issues
search
Poket-Jony
/
Marlin-A4MaxPro-2.0.x
🖨 Marlin 2.0.x optimized for the Anycubic 4Max Pro 3D printer
GNU General Public License v3.0
54
stars
18
forks
source link
issues
Newest
Newest
Most commented
Recently updated
Oldest
Least commented
Least recently updated
files in sd card not showed in the lcd display of the printer
#53
anonimus25
opened
2 years ago
0
[FR] Z_Offset Menu
#52
kennethgomez01
opened
2 years ago
0
Creality CR Touch Compatibility
#51
kennethgomez01
closed
2 years ago
0
BLTOUCH pin
#50
kennethgomez01
opened
2 years ago
20
BLtouch precompiled
#49
usmcsni
opened
3 years ago
1
[FR] Anycubic 4Max Pro v2 support
#48
me21
opened
3 years ago
6
Manual Bed Mesh Leveling/ Not work
#47
sambroprzem
opened
3 years ago
3
[ISSUE] Trying to exchange pins D45 and D7 on Trigorilla
#46
javilonso
closed
3 years ago
1
Bltouch
#45
Erik262
closed
3 years ago
0
[BUG] Compilation error with defined CASE_LIGHT_NO_BRIGHTNESS
#44
ABATAPA
opened
4 years ago
1
[BUG] (Printer show message Printing Done after M1001 command)
#43
UnoPromilo
opened
4 years ago
0
Auto shut-off doesn't work
#42
Qbalion
opened
4 years ago
0
[BUG] Constant reboot
#41
MatLeb
opened
4 years ago
11
[BUG] just updated to v2.1.9-rc (Marlin 2.0.x) and printer shuts down as turned on
#40
scalda
closed
4 years ago
2
"Printing done" popup behaviour
#39
rkolosovskyi
opened
4 years ago
0
[BUG] Mesh bed levelling: Z up | Z down commands are swapped.
#38
rkolosovskyi
opened
4 years ago
2
Limit switch does not work
#37
WoodenLoony
opened
4 years ago
1
[FR] Auto Shut Off enables after reboot
#36
reclaimer5146
opened
4 years ago
0
[BUG] Auto shutoff always enabled even when you disable
#35
reclaimer5146
closed
4 years ago
2
[BUG] LCD Print-Time output
#34
bernhardberger
closed
4 years ago
1
Change temperature menu display
#33
Piazzi68
closed
4 years ago
1
config for BLTouch v3.1
#32
Erik262
closed
4 years ago
1
[BUG] screws hits z-axis thread
#31
Erik262
closed
4 years ago
2
[QUESTION] Autotuning Hotend / Hotbed in special menu not working
#30
achrainer
closed
4 years ago
5
[BUG] axis movement speed not working correctly
#29
Poket-Jony
closed
4 years ago
1
[BUG] heat up takes a long time
#28
Poket-Jony
closed
4 years ago
1
[BUG] Implement missing Screen Start/Pause/Stop methods
#27
Poket-Jony
closed
4 years ago
1
[FR] Generic RX/TX Display Class
#26
Poket-Jony
opened
4 years ago
0
[BUG] AXIS_STEPS and Hotbed are wrong
#25
Poket-Jony
closed
4 years ago
1
[BUG] Display Filelist does not work correctly
#24
Poket-Jony
closed
4 years ago
3
use correct calculated junction_deviation value based on the stock acc
#23
bernhardberger
closed
4 years ago
0
Dev
#22
bernhardberger
closed
4 years ago
0
[BUG] MeshBed Leveling Broken (Y-Axis)
#21
bernhardberger
closed
4 years ago
1
[FR] Enable Linear Advance, but set it to 0
#20
bernhardberger
closed
4 years ago
3
[BUGFIX] Use Type5 for bed temp sensor
#19
bernhardberger
closed
4 years ago
0
[BUG] Wrong Heatbed Thermistor
#18
bernhardberger
closed
4 years ago
4
[FR] Adjust Filament Load/Unload lengths
#17
bernhardberger
closed
4 years ago
2
Make use of CASE_LIGHT
#16
m-kozlowski
closed
4 years ago
1
Filament Sensor not working (after starting a print)
#15
bernhardberger
closed
4 years ago
1
[BUG] Print Resume doesn't work
#14
bernhardberger
closed
4 years ago
1
[BUG] Hotend Fan always 100%
#13
bernhardberger
closed
4 years ago
2
Readme
#12
rkolosovskyi
closed
4 years ago
0
[FR] Rewrite whole display class
#11
Poket-Jony
closed
4 years ago
6
[BUG] Wrong termistor type in default configuration file.
#10
rkolosovskyi
closed
4 years ago
1
[SOLUTION] Light flickers when printing
#9
Erik262
closed
4 years ago
1
Update README.md
#8
alfrankgit
closed
4 years ago
0
[BUG] (hotbed target temperature is always 0 at the screen)
#7
Nestor75
closed
4 years ago
1
[BUG] filament runout not send to serial host
#6
Nestor75
closed
4 years ago
9
[BUG] hotend PID configuration impossible with the suggested sensor
#5
Nestor75
closed
4 years ago
10
[BUG] Lack of Filament can not be removed
#4
Erik262
closed
4 years ago
3
Next