search

MartyMacGyver / ESP32_Adafruit_ILI9341

Driver and sample code for ILI9341-based TFT displays designed for the ESP32 / ESP32-WROVER-KIT
47 stars 11 forks source link

readme

Demos for ILI9341-based TFT displays using the Espressif ESP32

See end of this file for credits and code provenance

This project uses a combination of Adafruit's Arduino ILI9341 driver and their Arduino display graphics library (with a few extra fonts added from DSEG and processed via http://oleddisplay.squix.ch/).

The original Arduino libraries above work for those using the Arduino-ESP32 project, with some pin modifications for your particular setup (e.g., the ESP-WROVER-KIT, which also controls the backlight on GPIO_5). The ILI9341 driver in particular is ESP32-aware now.

While there are no plans to convert the native SDK-based demos below to Arduino-ESP32 code, Arduino-specific demos are included here now.

Demo code (tested using the ESP-WROVER-KIT)

About the SDK-based sample code:

THIS SECTION AND ITS CODE ARE CURRENTLY DEFUNCT

The sample code consists of two parts:

The driver itself and needed dependencies are in /driver and /include/driver.

The driver is written in C++ which is not well supported by ESP8266 toolchain and sdk, so some dirty hack is needed to properly contstruct C++ objects. The code for this is in user/routines.cpp.

In spite of the fact that according to the datasheet max ILI9341's clock speed is 10MHz mine robustly works at up to 40MHz so I added SPI speed prescaler macro at the beginning of hspi.c. Defining it to 1 means HSPI will be clocked at 40MHz, 4 means 10 MHz.

What to demonstrate is controlled by macro UIDEMO defined at the beginning of user_main.cpp. If it's defined then the sample HVAC controller UI is shown, else, the rotating cube is rendered.

Wiring (see code for the ESP-WROVER-KIT default values)

The code uses hardware HSPI with hardware controlled CS, so the wiring shall be as follows: 

ILI9341 pin --> ESP32 GPIO pin of choice
MOSI        --> GPIO13
MISO        --> n/c
CLK         --> GPIO14
CS          --> GPIO15
DC          --> GPIO2
Reset       --> pull up to 3.3V
GND         --> ground

Credits

Basis 1: https://github.com/adafruit/Adafruit_ILI9341 This is a library for the Adafruit ILI9341 display products

This library works with the Adafruit 2.8" Touch Shield V2 (SPI)
  ----> http://www.adafruit.com/products/1651

Check out the links above for our tutorials and wiring diagrams.
These displays use SPI to communicate, 4 or 5 pins are required
to interface (RST is optional).

Adafruit invests time and resources providing this open source code,
please support Adafruit and open-source hardware by purchasing
products from Adafruit!

Written by Limor Fried/Ladyada for Adafruit Industries.
MIT license, all text above must be included in any redistribution

Basis 2: https://github.com/adafruit/Adafruit-GFX-Library This is the core graphics library for all our displays, providing a common set of graphics primitives (points, lines, circles, etc.). It needs to be paired with a hardware-specific library for each display device we carry (to handle the lower-level functions).

Adafruit invests time and resources providing this open source code,
please support Adafruit and open-source hardware by purchasing
products from Adafruit!

Written by Limor Fried/Ladyada for Adafruit Industries.
BSD license, check license.txt for more information.
All text above must be included in any redistribution.

Both as modified by Sermus for the ESP8266: https://github.com/Sermus/ESP8266_Adafruit_ILI9341

Further modifications by Rudi, et. al. for the ESP32: http://esp32.com/viewtopic.php?f=18&t=636#p2907

Extended with text rendering routines from: http://www.instructables.com/id/Arduino-TFT-display-and-font-library/?ALLSTEPS

Original hspi code: https://github.com/Perfer/esp8266_ili9341