github-actions[bot]
commented
2 years ago Dear SimonbJohnson,
we converted your machine header-file machine_def.txt into a corresponding fluidNc yaml-file.
Please copy the following content into your config.yaml file and upload the file to your esp32.
name: 6 Pack Trinamic 2130 1SW XYYZ 2SW AP 3 5V Laser
board: 6-pack
kinematics:
Cartesian:
stepping:
engine: I2S_stream
idle_ms: 250
dir_delay_us: 0
pulse_us: 4
disable_delay_us: 0
axes:
x:
steps_per_mm: 100.000
max_rate_mm_per_min: 1000.000
acceleration_mm_per_sec2: 200.000
max_travel_mm: 300.000
soft_limits: false
homing:
cycle: 2
mpos_mm: 0.000
positive_direction: true
settle_ms: 250.000
seek_mm_per_min: 2000.000
feed_mm_per_min: 200.000
seek_scaler: 1.100
feed_scaler: 5.000
motor0:
limit_all_pin: gpio.33:low
hard_limits: false
tmc_5160:
direction_pin: i2so.1
step_pin: i2so.2
disable_pin: i2so.0
run_amps: 0.250
hold_amps: 0.125
microsteps: 16
stallguard: 16
stallguard_debug: false
run_mode: CoolStep
homing_mode: CoolStep
use_enable: false
r_sense_ohms: 0.075
cs_pin: i2so.3:low
motor1:
null_motor:
y:
steps_per_mm: 100.000
max_rate_mm_per_min: 1000.000
acceleration_mm_per_sec2: 200.000
max_travel_mm: 300.000
soft_limits: false
homing:
cycle: 2
mpos_mm: 0.000
positive_direction: true
settle_ms: 250.000
seek_mm_per_min: 2000.000
feed_mm_per_min: 200.000
seek_scaler: 1.100
feed_scaler: 5.000
motor0:
limit_all_pin: gpio.32:low
hard_limits: false
tmc_5160:
direction_pin: i2so.4
step_pin: i2so.5
disable_pin: i2so.7
run_amps: 0.250
hold_amps: 0.125
microsteps: 16
stallguard: 16
stallguard_debug: false
run_mode: CoolStep
homing_mode: CoolStep
use_enable: false
r_sense_ohms: 0.075
cs_pin: i2so.6:low
motor1:
limit_all_pin: gpio.35:low
hard_limits: false
tmc_5160:
direction_pin: i2so.9
step_pin: i2so.10
disable_pin: i2so.8
run_amps: 0.250
hold_amps: 0.125
microsteps: 16
stallguard: 16
stallguard_debug: false
run_mode: CoolStep
homing_mode: CoolStep
use_enable: false
r_sense_ohms: 0.075
cs_pin: i2so.11:low
z:
steps_per_mm: 100.000
max_rate_mm_per_min: 1000.000
acceleration_mm_per_sec2: 200.000
max_travel_mm: 300.000
soft_limits: false
homing:
cycle: 1
mpos_mm: 0.000
positive_direction: false
settle_ms: 250.000
seek_mm_per_min: 2000.000
feed_mm_per_min: 200.000
seek_scaler: 1.100
feed_scaler: 5.000
motor0:
limit_all_pin: gpio.34:low
hard_limits: false
tmc_5160:
direction_pin: i2so.12
step_pin: i2so.13
disable_pin: i2so.15
run_amps: 0.250
hold_amps: 0.125
microsteps: 16
stallguard: 16
stallguard_debug: false
run_mode: CoolStep
homing_mode: CoolStep
use_enable: false
r_sense_ohms: 0.075
cs_pin: i2so.14:low
motor1:
null_motor:
a:
steps_per_mm: 100.000
max_rate_mm_per_min: 1000.000
acceleration_mm_per_sec2: 200.000
max_travel_mm: 300.000
soft_limits: false
motor0:
limit_all_pin: gpio.39:low
hard_limits: false
tmc_5160:
direction_pin: i2so.17
step_pin: i2so.18
disable_pin: i2so.16
run_amps: 0.250
hold_amps: 0.125
microsteps: 16
stallguard: 16
stallguard_debug: false
run_mode: CoolStep
homing_mode: CoolStep
use_enable: false
r_sense_ohms: 0.075
cs_pin: i2so.19:low
motor1:
null_motor:
b:
steps_per_mm: 100.000
max_rate_mm_per_min: 1000.000
acceleration_mm_per_sec2: 200.000
max_travel_mm: 300.000
soft_limits: false
motor0:
null_motor:
motor1:
null_motor:
c:
steps_per_mm: 100.000
max_rate_mm_per_min: 1000.000
acceleration_mm_per_sec2: 200.000
max_travel_mm: 300.000
soft_limits: false
motor0:
null_motor:
motor1:
null_motor:
i2so:
bck_pin: gpio.22
data_pin: gpio.21
ws_pin: gpio.17
spi:
miso_pin: gpio.19
mosi_pin: gpio.23
sck_pin: gpio.18
sdcard:
cs_pin: gpio.5
control:
coolant:
flood_pin: gpio.27
mist_pin: gpio.16
delay_ms: 1000.000
probe:
pin: gpio.36:low
check_mode_start: false
macros:
startup_line0:
startup_line1:
macro0:
macro1:
macro2:
macro3:
start:
must_home: true
check_limits: true
deactivate_parking: false
user_outputs:
laser:
tool_num: 0
speed_map: 0=0.0% 1000=100.0%
output_pin: gpio.26
enable_pin: gpio.4
disable_with_s0: false
s0_with_disable: false
pwm_hz: 5000
arc_tolerance_mm: 0.002
junction_deviation_mm: 0.010
verbose_errors: false
report_inches: false
enable_parking_override_control: false
use_line_numbers: false
This issue will automatically convert a Grbl_Esp32 machine definition file to FluidNC YAML format.
Change YOUR NAME in the title to some string that identifies your machine configuration.
IMPORTANT: Change only the YOUR NAME part of the title, not the entire title. If you change the entire title, GitHub will not run the converter program.
Attach your machine definition file here - but first change the .h extension to .txt because GitHub will not allow you to attach a file with a .h extension. Submit the issue, and after a few minutes, a new comment will appear with the FluidNC YAML file.
IMPORTANT: Attach the file - do not paste the file text into the issue. If you paste, the converter will not work. machine_def.txt