IMPORTANT: This codebase is no longer actively maintained. The package will continue working, but support and changes are no longer provided. I will continue to make security updates so long as I have a device to use.
deckxstream
is a controller application for the Elgato Stream Deck. The application was created to allow Linux usage of a Stream Deck. The application relies heavily on the elgato-stream-deck NPM library. You will need to install udev rules and dependencies for this to install. See below
libxdo
bindings), application running (via child_process.spawn
)Udev on Linux will not allow access to the Stream Deck initially. Create /etc/udev/rules.d/50-elgato.rules
with the contents below and reload with sudo udevadm control --reload-rules
. NOTE: This setup assumes you are a member of the input
group. Use groups
on the command-line to see which groups you belong to substitute accordingly with plugdev
or similar. See elgato-stream-deck for more information.
SUBSYSTEM=="usb", ATTRS{idVendor}=="0fd9", ATTRS{idProduct}=="0060", MODE:="660", GROUP="input"
SUBSYSTEM=="usb", ATTRS{idVendor}=="0fd9", ATTRS{idProduct}=="0063", MODE:="660", GROUP="input"
SUBSYSTEM=="usb", ATTRS{idVendor}=="0fd9", ATTRS{idProduct}=="006c", MODE:="660", GROUP="input"
SUBSYSTEM=="usb", ATTRS{idVendor}=="0fd9", ATTRS{idProduct}=="006d", MODE:="660", GROUP="input"
KERNEL=="hidraw*", ATTRS{idVendor}=="0fd9", ATTRS{idProduct}=="0060", MODE:="660", GROUP="input"
KERNEL=="hidraw*", ATTRS{idVendor}=="0fd9", ATTRS{idProduct}=="0063", MODE:="660", GROUP="input"
KERNEL=="hidraw*", ATTRS{idVendor}=="0fd9", ATTRS{idProduct}=="006c", MODE:="660", GROUP="input"
KERNEL=="hidraw*", ATTRS{idVendor}=="0fd9", ATTRS{idProduct}=="006d", MODE:="660", GROUP="input"
NOTE: You may need to use SUBSYSTEMS
or KERNEL
instead of SUBSYSTEM
depending on your kernel. If you see permission errors trying to open a device, use udevadm info -a /dev/<device>
to see what you should be using.
xdo.h
is also a dependency. You can get this file via pacman -S xdotool
on Arch or apt-get install libxdo-dev
on Ubuntu/Debian
$ npm install -g deckxstream
$ deckxstream
Usage: deckxstream [options]
Options:
-V, --version output the version number
-c, --config <file> Configuration file to use. (default: "$HOME/.deckxstream.json")
-l, --list Show all detected Stream Decks and exit
-i, --init [device] Output an initial JSON file for the specified device if supplied
-k, --keys [device] Outputs the keyIndex values to each button on the specified Stream Deck (or first found) and exits
-h, --help display help for command
deckxstream
requires a configuration file. By default, it will attempt to load .deckxstream.json
in the HOME directory.
Example
{ "deckxstream-version": 1, "brightness": 70, "device": "somename", "screensaver": { "animation": "tumbler.gif", "brightness": 10, "timeoutMinutes": 20 }, "sticky": [ { "keyIndex": 0, "icon": "/some/dir/home.png", "changePage": "default", "text": "Home", "textSettings": { "fillStyle": "blue" } }, { "keyIndex": 4, "icon": "/some/dir/speaker.svg", "text": "Mute", "command": "amixer set Master toggle" } ], "pages": [ { "pageName": "default", "buttons": [ { "keyIndex": 1, "icon": "/some/dir/retroarch.svg", "changePage": "retroarch" }, { "keyIndex": 3, "dynamic": { "command": "resources/randomButton.js -r", "persistent": true } }, { "keyIndex": 5, "icon": "/some/dir/staticicondyntext.png", "dynamic": { "command": "resources/randomButton.js", "interval": 2000 } }, { "keyIndex": 6, "icon": "data:image/png;base64,iVBORw0KGgoAAAANSUhEUgAAAAEAAAABCAYAAAAfFcSJAAAADUlEQVQYV2NQu1DzHwAFBAJyENnpTwAAAABJRU5ErkJggg==" } { "keyIndex": 10, "icon": "/some/dir/lockscreen.svg", "sendkey": "super+l" }, { "keyIndex": 13, "icon": "redshift.svg", "changeBrightness": 10, "command": "redshift -x; redshift -O 4000 -b .5" }, { "keyIndex": 14, "icon": "brightness.svg", "changeBrightness": 70, "command": "redshift -x" } ] }, { "pageName": "retroarch", "buttons": [ { "keyIndex": 1, "icon": "/some/dir/retroarch.svg", }, { "keyIndex": 10, "icon": "save.svg", "sendkey": "F2", "text": "Save" }, { "keyIndex": 7, "icon": "plus.svg", "sendkey": "F7" }, { "keyIndex": 12, "icon": "minus.svg", "sendkey": "F6" }, { "keyIndex": 14, "icon": "load.svg", "sendkey": "F4", "text": "Load" } ] }, { "pageName": "dyn", "dynamicPage": "resources/randomPage.js -k 15" } ] }
A button can cause multiple actions to occur based on the configuration. The order of them is as follows on a single press:
changeBrightness -> sendkey -> sendtext -> command -> changePage -> startScreensaver
deckxstream-version
- Version number for the JSON file schema. Currently only 1
.
brightness
- Brightness to set to at start of application. Supports 0-100
. (Default: 90
)
device
- The device serial number to use if multiple Stream Decks are in use. (Default: first found)
screensaver
- Configuration block for the screensaver (Optional)
Value | Required | Notes |
---|---|---|
animation | Yes | Filename of the GIF to use as a screensaver |
brightness | No | Brightness to change the deck to when screensaver turns on |
timeoutMinutes | Yes | Time in minutes until screensaver kicks in |
sticky
- Sticky buttons. These buttons are available on EVERY page. If another page tries to load a button in the same location, it will be ignored. Entries follow the button format in an array. (Optional)
pages
- Pages for deck. On startup, a default
page will be loaded. (Optional)
Value | Required | Notes |
---|---|---|
pageName | Yes | The name for the page. default is loaded on startup. Use changePage to go to a different page. |
dynamicPage | No (Yes if no buttons) | Command to run to generate the page of buttons. Will be run by child_process.spawn when page is switched to. The called application should return {"buttons":[]} with the array filled with buttons. NOTE: Response must be JSON. |
buttons | No (Yes if not dynamic) | Array of buttons to load on the page. |
Value | Required | Notes |
---|---|---|
keyIndex | Yes | The key to bind to. For example, the standard Stream Deck would have 0-14. Run deckxstream -k to see the numbering for yours. |
icon | No | Either the filename or a Base64 data URI for an image to display in the button. The image will be automatically resized (respecting aspect ratio) to fit. |
text | No | A text label to place at the bottom of the button. If an icon is specified, it will be resized to allow the text to fit. |
textSettings | No | Changes the look of the label text. Use an object with properties for CanvasRenderingContext2D like fillStyle and font . |
changePage | No | On click, change the deck to the named page from the array of pages. |
changeBrightness | No | On click, change the brightness of the deck. Values of 0-100 supported. |
command | No | On click, run the given command using child_process.spawn |
sendkey | No | On click, send the given hotkey. Follows the naming of keys xdotool. |
sendtext | No | On click, send the given string to active window. |
startScreensaver | No | On click, start the screensaver. Value should be true . (Added in 1.0.0) |
dynamic | No | Dynamically sets up the button. Runs a given command to populate any of the other fields in this structure. See the dynamic structure below. NOTE: You CANNOT override keyIndex or dynamic with the results of the command. |
Value | Required | Notes |
---|---|---|
command | Yes | The command to run via child_process.spawn and listen on standard output. The output must be properly formed JSON. The JSON will overwrite any of the button configuration values until the next output. See below for an example. |
persistent | No | If true, the interval is ignored. Instead, the command is expected to be persistent and continously output JSON whenever a change is wanted. (false by default) |
interval | No (Yes if not persistent) | Time in ms between running the dynamic command. Keep in mind that if the text or icon of the button is changed, this can have an impact on system resources if the timeout is very short. |
dynamic
overwriteAs an example of dynamic
, let's say you have a checkEmail.sh
script which opens your mail client and hasEmail.sh
which checks to see if you have any new mail.
Given a button config of
{
"keyIndex": 0,
"icon": "/dir/mail.png",
"command": "checkEmail.sh",
"dynamic": {
"command": "hasEmail.sh",
"interval": 60000
}
}
If hasEmail.sh
returns
{
"icon": "/dir/mailanimated.gif",
"text": "6 New!"
}
The button will now be
{
"keyIndex": 0,
"icon": "/dir/mailanimated.gif",
"text": "6 New!",
"command": "checkEmail.sh",
"dynamic": {
"command": "hasEmail.sh",
"interval": 60000
}
}
If it then returns
{
"text": "0 New"
}
Then the button becomes
{
"keyIndex": 0,
"icon": "/dir/mail.png",
"text": "0 New",
"command": "checkEmail.sh",
"dynamic": {
"command": "hasEmail.sh",
"interval": 60000
}
}
The original configuration is used as the base between runs, not the the results of the previous run.