Gigabyte-Z590i-Vision-D-11900k

Within this repository I share my Hackintosh EFI for my newest build based on Intels Rocketlake 11th Gen CPU.

Z590i and 11900k running macOS Ventura

Hardware used in this build:

CPU: Intel i9-11900k
Board: Gigabyte Z590i Vision D:
- Audio: Realtek ALC4080
- 1x 2.5GBase-T (Intel I225-V)
- 1x USB-C
- 2x Thunderbolt 4 ports (Intel JHL8540 Maple Ridge)
- 2x m.2 Slots
RAM: 32GB G.Skill Trident Z 3600Mhz CL18
AMD 6900XTXH (MSI Radeon RX 6900 XT Gaming Z)
Wifi/BT: Intel AX201, replaced by a Broadcom BCM94360NG for macOS Compatibilty. Works out of the box. The BCM94360NG fits into the original WiFi-card housing and sits under the IO-shield. Original antennas fit.
SSDs: 1x 2TB Samsung 980 Pro OEM (PM9A1) for Windows 10 (sits in the m.2 below the CPU) 1x 1TB Samsung 960 EVO for macOS (sits on the back of the board)
Case: NCASE M1 v6.1

What is working:

SMBIOS MacPro7,1 with full h264/h265 hardware encoding
Audio: working out of the box as it is connected like a USB-Audio interface. But keep in mind it only shows up, when you plugin something (e.g. headphones).
Thunderbolt 4 (incl. Hotplug, tested with Monterey 12.5 and Ventura Beta 5)
Replacing the internal m.2 Intel Wifi with a BCM94360NG to have macOS native Wifi/BT Support
USB-ports. Have created my custom USB port mapping with USBMap.command

What is not working:

iGPU, the 11th Gen iGPU is not supported by macOS

Wifi in macOS Sonoma

With macOS Sonoma, the Broadcom based Wifi cards don't work plug and play anymore. It is a very annoying process now, that you have to repeat after every macOS Update!

General Requirements for Broadcom Wifi in Sonoma:

Additional Kexts: IO80211FamilyLegacy.kext, IOSkywalkFamily.kext, AMFIPass.kext. Also these Kexts in a very high priority after Lilu and VirtualSMC.
Blocking Kexts: com.apple.iokit.IOSkywalkFamily
Bootarg: -amfipassbeta
NVRAM: csr-active-config=<03080000>

To be repeated for every macOS Update:

Disable SecureBoot via config.plist: SecureBootModel = Disabled and DmgLoading = Any
Disable SecureBoot in BIOS
Install the macOS Update
Run the OCLP Patcher and start the "Post-install Root Patch".
Enable SecureBoot via config.plist: SecureBootModel =(your SecureBootModel according to here: https://dortania.github.io/OpenCore-Post-Install/universal/security/applesecureboot.html#securebootmodel) and DmgLoading = Any
Enable SecureBoot in BIOS again

Getting the OpenCore Legacy Patcher

Install the newest release from here: https://github.com/dortania/OpenCore-Legacy-Patcher/releases

USB Port Mapping

Update (05.01.23): Z590 Vision D Users I have added a USB port configuration for the ATX version Z590 Vision D as well. You just have to disable SSDT-USB-Ports-Z590i-VisionD.aml and enable SSDT-USB-Ports-Z590-VisionD.aml.

USB Port Mapping Z590i Vision D

BIOS-settings:

Current BIOS version: F8b
Load optimized defaults
Set Above 4G Decoding to Enabled
Set Legacy USB Support to Disabled
Set Intel VT-D to Enabled (DisableIOMapper is disabled, AppleVTD should be working)
Set Internal Graphics to Disabled (or Auto if you want to use it in Windows)
Thunderbolt:
- Discrete Thunderbolt Support: Enabled
- Wake From Thunderbolt Devices: Disabled
- Native OS security for TBT: Disabled
- Discrete Thunderbolt Configuration:
- Thunderbolt USB Support: Disabled
- Thunderbolt Boot Support: Disabled
- Titan Ridge Workaround for OSUP: Disabled
- Tbt Dynamic AC/DC L1: Disabled
- GPIO3 Force Pwr: Enabled
- Wait time in ms after applying Force Pwr: 200
- GPIO filter: Enabled
- DTBT Controller 0 Configuration: all Settings in this Submenu BIOS-Default
For Secure Boot:
- Set Secure Boot to Enabled
- Set Secure Boot Mode to Custom
- Go to Key Management and then Enroll EFI.
- Add all *.efi Files in your EFI Folder: BOOTX64.efi, all drivers(OpenRunTime.efi, OpenHFSPlus.efi, OpenCanopy.efi), OpenCore.EFI