github-actions[bot]
commented
2 years ago Dear jjgerber01,
we converted your machine header-file 6_pack_Shapeoko3_stepstick_XYYZ_1_SW_2_SW_3_Relay_4_5V_5_Relay.txt into a corresponding fluidNc yaml-file.
Please copy the following content into your config.yaml file and upload the file to your esp32.
name: 6 Pack ShapeOko 3 XYYZ
board: 6-pack
kinematics:
Cartesian:
stepping:
engine: I2S_stream
idle_ms: 250
dir_delay_us: 0
pulse_us: 4
disable_delay_us: 0
axes:
x:
steps_per_mm: 100.000
max_rate_mm_per_min: 1000.000
acceleration_mm_per_sec2: 200.000
max_travel_mm: 300.000
soft_limits: false
homing:
cycle: 2
mpos_mm: 0.000
positive_direction: true
settle_ms: 250.000
seek_mm_per_min: 2000.000
feed_mm_per_min: 200.000
seek_scaler: 1.100
feed_scaler: 5.000
motor0:
limit_all_pin: gpio.33
hard_limits: false
stepstick:
direction_pin: i2so.1
step_pin: i2so.2
disable_pin: i2so.0
ms3_pin: i2so.3
motor1:
null_motor:
y:
steps_per_mm: 100.000
max_rate_mm_per_min: 1000.000
acceleration_mm_per_sec2: 200.000
max_travel_mm: 300.000
soft_limits: false
homing:
cycle: 2
mpos_mm: 0.000
positive_direction: true
settle_ms: 250.000
seek_mm_per_min: 2000.000
feed_mm_per_min: 200.000
seek_scaler: 1.100
feed_scaler: 5.000
motor0:
limit_all_pin: gpio.32
hard_limits: false
stepstick:
direction_pin: i2so.4
step_pin: i2so.5
disable_pin: i2so.7
ms3_pin: i2so.6
motor1:
limit_all_pin: gpio.35
hard_limits: false
stepstick:
direction_pin: i2so.9
step_pin: i2so.10
disable_pin: i2so.8
ms3_pin: i2so.11
z:
steps_per_mm: 100.000
max_rate_mm_per_min: 1000.000
acceleration_mm_per_sec2: 200.000
max_travel_mm: 300.000
soft_limits: false
homing:
cycle: 1
mpos_mm: 0.000
positive_direction: false
settle_ms: 250.000
seek_mm_per_min: 2000.000
feed_mm_per_min: 200.000
seek_scaler: 1.100
feed_scaler: 5.000
motor0:
limit_all_pin: gpio.34
hard_limits: false
stepstick:
direction_pin: i2so.12
step_pin: i2so.13
disable_pin: i2so.15
ms3_pin: i2so.14
motor1:
null_motor:
i2so:
bck_pin: gpio.22
data_pin: gpio.21
ws_pin: gpio.17
spi:
miso_pin: gpio.19
mosi_pin: gpio.23
sck_pin: gpio.18
sdcard:
cs_pin: gpio.5
control:
safety_door_pin: gpio.2:low:pu
coolant:
flood_pin: gpio.26
mist_pin: i2so.24
delay_ms: 1000.000
probe:
pin: gpio.25:pu
check_mode_start: false
macros:
startup_line0:
startup_line1:
macro0:
macro1:
macro2:
macro3:
start:
must_home: true
check_limits: true
deactivate_parking: false
user_outputs:
PWM:
tool_num: 0
speed_map: 0=0.0% 1000=100.0%
spinup_ms: 0
spindown_ms: 0
output_pin: gpio.14
enable_pin: gpio.13
direction_pin: gpio.15
disable_with_s0: false
s0_with_disable: false
pwm_hz: 5000
arc_tolerance_mm: 0.002
junction_deviation_mm: 0.010
verbose_errors: false
report_inches: false
enable_parking_override_control: false
use_line_numbers: false 
MitchBradley
jjgerber01
This issue will automatically convert a Grbl_Esp32 machine definition file to FluidNC YAML format.
Change YOUR NAME in the title to some string that identifies your machine configuration.
IMPORTANT: Change only the YOUR NAME part of the title, not the entire title. If you change the entire title, GitHub will not run the converter program.
Attach your machine definition file here - but first change the .h extension to .txt because GitHub will not allow you to attach a file with a .h extension. Submit the issue, and after a few minutes, a new comment will appear with the FluidNC YAML file.
IMPORTANT: Attach the 6_pack_Shapeoko3_stepstick_XYYZ_1_SW_2_SW_3_Relay_4_5V_5_Relay.txt file - do not paste the file text into the issue. If you paste, the converter will not work.