issues
search
bummbummgarage
/
bummbummgarage.github.io
5
stars
2
forks
source link
issues
Newest
Newest
Most commented
Recently updated
Oldest
Least commented
Least recently updated
[Envelope Generator 0.1] Sustain not stable
#63
teariceneptune
opened
1 year ago
0
[Envelope Generator 0.1] Add diode before switch
#62
teariceneptune
opened
1 year ago
0
[VCF Rev4] Move IC headers before Caps in BOM (soldering sequence)
#61
teariceneptune
opened
1 year ago
0
[VCF Rev4] Put Power decoupling caps on the other side
#60
teariceneptune
opened
1 year ago
0
[Mixer II Rev4] In the schematic the attenuator is 1k and in the BOM 5k
#59
teariceneptune
opened
2 years ago
1
[Clock Multiplier Rev2] Make ISP upload without power supply possible
#58
teariceneptune
opened
2 years ago
0
[Clock Multiplier Rev2] 10uF are too crowded
#57
teariceneptune
opened
2 years ago
0
[Clock Multiplier Rev2] Rename OpAmp to "IC…"
#56
teariceneptune
opened
2 years ago
0
[VCF Rev4] Out circle could be bit bigger, seems off behind the nut
#55
teariceneptune
opened
2 years ago
0
[VCF Rev4] Move connector footprints to the back on the Control Board
#54
teariceneptune
opened
2 years ago
0
[Mixer II Rev4] Output no GND
#53
teariceneptune
opened
2 years ago
0
[Mixer II Rev4] ⚡️ Make it real 2hp wide
#52
teariceneptune
opened
2 years ago
0
[Mixer II Rev4] Add black circle around output on panel
#51
teariceneptune
opened
2 years ago
0
[Mixer II Rev4] Optimize position of screw holes
#50
teariceneptune
opened
2 years ago
0
[ENVF Rev4] Consider Mickys suggestions
#49
teariceneptune
opened
2 years ago
0
[VCEG Rev2] Correct "thermal settings" for pads on ground copper pour
#48
teariceneptune
opened
2 years ago
0
[ENVF Rev4] Release always has to be at maximum
#47
teariceneptune
opened
2 years ago
0
[ENVF Rev4] RV2 (support) legs are too close to J9
#46
teariceneptune
opened
2 years ago
0
[ENVF Rev4] Insufficient spacing around IC
#45
threedaymonk
opened
2 years ago
3
[VCEG Rev2] Add black circle around output jacks
#44
teariceneptune
closed
2 years ago
1
[ENVF Rev4] J1 silkscreen on wrong side
#43
threedaymonk
opened
2 years ago
0
[VCF Rev4] PCBs and panel updates (WEEE, CE, …)
#42
teariceneptune
closed
2 years ago
1
[VCF Rev4] Mark outputs on the panel
#41
teariceneptune
closed
2 years ago
0
[VCEG Rev2] Mark outputs on the panel
#40
teariceneptune
opened
2 years ago
0
[VCEG Rev2] Problems with calibrating
#39
teariceneptune
opened
2 years ago
0
[VCEG Rev2] Get general learnings from the modules before
#38
teariceneptune
opened
2 years ago
0
[VCEG Rev2] Tight fit on the three potentiometer through holes
#37
teariceneptune
opened
2 years ago
0
[ENVF Rev3] Remove issue link from project page when all done
#36
teariceneptune
closed
2 years ago
0
[ENVF Rev3] Cross check all learnings for issues here
#35
teariceneptune
closed
2 years ago
0
[ENVF Rev3] Add dedication on the panel back
#34
teariceneptune
closed
2 years ago
0
[ENVF Rev3] Check general PCBs labels
#33
teariceneptune
closed
2 years ago
0
[VCF Rev3] Remove issue link from website when all issues are done
#32
teariceneptune
closed
2 years ago
1
[VCF Rev3] Create Build Doc
#31
teariceneptune
closed
2 years ago
0
[VCF Rev4] Check (and update) BOM
#30
teariceneptune
closed
2 years ago
0
[VCF Rev3] Updated description on all boards
#29
teariceneptune
closed
2 years ago
0
[VCF Rev3] Logo and bin icon on all boards
#28
teariceneptune
closed
2 years ago
0
[VCF Rev3] Version on the back of panel
#27
teariceneptune
closed
2 years ago
1
[VCF Rev3] Panel: New logo and Cutoff in the middle
#26
teariceneptune
closed
2 years ago
0
[VCF Rev3] Check width with Doepfer specs
#25
teariceneptune
closed
2 years ago
1
[ENVF Rev3] Make 9.8mm wide and adjust panel hole
#24
teariceneptune
closed
2 years ago
0
[VCEG Rev2] Mounting holes are out of spec
#23
teariceneptune
opened
2 years ago
2
[VCEG Rev2] Potentiometer holes for legs and support arms are too tight
#22
teariceneptune
closed
2 years ago
1
[VCF Rev3] Change switch to mini version that is more available and less expensive
#21
teariceneptune
closed
2 years ago
5
[VCF Rev3] Extract VCF general learnings for the upcoming modules
#20
teariceneptune
closed
2 years ago
0
[VCEG Rev2] Build Doc: make left and right trimmer screw more clear in calibration section
#19
teariceneptune
opened
2 years ago
0
[ENVF Rev3] Diodes for reverse polarity power protection
#18
pansapiens
closed
2 years ago
1
[ENVF Rev3] LED should be driven by transistor
#17
teariceneptune
closed
2 years ago
1
[Mixer II Rev3] dual color led
#16
teariceneptune
opened
2 years ago
2
[VCF Rev3] Technical font on PCB just as Thonk has it
#15
teariceneptune
closed
2 years ago
1
[VCF Rev3] Module's to deep for skiffycases
#14
teariceneptune
closed
2 years ago
2
Next