Mr-MIBonk / M.I.B._More-Incredible-Bash

M.I.B. - More Incredible Bash - The Army knife for Harman MIB 2.x aka MHI2(Q) units

GNU General Public License v2.0

465 stars 53 forks source link

bash carplay firmware harman mib mib2 mibsolution mqb navigation patch toolbox vim

readme

M.I.B. - More Incredible Bash

GEM

All bastards who stolen and selling this should be fucked🖕

NOT FOR COMMERCIAL USE - IF YOU BOUGHT THIS YOU GOT RIPPED OFF!

M.I.B. is distributed under the GNU General Public License v2.0. See LICENSE for more information.

Check https://github.com/Mr-MIBonk/M.I.B._More-Incredible-Bash/wiki for even more details about M.I.B and your MHIG/MHI2/MHI2Q unit.

NOTE:

M.I.B. is running on Harman MHIG (MIB1 High) and MHI2/MHI2Q (MIB2 High) units only.
Minimum requirement to run M.I.B. in GEM is GEM version 4.1+.
Old GEM of most units with old FW versions will automatically be updated to GEM 4.12 during M.I.B installation.
Make sure, that you always run latest M.I.B version --> https://mib.mibsolution.one & https://github.com/Mr-MIBonk/M.I.B._More-Incredible-Bash
For additional Information check https://github.com/Mr-MIBonk/M.I.B._More-Incredible-Bash/wiki & https://mibwiki.one

CAUTION:

Ensure that a external power is connected to the car during any flash or programming process!
It is not recommended to flash with running engine!
Power failure during flashing/programming will brick your unit.
All you do and use at your own risk!

M.I.B Functions:

Prepare SD card:

Extract all files of the M.I.B. to the root folder of a clean FAT32 formatted SD card
Make sure that your SD card is not write protected.
Patched IFS-stage2 images have to be placed on the SD card in the folder /patches
Pre-patched (CP, FEC and EL) ifs-root-stage2 images can be found for all recent MHI2 FW versions here: https://mib.mibsolution.one
You only have to copy the folder(s) you need for your car(s) - e.g. /patches/MHI2_ER_SKGxx_Pxxxx_MUxxxx_PATCH
They are already prepared in the right way, so that the tool can use them right away

There is also a example video guide available now:

FEC Generator:

M.I.B is generating custom FecContainer.fec files based on existing FecContainer.fec and addfec.txt in patch folder.
addfec.txt can be edited with any ASCII editor (Notepad++). DO NOT change EOL. Only not yet existing FECs will be added to container during the process.
Do NOT change FECContainer.fec with WhatTheFec tool, it will break file signature. M.I.B method will keep original FECs intact.

ExceptionList BUG

If your unit was patched with M.I.B before April 2021 run "Add new Fecs to FecContainer.fec" script in M.I.B -> PATCH.
This will switch over to FecContainer.fec based patch and avoid EL BUG - unit will get stuck during boot.

M.I.B. in Green Engineering Menu - GEM:

After M.I.B SD card is prepared
Insert the SD card into slot SD1 of your unit.
Enter Engineering/Red Menu to start SW Update. Select UPDATE, select SD card, select "FREE for all - M.I.B. Launcher V1.2", START update.
Installation of M.I.B. on your Unit will start. The unit will restart three time until update process is finished.
GEM will be activated as part of the installation.
SVM error has to be cleared via M.I.B. function in GEM after installation
Enter GEM on your unit
Select ==>>m.i.b<<== in GEM and have FUN!

IMPORTANT! SD card must be presented in SD slot 1 (SD1) to enable M.I.B. in GEM. --> no SD no M.I.B.

GEM screen layout is designed for 9.2'' screens but should work OK on 8'' just some text lines may look cut

Update to new M.I.B. version:

No need to reinstall M.I.B if you want to use a new version.
Just create a fresh SD with latest M.I.B. version and insert into unit.

Old way, D-Link Method: Connect to MHI2 and start M.I.B.:

This method is still available in M.I.B, but no longer fully supported.
Basic functions are still available - Full functionallity is only given via GEM
D-Link - e.g. DUB-E100 HW rev. D1 - USB-Ethernet adapter is required to connect to your MHI2 unit.
Use Putty/Kitty to connect via UART or Telnet (MIB IP:172.16.250.248) and login into RCC (recommended: port:123) or MMX (port:23).
Login and password for your units SW train has to be known.
Check your SW-train, a pre-patched ifs-root-stage2 has to be present within the folder /patches
Insert the SD card into slot SD1 of your MHI2 unit and login to the RCC shell:

Mount SD card in slot SD1
mount -uw /net/mmx/fs/sda0/

Start M.I.B by typing
/net/mmx/fs/sda0/start
Default screen size of Putty/Kitty is often too small to display the M.I.B. menu in full.
Increase the window size manually.

CONTACT:

GITHUB: https://github.com/Mr-MIBonk/M.I.B._More-Incredible-Bash
Telegram Channel: https://t.me/joinchat/EHt4RRksHcMQk6Xi6tFaBw
Wiki: https://github.com/Mr-MIBonk/M.I.B._More-Incredible-Bash/wiki & https://mibwiki.one
Get in contact with us to get support and provide feedback about M.I.B.

Supporting Documents:

https://mibsolution.one

user and pass: guest