This is a quick guide on how to use a Raspberry Pi to play modern turntables with USB output wirelessly on a Sonos installation. This guide is focussed on this usecase, but might also be used to stream to other speakers as we are going to create an MP3 stream which is playable by virtually anything that can stream audio.
First we need a clean installation of Raspbian on an SD card. As we do not need graphics or anything special, we can use Raspbian Lite. Also, we do not need much disk space, probably anything from 2GB and up is good. After installation I'm using only 1.5GB of my SD card.
For my installation, I have used the Buster
release of Raspbian OS Lite (September 2022). You might try out a newer version, but this is not tested.
Install Raspberry Pi OS Lite (64-bit) via the Raspberry Pi Imager https://www.raspberrypi.com/software/
Click the Gear icon for advanced options
vinyl
,Plug in your Raspberry Pi, ssh to it, and run the following
smorton@homepc:~$ ssh vinyl@vinyl.local
vinyl@vinyl:~ $ cd /tmp && wget https://github.com/stephencmorton/USB-Turntables-to-Sonos-with-RPi/archive/master.zip && unzip master.zip && USB-Turntables-to-Sonos-with-RPi-master/scripts/install.sh
Skip ahead to "Check if steaming is working".
Now, connect the turntable to the Raspberry Pi, using USB. You can use the command arecord -l
to check if your device has been detected. Mine shows this:
vinyl@vinyl:~ $ arecord -l
**** List of CAPTURE Hardware Devices ****
card 1: CODEC [USB AUDIO CODEC], device 0: USB Audio [USB Audio]
Subdevices: 0/1
Subdevice #0: subdevice #0
Make a note of the card number 1
in my case ("card: 1
") or even better the name ("CODEC" above). This is probably the same for you, but if it differs, you may need to remember it and change accordingly in the following steps. You will usit in the asound.conf
file below.
ALSA is the lowest-level linux sound subsystem. We're configuring the input so that darkice can use it.
As most USB turntables do not have hardware volume control, and the input volume is stuck on roughly half of what it should be, we need to add a software volume control. Create the file /etc/asound.conf and edit it to add the following contents:
pcm.dmic_hw {
type hw
# card 1
# For some reason, the card number can jump around. But this will get it by name
card CODEC
channels 2
# format S16_LE # Use this if "format dat" doesn't work. Only difference is S16_LE = 44.1 kHz sampling vs dat = 48 kHz
format dat
}
pcm.dmic_mm {
type mmap_emul
slave.pcm dmic_hw
}
pcm.dmic_sv {
type softvol
slave.pcm dmic_hw
control {
name "Boost Capture Volume"
# card 1
# For some reason, the card number can jump around. But this will get it by name
card CODEC
}
min_dB -5.0
max_dB 20.0
}
Next, run this command to refresh the alsa state and also show VU Meters to test the input volume:
arecord -D dmic_sv -r 48000 -f dat -c 2 --vumeter=stereo /dev/null
(It will show zero volume until you play something on your record player.)
You might notice, the volume is way too low. If so, you can use alsamixer
to change the volume. Press F6
to select the USB Turntable device, and press TAB
untill you see the boost slider. I have it set to 65
on my setup, but you might try out. Make sure you are not turning it up too high, or your sound quality might degrade due to clipping.
Run the following commands:
sudo apt-get update
sudo apt-get install -y darkice icecast2
Select Yes
to configure Icecast. You can leave everything as default, but if you change the password, make sure you change the password in the configuration in the next steps.
Darkice is the software that is recording from the USB device and encoding that into MP3. To configure it, create or edit the file /etc/darkice.cfg, and put this in:
# this section describes general aspects of the live streaming session
[general]
duration = 0 # duration of encoding, in seconds. 0 means forever
bufferSecs = 1 # size of internal slip buffer, in seconds
reconnect = yes # reconnect to the server(s) if disconnected
realtime = yes # run the encoder with POSIX realtime priority (default==yes)
rtprio = 4 # scheduling priority for the realtime threads (default==4)
# this section describes the audio input that will be streamed
[input]
device = dmic_sv # OSS DSP soundcard device for the audio input
sampleRate = 48000 # other settings have crackling audo, esp. 44100
bitsPerSample = 16 # bits per sample. try 16
channel = 2 # channels. 1 = mono, 2 = stereo
# this section describes a streaming connection to an IceCast2 server
# there may be up to 8 of these sections, named [icecast2-0] ... [icecast2-7]
# these can be mixed with [icecast-x] and [shoutcast-x] sections
[icecast2-0]
bitrateMode = cbr
format = mp3
bitrate = 320
server = vinyl
port = 8000
mountPoint = turntable.mp3
name = Turntable
description = Music from our record player
#highpass = 18
#lowpass = 20000
url = http://vinyl.local:8080/
genre = vinyl
public = no
password = hackme # or whatever you set your icecast2 password to
For more information about this file and the parameters you can change, see the darkice.cfg manpage.
Darkice and icecast use old-fashioned init.d controls. Let's just modernize them while we're at it.
# Remove old-fashioned init.d controls
sudo update-rc.d darkice remove
sudo update-rc.d icecast2 remove
Copy the code below to /etc/systemd/system/darkice.service and /etc/systemd/system/icecast2.service. Then run
sudo systemctl enable icecast2
sudo systemctl enable darkice
darkice.service
[Unit]
Description=DarkIce Icecast Network Audio Streamer
After=icecast.target
[Service]
Type=simple
ExecStart=/usr/bin/darkice -c /etc/darkice.cfg
ExecReload=/bin/kill -HUP $MAINPID
User=root
Group=root
#WorkingDirectory=/usr/share/icecast2/
Restart=always
RestartSec=5
[Install]
WantedBy=multi-user.target
icecast2.service
[Unit]
Description=Icecast Network Audio Streaming Server
After=network.target
[Service]
Type=simple
ExecStart=/usr/bin/icecast2 -c /etc/icecast2/icecast.xml
ExecReload=/bin/kill -HUP $MAINPID
User=icecast2
Group=icecast
#WorkingDirectory=/usr/share/icecast2/
Restart=always
[Install]
WantedBy=multi-user.target
Reboot the Raspberry Pi, to check if everything is set up correctly and because we have changed some configuration files and ensure Darkice is running.
Now open your browser, and go to http://vinyl.local:8000
(default icecast2 port). You should see a Mountpoint Mount Point /turntable.mp3
there. If not, go back and check if you did everything as described.
Right click the M3U link (upper right), and copy the link address. This is your steam URL. You can open this in iTunes, VLC, your browser, or about any other audio client that supports streaming.
Open the Sonos app on your desktop (this won't work on mobile). Go to Manage
> Add Radio Station...
and paste your stream URL. You can choose any name you want.
To play the stream on your Sonos, go to Radio by TuneIn
> My Radio Stations
. Your stream should show up there! Right-click to add to your favorites if you want! :-)
You can start playing from mobile devices, you just can't add a network stream on them.
To speed up your Raspberry Pi's boot time you can
This is left as an exercise to the reader, but there are various code snippets in fasterboot.sh to look at as well as various links in technical notes and references.
See also