Poket-Jony Marlin-A4MaxPro-2.0.x issues

Poket-Jony / Marlin-A4MaxPro-2.0.x

🖨 Marlin 2.0.x optimized for the Anycubic 4Max Pro 3D printer

GNU General Public License v3.0

55 stars 18 forks source link

issues

Newest

Newest Most commented Recently updated Oldest Least commented Least recently updated

files in sd card not showed in the lcd display of the printer

#53 anonimus25 opened 2 years ago
0
[FR] Z_Offset Menu

#52 kennethgomez01 opened 2 years ago
0
Creality CR Touch Compatibility

#51 kennethgomez01 closed 2 years ago
0
BLTOUCH pin

#50 kennethgomez01 opened 2 years ago
20
BLtouch precompiled

#49 usmcsni opened 3 years ago
1
[FR] Anycubic 4Max Pro v2 support

#48 me21 opened 3 years ago
6
Manual Bed Mesh Leveling/ Not work

#47 sambroprzem opened 3 years ago
3
[ISSUE] Trying to exchange pins D45 and D7 on Trigorilla

#46 javilonso closed 3 years ago
1
Bltouch

#45 Erik262 closed 3 years ago
0
[BUG] Compilation error with defined CASE_LIGHT_NO_BRIGHTNESS

#44 ABATAPA opened 3 years ago
1
[BUG] (Printer show message Printing Done after M1001 command)

#43 UnoPromilo opened 3 years ago
0
Auto shut-off doesn't work

#42 Qbalion opened 4 years ago
0
[BUG] Constant reboot

#41 MatLeb opened 4 years ago
11
[BUG] just updated to v2.1.9-rc (Marlin 2.0.x) and printer shuts down as turned on

#40 scalda closed 4 years ago
2
"Printing done" popup behaviour

#39 rkolosovskyi opened 4 years ago
0
[BUG] Mesh bed levelling: Z up | Z down commands are swapped.

#38 rkolosovskyi opened 4 years ago
2
Limit switch does not work

#37 WoodenLoony opened 4 years ago
1
[FR] Auto Shut Off enables after reboot

#36 reclaimer5146 opened 4 years ago
0
[BUG] Auto shutoff always enabled even when you disable

#35 reclaimer5146 closed 4 years ago
2
[BUG] LCD Print-Time output

#34 bernhardberger closed 4 years ago
1
Change temperature menu display

#33 Piazzi68 closed 4 years ago
1
config for BLTouch v3.1

#32 Erik262 closed 4 years ago
1
[BUG] screws hits z-axis thread

#31 Erik262 closed 4 years ago
2
[QUESTION] Autotuning Hotend / Hotbed in special menu not working

#30 achrainer closed 4 years ago
5
[BUG] axis movement speed not working correctly

#29 Poket-Jony closed 4 years ago
1
[BUG] heat up takes a long time

#28 Poket-Jony closed 4 years ago
1
[BUG] Implement missing Screen Start/Pause/Stop methods

#27 Poket-Jony closed 4 years ago
1
[FR] Generic RX/TX Display Class

#26 Poket-Jony opened 4 years ago
0
[BUG] AXIS_STEPS and Hotbed are wrong

#25 Poket-Jony closed 4 years ago
1
[BUG] Display Filelist does not work correctly

#24 Poket-Jony closed 4 years ago
3
use correct calculated junction_deviation value based on the stock acc

#23 bernhardberger closed 4 years ago
0
Dev

#22 bernhardberger closed 4 years ago
0
[BUG] MeshBed Leveling Broken (Y-Axis)

#21 bernhardberger closed 4 years ago
1
[FR] Enable Linear Advance, but set it to 0

#20 bernhardberger closed 4 years ago
3
[BUGFIX] Use Type5 for bed temp sensor

#19 bernhardberger closed 4 years ago
0
[BUG] Wrong Heatbed Thermistor

#18 bernhardberger closed 4 years ago
4
[FR] Adjust Filament Load/Unload lengths

#17 bernhardberger closed 4 years ago
2
Make use of CASE_LIGHT

#16 m-kozlowski closed 4 years ago
1
Filament Sensor not working (after starting a print)

#15 bernhardberger closed 4 years ago
1
[BUG] Print Resume doesn't work

#14 bernhardberger closed 4 years ago
1
[BUG] Hotend Fan always 100%

#13 bernhardberger closed 4 years ago
2
Readme

#12 rkolosovskyi closed 4 years ago
0
[FR] Rewrite whole display class

#11 Poket-Jony closed 4 years ago
6
[BUG] Wrong termistor type in default configuration file.

#10 rkolosovskyi closed 4 years ago
1
[SOLUTION] Light flickers when printing

#9 Erik262 closed 4 years ago
1
Update README.md

#8 alfrankgit closed 4 years ago
0
[BUG] (hotbed target temperature is always 0 at the screen)

#7 Nestor75 closed 4 years ago
1
[BUG] filament runout not send to serial host

#6 Nestor75 closed 4 years ago
9
[BUG] hotend PID configuration impossible with the suggested sensor

#5 Nestor75 closed 4 years ago
10
[BUG] Lack of Filament can not be removed

#4 Erik262 closed 4 years ago
3