Shargeek Storm² Liquid Powerbank Reverse Engineering

I own both a first-gen Storm2 directly from the first Kickstarter campaign and a second-gen Storm2.
This repo contains my WIP reverse engineering efforts concerning the first-gen.
I don't know the extent to how they differ yet, except that the second-gen uses a smaller "Master Controller" package (48 instead of 64 pins).

I will probably keep updating this thread, if you want to keep up-to-date.

Motivation

I have a few small gripes with the stock firmware I'd like to improve, if possible:

The button long press time is way too long, which makes the 1-button interface even more tedious to use
Pass-through mode gets disabled if the SoC falls under 50%
DC in/out is limited to 3A, but USB-C1 output is capable of 5A
- Both the DC jack (PJ-051AH) and the DC-DC converter are capable of 5A, I don't understand this limit at all

General Interesting Points

If your Storm2 ever acts up, it can probably be fixed by pressing the reset button on the BMS PCB (underneath the right cover, only 4 screws to remove).
The "USB Controller" is actually capable of the full 20V 5A PD, but it's buck-only, so it's limited to ~15V output (and probably a bit less when the battery gets more empty). But they limited it to 3A, maybe because of thermal reasons.

Teardown

Remove the 4 screws of the right cover and remove it
Use a spudger to pry out the button and display cover. You need to use sketchy amount of force.
Slide out the transparent case
Disconnect the BMS data cable (yellow wires)
Disconnect the BMS from the mainboard by pushing against it from the back side (besides the XT30 connector)
Remove the 4 mainboard screws
The mainboard is held in place with a thick thermal pad, but you should now be able to remove it from the case
There's also this great teardown + review by ChargerLAB

ICs

(Silkscreen) Name	Chip	Notes
Master Controller	Marking: `Naxim NXMCB6 AOC18220F 19181010C 2020 A` Actually: `STM32F103RBT6` (or clone)	- Does display & button handling, talks to BMS, "USB Controller" and "PD Controller"
USB Controller	`SW3517S`	- Handles USB-C2 and USB-A port - Complete stand-alone DC-DC buck solution - Connected to the MC via I²C
PD Controller	`CS32G020` (`CSA36FX30`)	- Handles USB-C1 and DC port - Another MCU, Cortex M0 - Could be programmed via USB-C1 CC pin, but no documentation seems to exist
DC Buck-Boost Controller	`SC8812A`	- Controlled by PD Controller
Flash	`BY25D80`	- 1MB - Probably only stores display graphics
Coulombmeter Controller (BMS)	`Atmel SAMD10U 906B`	- Connected to the MC via I²C

Pinouts

Debug Pads

There are a few big debug pads in a cluster on the underside. 3.3V is on the top (and marked in silkscreen).	MC SWD	MC Debug UART
3V3	3V3	3V3
PA14 (SWCLK)	PA9 (TX1)	GND
PA13 (SWDIO)	PA10 (RX1)	PA1 (SWDIO)
GND	GND	PA2 (SWCLK)
		RST

Master Controller

Periph/Pin	Pins	Connected to
USART1	TX/RX: PA9/PA10	Debug pads (see above)
USART2	TX/RX: PA2/PA3	PDCtrl PA8 (UART RX) (RX/TX connected together via 20kOhm)
I2C1	SCL/SDA: PB8/PB9	BMS
I2C2	SCL/SDA: PB10/PB11	USBCtrl
PA4		Prob. SPI Flash CS
PB12		Enters debug state when high?
PC8		Mayb. display backlight?
PC15		Button (active low)

Unsorted RevEng Notes

The UART protocol always starts with 4 preamble bytes (0x55AA8181 for debug UART and 0x55AA0181 for comms with PD controller)
0x0801F000 - FFF (4K) is some kind of programmable flash data page

LeoDJ / Storm2-RevEng

readme