search

Spark-Concepts / xPRO

CNC xPRO Driver (4x DRV8825 motor drivers; dual motor confiurations on X,Y, or Z axis + wireless support
https://github.com/Spark-Concepts/xPRO
34 stars 27 forks source link

Check door error msg when setting up controller. #22

Open ambienthardwood opened 2 years ago

ambienthardwood commented 2 years ago

I recently purchased a queen bee pro with the xpro v5 controller. I have installed the latest firmware, cncjs software and I'm at the point where I would configure my axis'.

I've opened The serial port and I am getting a check door message.

Reffering back to the manual. I see that there is jumpers in the controller. I have move them in order of the diagram. But still I get the check door msg. What an I missing here?

Filippide77 commented 1 year ago

Please some news? I have the same problem. Windows 10 driver silabser.sys ver 11.3.0.176 CNCjs 1.10.3 COM4 Baud rate 115200 on CNCjs and system settings

message from controller ets Jun 8 2016 00:22:57 rst:0x1 (POWERON_RESET),boot:0x13 (SPI_FAST_FLASH_BOOT) configsip: 0, SPIWP:0xee clk_drv:0x00,q_drv:0x00,d_drv:0x00,cs0_drv:0x00,hd_drv:0x00,wp_drv:0x00 mode:DIO, clock div:1 load:0x3fff0018,len:4 load:0x3fff001c,len:1216 ho 0 tail 12 room 4 load:0x40078000,len:9720 ho 0 tail 12 room 4 load:0x40080400,len:6352 entry 0x400806b8 [MSG:Grbl_ESP32 Ver 1.3a Date 20201022] [MSG:Compiled with ESP32 SDK:v3.2.3-14-gd3e562907] [MSG:Using machine:CNC_xPRO_V5_XYYZ] [MSG:Axis count 3] [MSG:RMT Steps] [MSG:Init Motors] [MSG:TMCStepper Library Ver. 0x000701] [MSG:X Axis Trinamic TMC5160 Step:GPIO(12) Dir:GPIO(14) CS:GPIO(17) Disable:None Index:1 Limits(0.000,300.000)] [MSG:X Axis Trinamic driver test passed] [MSG:Y Axis Trinamic TMC5160 Step:GPIO(27) Dir:GPIO(26) CS:GPIO(17) Disable:None Index:2 Limits(0.000,300.000)] [MSG:Y Axis Trinamic driver test passed] [MSG:Y2 Axis Trinamic TMC5160 Step:GPIO(33) Dir:GPIO(32) CS:GPIO(17) Disable:None Index:3 Limits(0.000,300.000)] [MSG:Y2 Axis Trinamic driver test passed] [MSG:Z Axis Trinamic TMC5160 Step:GPIO(15) Dir:GPIO(2) CS:GPIO(17) Disable:None Index:4 Limits(-300.000,0.000)] [MSG:Z Axis Trinamic driver test passed] [MSG:PWM spindle Output:GPIO(25), Enbl:GPIO(4), Dir:None, Freq:5000Hz, Res:13bits] [MSG:Local access point CNC_xPRO_V5 started, 192.168.0.1] [MSG:Captive Portal Started] [MSG:HTTP Started] [MSG:TELNET Started 23] [MSG:Flood coolant on pin GPIO(21)] [MSG:Mist coolant on pin GPIO(21)] [MSG:X Axis limit switch on pin GPIO(35)] [MSG:Y Axis limit switch on pin GPIO(34)] [MSG:Z Axis limit switch on pin GPIO(39)] [MSG:Probe on pin GPIO(22)] Grbl 1.3a ['$' for help] [MSG:Check door]