NX-595E Output Control Fork

This fork is designated to implementing the "Output Control" section of the NX-595E. The main objective is to enable communication with the outputs and ensure its proper implementation.

NX-595E UltraSync Hub

Compatible with both NX-595E Hills ComNav, xGen, xGen8 (such as NXG-8-Z-BO), Interlogix, and ZeroWire UltraSync solutions.

How Does It Work?

1. First you need to install it; this part is easy:

   # Install ultrasync onto your system
   pip install ultrasync

2. Create a configuration file that identifies:

   1. The hostname or IP address of the ComNav/ZeroWire hub you've got setup on some the network.
   2. Your ComNav/ZeroWire login User ID.
   3. Your ComNav/ZeroWire login pin.

   Note: You can only be logged into the ComNav/ZeroWire hub with the same user once; a subsequent login with the same user logs out the other. Since this tool/software actively polls and maintains a login session to your Hub, it can prevent you from being able to log into at the same time elsewhere (via it's website). It is strongly recommended that you create a second user account on your Hub dedicated to just this service.

   # An example of what would be found in your configuration file:
   # Use hashtags/pound symbols (#) to optionally add comments
   # Syntax is simply <key>: <value>
   #
   # You must specify a ip/hostname, user, and pin
   #
   host: 192.168.0.30
   user: My Username
   pin: 1234

3. Use the --scene (-s) to set your security system's alarm scene. The possible options are: disarm, away, and stay.

   # By default if no --config= (-c) is specified, one will be automatically
   # loaded from the following location (if present):
   #  ~/.ultrasync
   #  ~/.config/ultrasync
   
   # Windows users can store their default configuration files here:
   #  %APPDATA%/UltraSync/config
   #  %LOCALAPPDATA%/UltraSync/config
   
   # Disarm your security system
   ultrasync --scene disarm
   
   # Arm your security system and activate all of your sensors when setting the
   # away mode macro
   ultrasync --scene away
   
   # Arm your security system and only activate your perimeter sensors:
   ultrasync --scene stay

What Else Can It Do?

• You can put up a live monitor of your device by typing the following:

  # A live monitoring of your home security system:
  ultrasync --watch

  

• You can generate a snapshot (in JSON format) that greatly details everything taking place through your security home setup. It provides MUCH greater detail than the --watch which allows it to also be integrated with Home Assistant.

  # Print a JSON formatted snapshot of all home security details
  ultrasync --details

• You can perform a dump of all of the web based files (that I've found to be useful so far) to disk. This makes troubleshooting much easier.

  # Extracts information from your UltraSync Hub that can be
  # incredibly useful in debugging and/or adding enhancements
  # later on:
  ultrasync --debug-dump

  The debug content gets written to a zip file (residing in the same folder you ran this command from) in the form of: YYYYmmddHHMMSS.ultrasync-dump.zip.

Reverse Proxy

If you've exposed your panel to the internet, you can access it by setting your host to the full URL to it (instead of just the hosthame/ip). For example:

# A sample UltraSync configuration that requires you to pass through
# a proxy in order to get to your destination:
host: https://your.security.panel/
user: My Username
pin: 1234

If you've also protected your panel behind an additional user/pass combo using Basic Auth at the reverse proxy level, you can pass through it like so:

# A sample ultrasync configuration that requires you to pass through
# a proxy expecting authentication in order to get to your destination:
host: https://user:pass@your.security.panel/
user: My Username
pin: 1234
# You can also optionally turn off the secure hostname verification
# by using the verify switch.  But default this is set to yes if not
# specified:
verify: no

Global Variables

You can also (optionally) set the following global variables to provide the equivalent of what the configuration file could have. If a configuration file is also loaded, it's settings will always prevail. If an entry is missing, then the environment variable is used instead (if it's defined):

Disclaimer

This software was created by reverse engineering my own personal security system. All of this code was generated through trial and error since there is no documentation that I could find that explains the registers. If you can help out by filling in some of the blanks throughout the code base, I would be greatly appreciative of it! Alternatively buying me a coffee greatly inspires me to continue improving the application.