew can be used to install the required components.
brew install docker colima
colima start
Note: On Apple Silicon (ARM based) systems you need to make sure to start colima with the correct architecture for the container being used.
colima start --arch x86_64
sudo apt-get install docker make
make
to build firmware for both halves or make left
to only build firmware for the left hand side.firmware
directory for the latest firmware build. The first part of the filename is the timestamp when the firmware was built.The built docker container and compiled firmware files can be deleted with make clean
. This might be necessary if you updated your fork from V2.0 to V3.0 and are encountering build failures.
Creating the docker container takes some time. Therefore make clean_firmware
can be used to only clean firmware without removing the docker container. Similarly make clean_image
can be used to remove the docker container without removing compiled firmware files.
Follow the programming instruction on page 8 of the Quick Start Guide to flash the firmware.
left.uf2
to the USB drive and it will disconnect.right.uf2
to the mounted drive.Note: There are also physical reset buttons on both keyboards which can be used to enter and exit the bootloader mode. Their location is described in section 2.7 on page 9 in the User Manual and use is described in section 5.9 on page 14.
Note: Some operating systems wont always treat the drive as ejected after the settings-reset file is flashed or may throw a spurious error, this doesn't mean that the flashing process has failed.
If you encounter a git conflict when updating your repository to V3.0 please follow the instructions on how to resolve it here.
Updating from V2.0 based firmwares to V3.0 based firmwares can be a rather complex process. There are reset files for every major firmware revision as well as documentation on the update process available here.
Starting on 11/15/2023 the Advantage 360 Pro will now automatically record the compilation date, branch and Git commit hash in a macro that can be accessed with Mod+V. This will type out the following string: YYYYMMDD-XXXX-YYYYYY, where XXXX is the first 4 characters of the Git branch and YYYYYY is the Git commit hash. In addition to this the builds compiled by GitHub actions are now timestamped and also record the commit hash in the filename.
By default this keyboard has NKRO enabled, however for compatibility reasons the higher ranges are not enabled. If you want to use F13-F24 or the INTL1-9 keys with NKRO enabled you can change CONFIG_ZMK_HID_KEYBOARD_EXTENDED_REPORT=n
to CONFIG_ZMK_HID_KEYBOARD_EXTENDED_REPORT=y
in adv360_left_defconfig
By default reporting the battery level over BLE is disabled as this can cause some computers to spontaneously wake up repeatedly. If you'd like to enable this functionality change CONFIG_BT_BAS=n
to CONFIG_BT_BAS=y
in adv360_left_defconfig.
The color of the CAPS/NUM/SCROLL LOCK indicator LEDs may be configured by specifying a hexadecimal RGB color code. For example, CONFIG_ZMK_RGB_UNDERGLOW_MOD_COLOR=0xFF0000
would give red indicator colors. In order to set the indicator color on both modules, ensure that both adv360_left_defconfig and adv360_right_defconfig have been updated.
A total of 32 layers are supported by ZMK, with the highest currently active layer displayed using the layer LEDs on each of the left and right modules. All possible colors are listed below; for the first 8 layers the same color is displayed on both modules. After that, only the right module color will cycle through until "rolling over", which will cause the left module color to change as well (and this then repeats). To avoid confusion, the black/off LED color is only used for layer 0.
Layer # | L/R | Layer # | L/R | Layer # | L/R | Layer # | L/R |
---|---|---|---|---|---|---|---|
0 | 8 | 16 | 24 | ||||
1 | 9 | 17 | 25 | ||||
2 | 10 | 18 | 26 | ||||
3 | 11 | 19 | 27 | ||||
4 | 12 | 20 | 28 | ||||
5 | 13 | 21 | 29 | ||||
6 | 14 | 22 | 30 | ||||
7 | 15 | 23 | 31 |
The changelog for both the config repo and the underlying ZMK fork that the config repo builds against can be found here.
The Advantage 360 Pro is always getting updates and refinements. If you are willing to beta test you can follow this guide from ZMK on how to change where your config repo points to. The west.yml
file that is mentioned is located in config/. This link can take you to the file. Typically you will only need to change the revision:
to match the beta branch. There is currently no beta branch available for testing.
Feedback on beta branches should be submitted as a GitHub issue on the base ZMK repository as opposed to this config repository.
In the event of a major update the beta branch may not be compatible with the current mainline version of the config repository. If this is the case it will be detailed here along with instructions on how to update.
By default this config repository references a customised version of ZMK with Advantage 360 Pro specific functionality and changes over base ZMK. The Kinesis fork is regularly updated to bring the latest updates and changes from base ZMK however will not always be completely up to date, some features such as new keycodes will not be immediately available on the 360 Pro after they are implemented in base ZMK.
Whilst the Advantage 360 Pro is compatible with base ZMK (The pull request to merge it can be seen here if you want to see how to implement it) some of the more advanced features (the indicator RGB leds) will not work, and Kinesis cannot provide customer service for usage of base ZMK. Likewise the ZMK community cannot provide support for either the Kinesis keymap editor, nor any usage of the Kinesis custom fork.
Further support resources can be found on Kinesis.com:
In the event of a hardware issue it may be necessary to open a support ticket directly with Kinesis as opposed to a GitHub issue in this repository.