Lambda run script, using Netbox as a source of truth to integrate ip/dns pairs into Route53 via webhook and on a schedule basis.
Netbox-Route53 is a python script that is used to sync Route53 records with Netbox. This script uses webhooks for instant updating, as well as an integration function that runs on an hourly and daily timer to fully sync up records.
Netbox record id's are permanently unique, so when the script adds records to Route53, it creates an accompanying txt record with a special identifier tag as well as the Netbox record id. This prevents the script from updating records that it hasn't created and ensures that it always updates the correct record inside of Route53. (The id is seen as the only identifier for a record)
The webhooks work by having Netbox configured to send events to the script anytime a record in Netbox is created, updated or deleted. The script parses these webhooks and decides what action to take based on the type of event (c/u/d). Only records with the special txt identifier record will be modified.
The timer based portion of the script will integrate records from Netbox to Route53 based on a timespan variable. This retrieves the newer records in Netbox and compares them to what is in Route53, following the same create/update/delete logic as webhooks for each record. After integrating all the records, the script purges any Route53 record that has a tag, but is not present in Netbox. This is to prevent stale records from hanging around.
To quickly compare a large number of records and minimize on script uptime, all Netbox records are retrieved in 1 api call and stored in a dictionary as mapped key values. The hosted zones are parsed from the Netbox record names so only the necessary hosted zone records are retrieved and put into a key value mapping for Route53 records.
The script then iterates through these two dictionaries, determining what to do for each Netbox record, then formulates the update in json, finishing by storing it in a changebatch variable which contains all the changes to be sent to Route53 in a single api batch call.
The purging function (clean_r53_records) works in a similar manner, however it calls Netbox and Route53 again, to get an up-to-date snapshot post integration.
Example of the three different type of key value mappings used:
All 3 keys contain value pairs that give extra information about a record.
Txt keys are built to check if an A record has an accompanying txt record which then can be checked for presence of the tag, and the Netbox id. A keys (dns and ip) are necessary to check if a record exists already. Dns and ip need to be separate because duplicates of either kind are not supported by script logic.
Keys are generated and stored in a dictionary every time the script starts. For every record the script checks, it generates a new key and checks the dict it created to see if the key is present.
To prepare the framework inside AWS LAMBDA for uploading the script via Makefile commands
-Create a lambda function, appropriately named (Use Python version 3.8)
-Aws Cloudwatch Trigger Setup
(Start from step 2, set timer to run every 30 minutes)
To store the timespan within cloudwatch timer for multiple timer use, under targets, constant(json text) paste the following: {"Timespan": "1" } (note, any other cloudwatch timers will be set up the same but with different time spans)
If there is no cloudwatch timespan set, or is set incorrectly, the script will use the environment variable "TIMESPAN"
-Aws API Gateway Trigger Setup
(For the Netbox setup below, you will need the AWS API gateway Arn from creating an api gateway trigger)
To enable Netbox webhooks:
Netbox>Other>Webhooks>Add Webhook
Name: ()
Object types: (IP addess, prefix)
Enabled: (checked)
Type Create: (checked)
Type Update: (checked)
Type Delete: (checked)
URL: (AWS API gateway arn) < (See Api gateway trigger setup)
HTTP method: (POST)
HTTP content type: (application/json)
The following environment variables need to be added to the lambda function NETBOX_TIMESPAN: 1 NETBOX_TOKEN: (access token for Netbox) NETBOX_URL: (url for Netbox) ROUTE53_ID: See IAM user setup below ROUTE53_KEY: See IAM user setup below ROUTE53_TAG: nbr53
An aws IAM user needs to be created and the access key/secret key are put in as env vars in the order ROUTE53_ID = access key | ROUTE53_KEY: secret key
The IAM user needs to have the following policies attached:
To push script to lamdba, use Makefile commands
Rename LAMBDA_FUNCTION_NAME inside the makefile to match the name of the Aws Lambda function
(Terminal/Cmd commands to port script to aws)
-Specify Aws account details
aws configure
aws sts get-caller-identity-Compile Script and upload to both functions
make lambda-layer
make lambda-upload