Open Eric-git-999 opened 2 years ago
I was able to dual mine ETH / TON; but as mentioned previously my 3070 LHR would only reach ~36MH (TON was ~950MH). No issues dual mining in my config - just the low ETH hashrate. BTW - driver 512.59
I am having a similar issue on my 3060ti running eth-ton dual mine. I made sure to run the miner exe file in admin mode. It only runs at 43M/h. I have restated the miner several times I tired lowering the memory but still no good. I am going to try it on t-rex and NB to test out that Unlock.
What is your core clock and power limit? Usually this needs to be increased. Eg: my 3060TIs use 1400-1450 with PL180 to achieve 59 ETH / 900-1200 TON (doing worse with hynix v1 mem)
Used recommended driver 512.15 in Windows, same overclocks as tested with NBminer. I tested dual mining Eth / Ton, and reducing overclocks as recommended on hashrate.no. I also tested running the 3 x 3060ti's by themselves, then the 3 x 3070's by themselves, and got some variation but in the wrong direction, for both 3060ti's and 3070's the unlocker would stop between 35 and 39 MH/s across the board. The best unlock I could get to for the 3060ti was 57MH/s (tested on 3 different cards with hashrate.no overclocks for Hynix memory), the worst card stopped at about 55 MH/s, the 3070's (also tested on 3 different cards) stopped unlocking at ~38 MH/s. I wanted to use LolMiner again for dual mining Eth / Ton, it seems the unlocker stops too early and starts Ton mining before fully unlocking. The 3060ti's are Hynix memory and get 64MH/s + using NBMiner, the 3070's get around 62.1 MH/s on NBMiner.
Can anyone else verify dual mining Eth / Ton unlock issues? Heading back to NBMiner for now, but fingers crossed LolMiner gets the unlock more stable!
But NBMiner doesn't have dual mode... so it is complicated to compare that. Have you put try to lolMiner.exe as administrator?.
Could you share some screenshoots of the miner?
I am having a similar issue on my 3060ti running eth-ton dual mine. I made sure to run the miner exe file in admin mode. It only runs at 43M/h. I have restated the miner several times I tired lowering the memory but still no good. I am going to try it on t-rex and NB to test out that Unlock.
If only 43 is that you haven't put lolMiner.exe as Administrator.
I was able to dual mine ETH / TON; but as mentioned previously my 3070 LHR would only reach ~36MH (TON was ~950MH). No issues dual mining in my config - just the low ETH hashrate. BTW - driver 512.59
Actual driver until new release is 512.15 it says it clearly in the release section.
Used recommended driver 512.15 in Windows, same overclocks as tested with NBminer. I tested dual mining Eth / Ton, and reducing overclocks as recommended on hashrate.no. I also tested running the 3 x 3060ti's by themselves, then the 3 x 3070's by themselves, and got some variation but in the wrong direction, for both 3060ti's and 3070's the unlocker would stop between 35 and 39 MH/s across the board.
The best unlock I could get to for the 3060ti was 57MH/s (tested on 3 different cards with hashrate.no overclocks for Hynix memory), the worst card stopped at about 55 MH/s, the 3070's (also tested on 3 different cards) stopped unlocking at ~38 MH/s. I wanted to use LolMiner again for dual mining Eth / Ton, it seems the unlocker stops too early and starts Ton mining before fully unlocking. The 3060ti's are Hynix memory and get 64MH/s + using NBMiner, the 3070's get around 62.1 MH/s on NBMiner.
Can anyone else verify dual mining Eth / Ton unlock issues? Heading back to NBMiner for now, but fingers crossed LolMiner gets the unlock more stable!