ORP Sensor

[umchemist]

Hi!

This is a great add-on, far better than the Hayward app. For example, I can get the air temp reading!

I've have a pH and ORP set up, along with an ozone set up. Welcome the opportunity to contribute and get the pH/ORP values into this.

Please reach out.

[daytonturner]

I'm about to take a stab at adding these as well, will update here if I make any progress - also interested in getting detail beyond what the "official" cloud integration does which is simply show you the current pH and current ORP reading - I'd like to know when the chlorinator is actually chlorinating, what the target mV is, if the heater is heating, and ideally diagnostic data from each of the components which the app can access (including errors/warning notifications)

[umchemist]

Awesome, please let me know how I can help ! Some thoughts:

• The pH/ORP controls just a high voltage relay
• pH calibration is just a single point (odd, most are two or three points)
• Is there an ability to control the run time of the relay? That's not seen anywhere, but could be handy when using CO2 or a strong acid to pump and reduce pH.

On Wed, Jul 24, 2024 at 1:41 PM daytonturner @.***> wrote:

I'm about to take a stab at adding these as well, will update here if I make any progress - also interested in getting detail beyond what the "official" cloud integration does which is simply show you the current pH and current ORP reading - I'd like to know when the chlorinator is actually chlorinating, what the target mV is, if the heater is heating, and ideally diagnostic data from each of the components which the app can access (including errors/warning notifications)

— Reply to this email directly, view it on GitHub https://github.com/cryptk/haomnilogic-local/issues/116#issuecomment-2248676835, or unsubscribe https://github.com/notifications/unsubscribe-auth/AB2UNKEUXRDA5W2NT3REIDTZN7YN5AVCNFSM6AAAAABLF6RLOSVHI2DSMVQWIX3LMV43OSLTON2WKQ3PNVWWK3TUHMZDENBYGY3TMOBTGU . You are receiving this because you authored the thread.Message ID: @.***>

[krucka]

I recently had my 1yr old SWG go out and now that I have my warranty replacement, was looking for a way to have better trending on the diagnostic reporting from the chlorinator. I have a TurboCell TCellS340W and am willing to help test if necessary. In the Android Omnilogic app, the same diagnostic window that shows instant and average salt (which already shows up in home assistant) shows: -Cell Temp -Cell Current -Cell Voltage -Relay Polarity From the local controller, there are other values as well such as board temp, that would also be nice to add.

[cryptk]

There should be a PH sensor already and ORP should be shown as an attribute on that PH sensor. I already plan to split the ORP data out to it's own sensor though as part of #106

If you don't have a pH sensor, can you please attach the diagnostic data from the addon to this issue so that I can look into it when I have time?

[umchemist]

Sounds great, unfortunately Im not seeing a pH sensor in the 7.5 build. Attached is the diagnostic data.

On Tue, Jul 30, 2024 at 11:48 AM cryptk @.***> wrote:

There should be a PH sensor already and ORP should be shown as an attribute on that PH sensor. I already plan to split the ORP data out to it's own sensor though as part of #106 https://github.com/cryptk/haomnilogic-local/issues/106

If you don't have a pH sensor, can you please attach the diagnostic data from the addon to this issue so that I can look into it when I have time?

— Reply to this email directly, view it on GitHub https://github.com/cryptk/haomnilogic-local/issues/116#issuecomment-2258786337, or unsubscribe https://github.com/notifications/unsubscribe-auth/AB2UNKF5E4O6AIHBCFZNNLDZO67WJAVCNFSM6AAAAABLF6RLOSVHI2DSMVQWIX3LMV43OSLTON2WKQ3PNVWWK3TUHMZDENJYG44DMMZTG4 . You are receiving this because you authored the thread.Message ID: @.***>

[cryptk]

There is not attachment to that comment. I don't know if attachments work with email replies, you might need to attach it in the GitHub UI itself

[umchemist]

Right- sorry about that. File now attached. config_entry-omnilogic_local-01J384ZFW1R0K0GS7NBM7NRQ0C(1).json