search

ctag-fh-kiel / ctag-straempler

An open source eurorack sample streaming and sound synthesis module.
Other
117 stars 21 forks source link

diskio_sdmmc: sdmmc_read_blocks failed #18

Closed polymer81 closed 2 years ago

polymer81 commented 2 years ago

Hi.

I have only tried with one SD card but this looks like there is a problem with it I guess. When I use the flash.sh file, the files are written to the card and the SD examples work fine. This is the serial monitor output :

rst:0x1 (POWERON_RESET),boot:0x1b (SPI_FAST_FLASH_BOOT) configsip: 0, SPIWP:0xee clk_drv:0x00,q_drv:0x00,d_drv:0x00,cs0_drv:0x00,hd_drv:0x00,wp_drv:0x00 mode:DIO, clock div:2 load:0x3fff0030,len:4 load:0x3fff0034,len:7316 load:0x40078000,len:14252 load:0x40080400,len:4688 entry 0x400806a4 I (28) boot: ESP-IDF v4.1.2-95-gaeb66e1057 2nd stage bootloader I (28) boot: compile time 09:31:00 I (28) boot: chip revision: 1 I (32) boot_comm: chip revision: 1, min. bootloader chip revision: 0 I (39) qio_mode: Enabling default flash chip QIO I (44) boot.esp32: SPI Speed : 40MHz I (49) boot.esp32: SPI Mode : QIO I (53) boot.esp32: SPI Flash Size : 4MB I (58) boot: Enabling RNG early entropy source... I (63) boot: Partition Table: I (67) boot: ## Label Usage Type ST Offset Length I (74) boot: 0 nvs WiFi data 01 02 00009000 00006000 I (82) boot: 1 phy_init RF data 01 01 0000f000 00001000 I (89) boot: 2 factory factory app 00 00 00010000 00200000 I (97) boot: End of partition table I (101) boot_comm: chip revision: 1, min. application chip revision: 0 I (108) esp_image: segment 0: paddr=0x00010020 vaddr=0x3f400020 size=0x2f0f0 (192752) map I (187) esp_image: segment 1: paddr=0x0003f118 vaddr=0x3ffb0000 size=0x00f00 ( 3840) load I (189) esp_image: segment 2: paddr=0x00040020 vaddr=0x400d0020 size=0xc7854 (817236) map I (491) esp_image: segment 3: paddr=0x0010787c vaddr=0x3ffb0f00 size=0x05628 ( 22056) load I (501) esp_image: segment 4: paddr=0x0010ceac vaddr=0x40080000 size=0x00404 ( 1028) load I (501) esp_image: segment 5: paddr=0x0010d2b8 vaddr=0x40080404 size=0x1e134 (123188) load I (579) boot: Loaded app from partition at offset 0x10000 I (579) boot: Disabling RNG early entropy source... I (580) psram: This chip is ESP32-D0WD I (584) spiram: Found 64MBit SPI RAM device I (589) spiram: SPI RAM mode: flash 80m sram 80m I (594) spiram: PSRAM initialized, cache is in low/high (2-core) mode. I (601) cpu_start: Pro cpu up. I (605) cpu_start: Application information: I (610) cpu_start: Project name: ctag-straempler I (616) cpu_start: App version: v0.9 I (620) cpu_start: Compile time: Sep 11 2021 09:54:10 I (626) cpu_start: ELF file SHA256: 32bab0cc5eb6c006... I (632) cpu_start: ESP-IDF: v4.1.2-95-gaeb66e1057 I (638) cpu_start: Starting app cpu, entry point is 0x40081720 I (0) cpu_start: App cpu up. I (1121) spiram: SPI SRAM memory test OK I (1121) heap_init: Initializing. RAM available for dynamic allocation: I (1121) heap_init: At 3FFAE6E0 len 00001920 (6 KiB): DRAM I (1128) heap_init: At 3FFBEEB0 len 00021150 (132 KiB): DRAM I (1134) heap_init: At 3FFE0440 len 00003AE0 (14 KiB): D/IRAM I (1140) heap_init: At 3FFE4350 len 0001BCB0 (111 KiB): D/IRAM I (1147) heap_init: At 4009E538 len 00001AC8 (6 KiB): IRAM I (1153) cpu_start: Pro cpu start user code I (1158) spiram: Adding pool of 4096K of external SPI memory to heap allocator I (1178) spi_flash: detected chip: generic I (1178) spi_flash: flash io: qio I (1178) cpu_start: Starting scheduler on PRO CPU. I (0) cpu_start: Starting scheduler on APP CPU. I (1188) SD: Initializing SD card I (1188) gpio: GPIO[13]| InputEn: 0| OutputEn: 1| OpenDrain: 0| Pullup: 0| Pulldown: 0| Intr:0  Name: SD64G Type: SDHC/SDXC Speed: 40 MHz Size: 59640MB SPI: display device added to spi bus (1)

SPI: attached display device, speed=8000000

SPI: bus uses native pins: false

SPI: display init...

OK

SPI: Max rd speed = 1000000

SPI: Changed speed to 26666666

I (2688) gpio: GPIO[33]| InputEn: 1| OutputEn: 0| OpenDrain: 0| Pullup: 0| Pulldown: 0| Intr:2  I (2688) gpio: GPIO[34]| InputEn: 1| OutputEn: 0| OpenDrain: 0| Pullup: 0| Pulldown: 0| Intr:2  I (2698) gpio: GPIO[35]| InputEn: 1| OutputEn: 0| OpenDrain: 0| Pullup: 0| Pulldown: 0| Intr:2  I (2708) gpio: GPIO[36]| InputEn: 1| OutputEn: 0| OpenDrain: 0| Pullup: 0| Pulldown: 0| Intr:0  I (2718) gpio: GPIO[39]| InputEn: 1| OutputEn: 0| OpenDrain: 0| Pullup: 0| Pulldown: 0| Intr:0  I (2728) AUDIO: Starting audio task I (2728) I2S: DMA Malloc info, datalen=blocksize=256, dma_buf_count=4 I (2738) I2S: DMA Malloc info, datalen=blocksize=256, dma_buf_count=4 I (2758) I2S: APLL: Req RATE: 44100, real rate: 44099.988, BITS: 32, CLKM: 1, BCK_M: 8, MCLK: 22579194.000, SCLK: 2822399.250000, diva: 1, divb: 0 E (2798) sdmmc_cmd: sdmmc_read_sectors_dma: sdmmc_send_cmd returned 0x109 E (2798) diskio_sdmmc: sdmmc_read_blocks failed (265) E (2798) FILEIO: Error reading from file E (2798) PRESET: Root is NULL E (2808) MENU: Error loading bank from file E (2808) MENU: Error loading bank E (2818) sdmmc_cmd: sdmmc_read_sectors_dma: sdmmc_send_cmd returned 0x107 E (2818) diskio_sdmmc: sdmmc_read_blocks failed (263) E (2828) FILEIO: Could not allocate memory E (2828) MENU: Error loading tz_shift from config I (2988) wifi:wifi driver task: 3ffe9e1c, prio:23, stack:6656, core=0 I (2988) system_api: Base MAC address is not set, read default base MAC address from BLK0 of EFUSE I (2988) system_api: Base MAC address is not set, read default base MAC address from BLK0 of EFUSE I (3008) wifi:wifi firmware version: 1424aca I (3008) wifi:config NVS flash: enabled I (3008) wifi:config nano formating: disabled I (3008) wifi:Init data frame dynamic rx buffer num: 32 I (3018) wifi:Init management frame dynamic rx buffer num: 32 I (3018) wifi:Init management short buffer num: 32 I (3028) wifi:Init static tx buffer num: 16 I (3028) wifi:Init static rx buffer size: 1600 I (3038) wifi:Init static rx buffer num: 10 I (3038) wifi:Init dynamic rx buffer num: 32 I (3048) wifi_init: rx ba win: 16 I (3048) wifi_init: tcpip mbox: 32 I (3048) wifi_init: udp mbox: 6 I (3058) wifi_init: tcp mbox: 6 I (3058) wifi_init: tcp tx win: 5744 I (3068) wifi_init: tcp rx win: 5744 I (3068) wifi_init: tcp mss: 1440 I (3068) wifi_init: WiFi/LWIP prefer SPIRAM I (3078) wifi_init: WiFi IRAM OP enabled I (3078) wifi_init: WiFi RX IRAM OP enabled E (3088) sdmmc_req: handle_idle_state_events unhandled: 00000008 00000002 I (3098) WIFI: Setting WiFi configuration SSID Fantasy Man I (3098) phy_init: phy_version 4660,0162888,Dec 23 2020 W (3108) phy_init: failed to load RF calibration data (0x1102), falling back to full calibration ets Jun 8 2016 00:22:57

rst:0x1 (POWERON_RESET),boot:0x1b (SPI_FAST_FLASH_BOOT) configsip: 0, SPIWP:0⸮⸮半⸮⸮⸮_drv:0x00,q_drv:0x00,d_drv:0x00,c⸮ߤ⸮⸮⸮⸮⸮⸮⸮⸮hd_drv:0x00,wp_drv:0x00 mode:DIO, clock div:2 load:0x3fff0030,len:4 load:0x3fff0034,len:7316 load:0x40078000,len:14252 load:0x40080400,len:4688 entry 0x400806a4 I (28) boot: ESP-IDF v4.1.2-95-gaeb66e1057 2nd stage bootloader I (28) boot: compile time 09:31:00 I (28) boot: chip revision: 1 I (32) boot_comm: chip revision: 1, min. bootloader chip revision: 0 I (39) qio_mode: Enabling default flash chip QIO I (44) boot.esp32: SPI Speed : 40MHz I (49) boot.esp32: SPI Mode : QIO I (53) boot.esp32: SPI Flash Size : 4MB I (58) boot: Enabling RNG early entropy source... I (63) boot: Partition Table: I (67) boot: ## Label Usage Type ST Offset Length I (74) boot: 0 nvs WiFi data 01 02 00009000 00006000 I (82) boot: 1 phy_init RF data 01 01 0000f000 00001000 I (89) boot: 2 factory factory app 00 00 00010000 00200000 I (97) boot: End of partition table I (101) boot_comm: chip revision: 1, min. application chip revision: 0 I (108) esp_image: segment 0: paddr=0x00010020 vaddr=0x3f400020 size=0x2f0f0 (192752) map I (187) esp_image: segment 1: paddr=0x0003f118 vaddr=0x3ffb0000 size=0x00f00 ( 3840) load I (189) esp_image: segment 2: paddr=0x00040020 vaddr=0x400d0020 size=0xc7854 (817236) map I (491) esp_image: segment 3: paddr=0x0010787c vaddr=0x3ffb0f00 size=0x05628 ( 22056) load I (501) esp_image: segment 4: paddr=0x0010ceac vaddr=0x40080000 size=0x00404 ( 1028) load I (501) esp_image: segment 5: paddr=0x0010d2b8 vaddr=0x40080404 size=0x1e134 (123188) load I (579) boot: Loaded app from partition at offset 0x10000 I (579) boot: Disabling RNG early entropy source... I (580) psram: This chip is ESP32-D0WD I (584) spiram: Found 64MBit SPI RAM device I (589) spiram: SPI RAM mode: flash 80m sram 80m I (594) spiram: PSRAM initialized, cache is in low/high (2-core) mode. I (601) cpu_start: Pro cpu up. I (605) cpu_start: Application information: I (610) cpu_start: Project name: ctag-straempler I (616) cpu_start: App version: v0.9 I (620) cpu_start: Compile time: Sep 11 2021 09:54:10 I (626) cpu_start: ELF file SHA256: 32bab0cc5eb6c006... I (632) cpu_start: ESP-IDF: v4.1.2-95-gaeb66e1057 I (638) cpu_start: Starting app cpu, entry point is 0x40081720 I (0) cpu_start: App cpu up. I (1121) spiram: SPI SRAM memory test OK I (1121) heap_init: Initializing. RAM available for dynamic allocation: I (1121) heap_init: At 3FFAE6E0 len 00001920 (6 KiB): DRAM I (1128) heap_init: At 3FFBEEB0 len 00021150 (132 KiB): DRAM I (1134) heap_init: At 3FFE0440 len 00003AE0 (14 KiB): D/IRAM I (1140) heap_init: At 3FFE4350 len 0001BCB0 (111 KiB): D/IRAM I (1147) heap_init: At 4009E538 len 00001AC8 (6 KiB): IRAM I (1153) cpu_start: Pro cpu start user code I (1158) spiram: Adding pool of 4096K of external SPI memory to heap allocator I (1178) spi_flash: detected chip: generic I (1178) spi_flash: flash io: qio I (1178) cpu_start: Starting scheduler on PRO CPU. I (0) cpu_start: Starting scheduler on APP CPU. I (1188) SD: Initializing SD card I (1188) gpio: GPIO[13]| InputEn: 0| OutputEn: 1| OpenDrain: 0| Pullup: 0| Pulldown: 0| Intr:0  Name: SD64G Type: SDHC/SDXC Speed: 40 MHz Size: 59640MB SPI: display device added to spi bus (1)

SPI: attached display device, speed=8000000

SPI: bus uses native pins: false

SPI: display init...

I guess I should try another SD card ?

Thanks :)

ctag-fh-kiel commented 2 years ago

Check all solder points, try another SD card, could well be a cold solder point, I'd say...

On Wed, Jan 26, 2022 at 10:45 PM polymer81 @.***> wrote:

Hi.

I have only tried with one SD card but this looks like there is a problem with it I guess. When I use the flash.sh file, the files are written to the card and the SD examples work fine. This is the serial monitor output :

rst:0x1 (POWERON_RESET),boot:0x1b (SPI_FAST_FLASH_BOOT) configsip: 0, SPIWP:0xee clk_drv:0x00,q_drv:0x00,d_drv:0x00,cs0_drv:0x00,hd_drv:0x00,wp_drv:0x00 mode:DIO, clock div:2 load:0x3fff0030,len:4 load:0x3fff0034,len:7316 load:0x40078000,len:14252 load:0x40080400,len:4688 entry 0x400806a4 �[0;32mI (28) boot: ESP-IDF v4.1.2-95-gaeb66e1057 2nd stage bootloader�[0m �[0;32mI (28) boot: compile time 09:31:00�[0m �[0;32mI (28) boot: chip revision: 1�[0m �[0;32mI (32) boot_comm: chip revision: 1, min. bootloader chip revision: 0�[0m �[0;32mI (39) qio_mode: Enabling default flash chip QIO�[0m �[0;32mI (44) boot.esp32: SPI Speed : 40MHz�[0m �[0;32mI (49) boot.esp32: SPI Mode : QIO�[0m �[0;32mI (53) boot.esp32: SPI Flash Size : 4MB�[0m �[0;32mI (58) boot: Enabling RNG early entropy source...�[0m �[0;32mI (63) boot: Partition Table:�[0m �[0;32mI (67) boot: ## Label Usage Type ST Offset Length�[0m �[0;32mI (74) boot: 0 nvs WiFi data 01 02 00009000 00006000�[0m �[0;32mI (82) boot: 1 phy_init RF data 01 01 0000f000 00001000�[0m �[0;32mI (89) boot: 2 factory factory app 00 00 00010000 00200000�[0m �[0;32mI (97) boot: End of partition table�[0m �[0;32mI (101) boot_comm: chip revision: 1, min. application chip revision: 0�[0m �[0;32mI (108) esp_image: segment 0: paddr=0x00010020 vaddr=0x3f400020 size=0x2f0f0 (192752) map�[0m �[0;32mI (187) esp_image: segment 1: paddr=0x0003f118 vaddr=0x3ffb0000 size=0x00f00 ( 3840) load�[0m �[0;32mI (189) esp_image: segment 2: paddr=0x00040020 vaddr=0x400d0020 size=0xc7854 (817236) map�[0m �[0;32mI (491) esp_image: segment 3: paddr=0x0010787c vaddr=0x3ffb0f00 size=0x05628 ( 22056) load�[0m �[0;32mI (501) esp_image: segment 4: paddr=0x0010ceac vaddr=0x40080000 size=0x00404 ( 1028) load�[0m �[0;32mI (501) esp_image: segment 5: paddr=0x0010d2b8 vaddr=0x40080404 size=0x1e134 (123188) load�[0m �[0;32mI (579) boot: Loaded app from partition at offset 0x10000�[0m �[0;32mI (579) boot: Disabling RNG early entropy source...�[0m �[0;32mI (580) psram: This chip is ESP32-D0WD�[0m �[0;32mI (584) spiram: Found 64MBit SPI RAM device�[0m �[0;32mI (589) spiram: SPI RAM mode: flash 80m sram 80m�[0m �[0;32mI (594) spiram: PSRAM initialized, cache is in low/high (2-core) mode.�[0m �[0;32mI (601) cpu_start: Pro cpu up.�[0m �[0;32mI (605) cpu_start: Application information:�[0m �[0;32mI (610) cpu_start: Project name: ctag-straempler�[0m �[0;32mI (616) cpu_start: App version: v0.9�[0m �[0;32mI (620) cpu_start: Compile time: Sep 11 2021 09:54:10�[0m �[0;32mI (626) cpu_start: ELF file SHA256: 32bab0cc5eb6c006...�[0m �[0;32mI (632) cpu_start: ESP-IDF: v4.1.2-95-gaeb66e1057�[0m �[0;32mI (638) cpu_start: Starting app cpu, entry point is 0x40081720�[0m �[0;32mI (0) cpu_start: App cpu up.�[0m �[0;32mI (1121) spiram: SPI SRAM memory test OK�[0m �[0;32mI (1121) heap_init: Initializing. RAM available for dynamic allocation:�[0m �[0;32mI (1121) heap_init: At 3FFAE6E0 len 00001920 (6 KiB): DRAM�[0m �[0;32mI (1128) heap_init: At 3FFBEEB0 len 00021150 (132 KiB): DRAM�[0m �[0;32mI (1134) heap_init: At 3FFE0440 len 00003AE0 (14 KiB): D/IRAM�[0m �[0;32mI (1140) heap_init: At 3FFE4350 len 0001BCB0 (111 KiB): D/IRAM�[0m �[0;32mI (1147) heap_init: At 4009E538 len 00001AC8 (6 KiB): IRAM�[0m �[0;32mI (1153) cpu_start: Pro cpu start user code�[0m �[0;32mI (1158) spiram: Adding pool of 4096K of external SPI memory to heap allocator�[0m �[0;32mI (1178) spi_flash: detected chip: generic�[0m �[0;32mI (1178) spi_flash: flash io: qio�[0m �[0;32mI (1178) cpu_start: Starting scheduler on PRO CPU.�[0m �[0;32mI (0) cpu_start: Starting scheduler on APP CPU.�[0m �[0;32mI (1188) SD: Initializing SD card�[0m �[0;32mI (1188) gpio: GPIO[13]| InputEn: 0| OutputEn: 1| OpenDrain: 0| Pullup: 0| Pulldown: 0| Intr:0 �[0m Name: SD64G Type: SDHC/SDXC Speed: 40 MHz Size: 59640MB SPI: display device added to spi bus (1)

SPI: attached display device, speed=8000000

SPI: bus uses native pins: false

SPI: display init...

OK

SPI: Max rd speed = 1000000

SPI: Changed speed to 26666666

�[0;32mI (2688) gpio: GPIO[33]| InputEn: 1| OutputEn: 0| OpenDrain: 0| Pullup: 0| Pulldown: 0| Intr:2 �[0m �[0;32mI (2688) gpio: GPIO[34]| InputEn: 1| OutputEn: 0| OpenDrain: 0| Pullup: 0| Pulldown: 0| Intr:2 �[0m �[0;32mI (2698) gpio: GPIO[35]| InputEn: 1| OutputEn: 0| OpenDrain: 0| Pullup: 0| Pulldown: 0| Intr:2 �[0m �[0;32mI (2708) gpio: GPIO[36]| InputEn: 1| OutputEn: 0| OpenDrain: 0| Pullup: 0| Pulldown: 0| Intr:0 �[0m �[0;32mI (2718) gpio: GPIO[39]| InputEn: 1| OutputEn: 0| OpenDrain: 0| Pullup: 0| Pulldown: 0| Intr:0 �[0m �[0;32mI (2728) AUDIO: Starting audio task�[0m �[0;32mI (2728) I2S: DMA Malloc info, datalen=blocksize=256, dma_buf_count=4�[0m �[0;32mI (2738) I2S: DMA Malloc info, datalen=blocksize=256, dma_buf_count=4�[0m �[0;32mI (2758) I2S: APLL: Req RATE: 44100, real rate: 44099.988, BITS: 32, CLKM: 1, BCK_M: 8, MCLK: 22579194.000, SCLK: 2822399.250000, diva: 1, divb: 0�[0m �[0;31mE (2798) sdmmc_cmd: sdmmc_read_sectors_dma: sdmmc_send_cmd returned 0x109�[0m �[0;31mE (2798) diskio_sdmmc: sdmmc_read_blocks failed (265)�[0m �[0;31mE (2798) FILEIO: Error reading from file�[0m �[0;31mE (2798) PRESET: Root is NULL�[0m �[0;31mE (2808) MENU: Error loading bank from file�[0m �[0;31mE (2808) MENU: Error loading bank�[0m �[0;31mE (2818) sdmmc_cmd: sdmmc_read_sectors_dma: sdmmc_send_cmd returned 0x107�[0m �[0;31mE (2818) diskio_sdmmc: sdmmc_read_blocks failed (263)�[0m �[0;31mE (2828) FILEIO: Could not allocate memory�[0m �[0;31mE (2828) MENU: Error loading tz_shift from config�[0m I (2988) wifi:wifi driver task: 3ffe9e1c, prio:23, stack:6656, core=0 �[0;32mI (2988) system_api: Base MAC address is not set, read default base MAC address from BLK0 of EFUSE�[0m �[0;32mI (2988) system_api: Base MAC address is not set, read default base MAC address from BLK0 of EFUSE�[0m I (3008) wifi:wifi firmware version: 1424aca I (3008) wifi:config NVS flash: enabled I (3008) wifi:config nano formating: disabled I (3008) wifi:Init data frame dynamic rx buffer num: 32 I (3018) wifi:Init management frame dynamic rx buffer num: 32 I (3018) wifi:Init management short buffer num: 32 I (3028) wifi:Init static tx buffer num: 16 I (3028) wifi:Init static rx buffer size: 1600 I (3038) wifi:Init static rx buffer num: 10 I (3038) wifi:Init dynamic rx buffer num: 32 �[0;32mI (3048) wifi_init: rx ba win: 16�[0m �[0;32mI (3048) wifi_init: tcpip mbox: 32�[0m �[0;32mI (3048) wifi_init: udp mbox: 6�[0m �[0;32mI (3058) wifi_init: tcp mbox: 6�[0m �[0;32mI (3058) wifi_init: tcp tx win: 5744�[0m �[0;32mI (3068) wifi_init: tcp rx win: 5744�[0m �[0;32mI (3068) wifi_init: tcp mss: 1440�[0m �[0;32mI (3068) wifi_init: WiFi/LWIP prefer SPIRAM�[0m �[0;32mI (3078) wifi_init: WiFi IRAM OP enabled�[0m �[0;32mI (3078) wifi_init: WiFi RX IRAM OP enabled�[0m �[0;31mE (3088) sdmmc_req: handle_idle_state_events unhandled: 00000008 00000002�[0m �[0;32mI (3098) WIFI: Setting WiFi configuration SSID Fantasy Man�[0m �[0;32mI (3098) phy_init: phy_version 4660,0162888,Dec 23 2020�[0m �[0;33mW (3108) phy_init: failed to load RF calibration data (0x1102), falling back to full calibration�[0m ets Jun 8 2016 00:22:57

rst:0x1 (POWERON_RESET),boot:0x1b (SPI_FAST_FLASH_BOOT) configsip: 0, SPIWP:0⸮⸮半⸮⸮⸮_drv:0x00,q_drv:0x00,d_drv:0x00,c⸮ߤ⸮⸮⸮⸮⸮⸮⸮⸮hd_drv:0x00,wp_drv:0x00 mode:DIO, clock div:2 load:0x3fff0030,len:4 load:0x3fff0034,len:7316 load:0x40078000,len:14252 load:0x40080400,len:4688 entry 0x400806a4 �[0;32mI (28) boot: ESP-IDF v4.1.2-95-gaeb66e1057 2nd stage bootloader�[0m �[0;32mI (28) boot: compile time 09:31:00�[0m �[0;32mI (28) boot: chip revision: 1�[0m �[0;32mI (32) boot_comm: chip revision: 1, min. bootloader chip revision: 0�[0m �[0;32mI (39) qio_mode: Enabling default flash chip QIO�[0m �[0;32mI (44) boot.esp32: SPI Speed : 40MHz�[0m �[0;32mI (49) boot.esp32: SPI Mode : QIO�[0m �[0;32mI (53) boot.esp32: SPI Flash Size : 4MB�[0m �[0;32mI (58) boot: Enabling RNG early entropy source...�[0m �[0;32mI (63) boot: Partition Table:�[0m �[0;32mI (67) boot: ## Label Usage Type ST Offset Length�[0m �[0;32mI (74) boot: 0 nvs WiFi data 01 02 00009000 00006000�[0m �[0;32mI (82) boot: 1 phy_init RF data 01 01 0000f000 00001000�[0m �[0;32mI (89) boot: 2 factory factory app 00 00 00010000 00200000�[0m �[0;32mI (97) boot: End of partition table�[0m �[0;32mI (101) boot_comm: chip revision: 1, min. application chip revision: 0�[0m �[0;32mI (108) esp_image: segment 0: paddr=0x00010020 vaddr=0x3f400020 size=0x2f0f0 (192752) map�[0m �[0;32mI (187) esp_image: segment 1: paddr=0x0003f118 vaddr=0x3ffb0000 size=0x00f00 ( 3840) load�[0m �[0;32mI (189) esp_image: segment 2: paddr=0x00040020 vaddr=0x400d0020 size=0xc7854 (817236) map�[0m �[0;32mI (491) esp_image: segment 3: paddr=0x0010787c vaddr=0x3ffb0f00 size=0x05628 ( 22056) load�[0m �[0;32mI (501) esp_image: segment 4: paddr=0x0010ceac vaddr=0x40080000 size=0x00404 ( 1028) load�[0m �[0;32mI (501) esp_image: segment 5: paddr=0x0010d2b8 vaddr=0x40080404 size=0x1e134 (123188) load�[0m �[0;32mI (579) boot: Loaded app from partition at offset 0x10000�[0m �[0;32mI (579) boot: Disabling RNG early entropy source...�[0m �[0;32mI (580) psram: This chip is ESP32-D0WD�[0m �[0;32mI (584) spiram: Found 64MBit SPI RAM device�[0m �[0;32mI (589) spiram: SPI RAM mode: flash 80m sram 80m�[0m �[0;32mI (594) spiram: PSRAM initialized, cache is in low/high (2-core) mode.�[0m �[0;32mI (601) cpu_start: Pro cpu up.�[0m �[0;32mI (605) cpu_start: Application information:�[0m �[0;32mI (610) cpu_start: Project name: ctag-straempler�[0m �[0;32mI (616) cpu_start: App version: v0.9�[0m �[0;32mI (620) cpu_start: Compile time: Sep 11 2021 09:54:10�[0m �[0;32mI (626) cpu_start: ELF file SHA256: 32bab0cc5eb6c006...�[0m �[0;32mI (632) cpu_start: ESP-IDF: v4.1.2-95-gaeb66e1057�[0m �[0;32mI (638) cpu_start: Starting app cpu, entry point is 0x40081720�[0m �[0;32mI (0) cpu_start: App cpu up.�[0m �[0;32mI (1121) spiram: SPI SRAM memory test OK�[0m �[0;32mI (1121) heap_init: Initializing. RAM available for dynamic allocation:�[0m �[0;32mI (1121) heap_init: At 3FFAE6E0 len 00001920 (6 KiB): DRAM�[0m �[0;32mI (1128) heap_init: At 3FFBEEB0 len 00021150 (132 KiB): DRAM�[0m �[0;32mI (1134) heap_init: At 3FFE0440 len 00003AE0 (14 KiB): D/IRAM�[0m �[0;32mI (1140) heap_init: At 3FFE4350 len 0001BCB0 (111 KiB): D/IRAM�[0m �[0;32mI (1147) heap_init: At 4009E538 len 00001AC8 (6 KiB): IRAM�[0m �[0;32mI (1153) cpu_start: Pro cpu start user code�[0m �[0;32mI (1158) spiram: Adding pool of 4096K of external SPI memory to heap allocator�[0m �[0;32mI (1178) spi_flash: detected chip: generic�[0m �[0;32mI (1178) spi_flash: flash io: qio�[0m �[0;32mI (1178) cpu_start: Starting scheduler on PRO CPU.�[0m �[0;32mI (0) cpu_start: Starting scheduler on APP CPU.�[0m �[0;32mI (1188) SD: Initializing SD card�[0m �[0;32mI (1188) gpio: GPIO[13]| InputEn: 0| OutputEn: 1| OpenDrain: 0| Pullup: 0| Pulldown: 0| Intr:0 �[0m Name: SD64G Type: SDHC/SDXC Speed: 40 MHz Size: 59640MB SPI: display device added to spi bus (1)

SPI: attached display device, speed=8000000

SPI: bus uses native pins: false

SPI: display init...

I guess I should try another SD card ?

Thanks :)

— Reply to this email directly, view it on GitHub https://github.com/ctag-fh-kiel/ctag-straempler/issues/18, or unsubscribe https://github.com/notifications/unsubscribe-auth/ABZMGRR2EKPVCZCPX55UPU3UYBTPFANCNFSM5M4F5HBA . Triage notifications on the go with GitHub Mobile for iOS https://apps.apple.com/app/apple-store/id1477376905?ct=notification-email&mt=8&pt=524675 or Android https://play.google.com/store/apps/details?id=com.github.android&referrer=utm_campaign%3Dnotification-email%26utm_medium%3Demail%26utm_source%3Dgithub.

You are receiving this because you are subscribed to this thread.Message ID: @.***>

polymer81 commented 2 years ago

I will resolder the joints just in case and get another SD card. When I use examples from the SD library I can read / write without problems. When the SD card is removed it also reboots in a loop. I will start with the solder joints.

One other thing I am wondering about, when it boots up and I can edit wifi settings and such, if I would open Slot settings it always triggers a reboot loop. In the monitor it says can´t open Config.json and Default.json - would that cause a reboot ?

Thanks :)

polymer81 commented 2 years ago

I resoldered and measured pins between the SD card and Wrover module - all ok. I still have this reboot loop, both with SD card and without:

ets Jun 8 2016 00:22:57

rst:0x1 (POWERON_RESET),boot:0x1b (SPI_FAST_FLASH_BOOT) configsip: 0, SPIWP:0xee clk_drv:0x00,q_drv:0x00,d_drv:0x00,cs0_drv:0x00,hd_drv:0x00,wp_drv:0x00 mode:DIO, clock div:2 load:0x3fff0030,len:4 load:0x3fff0034,len:7316 load:0x40078000,len:14252 load:0x40080400,len:4688 entry 0x400806a4 I (28) boot: ESP-IDF v4.1.2-95-gaeb66e1057 2nd stage bootloader I (28) boot: compile time 09:31:00 I (28) boot: chip revision: 1 I (32) boot_comm: chip revision: 1, min. bootloader chip revision: 0 I (39) qio_mode: Enabling default flash chip QIO I (45) boot.esp32: SPI Speed : 40MHz I (49) boot.esp32: SPI Mode : QIO I (54) boot.esp32: SPI Flash Size : 4MB I (58) boot: Enabling RNG early entropy source... I (64) boot: Partition Table: I (67) boot: ## Label Usage Type ST Offset Length I (75) boot: 0 nvs WiFi data 01 02 00009000 00006000 I (82) boot: 1 phy_init RF data 01 01 0000f000 00001000 I (90) boot: 2 factory factory app 00 00 00010000 00200000 I (97) boot: End of partition table I (101) boot_comm: chip revision: 1, min. application chip revision: 0 I (108) esp_image: segment 0: paddr=0x00010020 vaddr=0x3f400020 size=0x2f0f0 (192752) map I (188) esp_image: segment 1: paddr=0x0003f118 vaddr=0x3ffb0000 size=0x00f00 ( 3840) load I (190) esp_image: segment 2: paddr=0x00040020 vaddr=0x400d0020 size=0xc7854 (817236) map I (492) esp_image: segment 3: paddr=0x0010787c vaddr=0x3ffb0f00 size=0x05628 ( 22056) load I (501) esp_image: segment 4: paddr=0x0010ceac vaddr=0x40080000 size=0x00404 ( 1028) load I (502) esp_image: segment 5: paddr=0x0010d2b8 vaddr=0x40080404 size=0x1e134 (123188) load I (580) boot: Loaded app from partition at offset 0x10000 I (580) boot: Disabling RNG early entropy source... I (580) psram: This chip is ESP32-D0WD I (585) spiram: Found 64MBit SPI RAM device I (589) spiram: SPI RAM mode: flash 80m sram 80m I (595) spiram: PSRAM initialized, cache is in low/high (2-core) mode. I (602) cpu_start: Pro cpu up. I (606) cpu_start: Application information: I (610) cpu_start: Project name: ctag-straempler I (616) cpu_start: App version: v0.9 I (621) cpu_start: Compile time: Sep 11 2021 09:54:10 I (627) cpu_start: ELF file SHA256: 32bab0cc5eb6c006... I (633) cpu_start: ESP-IDF: v4.1.2-95-gaeb66e1057 I (639) cpu_start: Starting app cpu, entry point is 0x40081720 I (0) cpu_start: App cpu up. I (1121) spiram: SPI SRAM memory test OK I (1122) heap_init: Initializing. RAM available for dynamic allocation: I (1122) heap_init: At 3FFAE6E0 len 00001920 (6 KiB): DRAM I (1128) heap_init: At 3FFBEEB0 len 00021150 (132 KiB): DRAM I (1134) heap_init: At 3FFE0440 len 00003AE0 (14 KiB): D/IRAM I (1141) heap_init: At 3FFE4350 len 0001BCB0 (111 KiB): D/IRAM I (1147) heap_init: At 4009E538 len 00001AC8 (6 KiB): IRAM I (1154) cpu_start: Pro cpu start user code I (1158) spiram: Adding pool of 4096K of external SPI memory to heap allocator I (1179) spi_flash: detected chip: generic I (1179) spi_flash: flash io: qio I (1179) cpu_start: Starting scheduler on PRO CPU. I (0) cpu_start: Starting scheduler on APP CPU. I (1188) SD: Initializing SD card I (1188) gpio: GPIO[13]| InputEn: 0| OutputEn: 1| OpenDrain: 0| Pullup: 0| Pulldown: 0| Intr:0  Name: SS16G Type: SDHC/SDXC Speed: 40 MHz Size: 15193MB SPI: display device added to spi bus (1)

SPI: attached display device, speed=8000000

SPI: bus uses native pins: false

SPI: display init...

OK

SPI: Max rd speed = 1000000

SPI: Changed speed to 26666666

I (6058) gpio: GPIO[33]| InputEn: 1| OutputEn: 0| OpenDrain: 0| Pullup: 0| Pulldown: 0| Intr:2  I (6058) gpio: GPIO[34]| InputEn: 1| OutputEn: 0| OpenDrain: 0| Pullup: 0| Pulldown: 0| Intr:2  I (6058) gpio: GPIO[35]| InputEn: 1| OutputEn: 0| OpenDrain: 0| Pullup: 0| Pulldown: 0| Intr:2  I (6068) gpio: GPIO[36]| InputEn: 1| OutputEn: 0| OpenDrain: 0| Pullup: 0| Pulldown: 0| Intr:0  I (6078) gpio: GPIO[39]| InputEn: 1| OutputEn: 0| OpenDrain: 0| Pullup: 0| Pulldown: 0| Intr:0  I (6088) AUDIO: Starting audio task I (6098) I2S: DMA Malloc info, datalen=blocksize=256, dma_buf_count=4 I (6098) I2S: DMA Malloc info, datalen=blocksize=256, dma_buf_count=4 I (6118) I2S: APLL: Req RATE: 44100, real rate: 44099.988, BITS: 32, CLKM: 1, BCK_M: 8, MCLK: 22579194.000, SCLK: 2822399.250000, diva: 1, divb: 0 E (6238) sdmmc_cmd: sdmmc_read_sectors_dma: sdmmc_send_cmd returned 0xffffffff E (6238) diskio_sdmmc: sdmmc_read_blocks failed (-1) E (6238) sdmmc_req: handle_idle_state_events unhandled: 00000000 00000002 E (6248) sdmmc_req: handle_idle_state_events unhandled: 00000008 00000002 I (6458) wifi:wifi driver task: 3ffe9e1c, prio:23, stack:6656, core=0 I (6458) system_api: Base MAC address is not set, read default base MAC address from BLK0 of EFUSE I (6458) system_api: Base MAC address is not set, read default base MAC address from BLK0 of EFUSE I (6478) wifi:wifi firmware version: 1424aca I (6478) wifi:config NVS flash: enabled I (6478) wifi:config nano formating: disabled I (6478) wifi:Init data frame dynamic rx buffer num: 32 I (6488) wifi:Init management frame dynamic rx buffer num: 32 I (6488) wifi:Init management short buffer num: 32 I (6498) wifi:Init static tx buffer num: 16 I (6498) wifi:Init static rx buffer size: 1600 I (6508) wifi:Init static rx buffer num: 10 I (6508) wifi:Init dynamic rx buffer num: 32 I (6518) wifi_init: rx ba win: 16 I (6518) wifi_init: tcpip mbox: 32 I (6518) wifi_init: udp mbox: 6 I (6528) wifi_init: tcp mbox: 6 I (6528) wifi_init: tcp tx win: 5744 I (6538) wifi_init: tcp rx win: 5744 I (6538) wifi_init: tcp mss: 1440 I (6538) wifi_init: WiFi/LWIP prefer SPIRAM I (6548) wifi_init: WiFi IRAM OP enabled I (6548) wifi_init: WiFi RX IRAM OP enabled I (6558) WIFI: Setting WiFi configuration SSID Fantasy Man I (6558) phy_init: phy_version 4660,0162888,Dec 23 2020 W (6568) phy_init: failed to load RF calibration data (0x1102), falling back to full calibration ets Jun 8 2016 00:22:57

rst:0x1 (POWERON_RESET),boot:0x1b (SPI_FAST_FLASH_BOOT) configsip: 0, SPIWP:0xee clk_drv:0x00,q_drv:0x00,d_drv:0x00,cs0_drv:0x00,hd_drv:0x00,wp_drv:0x00 mode:DIO, clock div:2 load:0x3fff0030,len:4 load:0x3fff0034,len:7316 load:0x40078000,len:14252 load:0x40080400,len:4688 entry 0x400806a4 I (28) boot: ESP-IDF v4.1.2-95-gaeb66e1057 2nd stage bootloader I (28) boot: compile time 09:31:00 I (28) boot: chip revision: 1 I (32) boot_comm: chip revision: 1, min. bootloader chip revision: 0 I (39) qio_mode: Enabling default flash chip QIO I (44) boot.esp32: SPI Speed : 40MHz I (49) boot.esp32: SPI Mode : QIO I (54) boot.esp32: SPI Flash Size : 4MB I (58) boot: Enabling RNG early entropy source... I (64) boot: Partition Table: I (67) boot: ## Label Usage Type ST Offset Length I (74) boot: 0 nvs WiFi data 01 02 00009000 00006000 I (82) boot: 1 phy_init RF data 01 01 0000f000 00001000 I (89) boot: 2 factory factory app 00 00 00010000 00200000 I (97) boot: End of partition table I (101) boot_comm: chip revision: 1, min. application chip revision: 0 I (108) esp_image: segment 0: paddr=0x00010020 vaddr=0x3f400020 size=0x2f0f0 (192752) map I (187) esp_image: segment 1: paddr=0x0003f118 vaddr=0x3ffb0000 size=0x00f00 ( 3840) load I (189) esp_image: segment 2: paddr=0x00040020 vaddr=0x400d0020 size=0xc7854 (817236) map I (492) esp_image: segment 3: paddr=0x0010787c vaddr=0x3ffb0f00 size=0x05628 ( 22056) load I (501) esp_image: segment 4: paddr=0x0010ceac vaddr=0x40080000 size=0x00404 ( 1028) load I (502) esp_image: segment 5: paddr=0x0010d2b8 vaddr=0x40080404 size=0x1e134 (123188) load I (579) boot: Loaded app from partition at offset 0x10000 I (580) boot: Disabling RNG early entropy source... I (580) psram: This chip is ESP32-D0WD I (584) spiram: Found 64MBit SPI RAM device I (589) spiram: SPI RAM mode: flash 80m sram 80m I (594) spiram: PSRAM initialized, cache is in low/high (2-core) mode. I (602) cpu_start: Pro cpu up. I (605) cpu_start: Application information: I (610) cpu_start: Project name: ctag-straempler I (616) cpu_start: App version: v0.9 I (621) cpu_start: Compile time: Sep 11 2021 09:54:10 I (627) cpu_start: ELF file SHA256: 32bab0cc5eb6c006... I (633) cpu_start: ESP-IDF: v4.1.2-95-gaeb66e1057 I (639) cpu_start: Starting app cpu, entry point is 0x40081720 I (0) cpu_start: App cpu up. I (1121) spiram: SPI SRAM memory test OK I (1121) heap_init: Initializing. RAM available for dynamic allocation: I (1122) heap_init: At 3FFAE6E0 len 00001920 (6 KiB): DRAM I (1128) heap_init: At 3FFBEEB0 len 00021150 (132 KiB): DRAM I (1134) heap_init: At 3FFE0440 len 00003AE0 (14 KiB): D/IRAM I (1141) heap_init: At 3FFE4350 len 0001BCB0 (111 KiB): D/IRAM I (1147) heap_init: At 4009E538 len 00001AC8 (6 KiB): IRAM I (1153) cpu_start: Pro cpu start user code I (1158) spiram: Adding pool of 4096K of external SPI memory to heap allocator I (1178) spi_flash: detected chip: generic I (1179) spi_flash: flash io: qio I (1179) cpu_start: Starting scheduler on PRO CPU. I (0) cpu_start: Starting scheduler on APP CPU. I (1188) SD: Initializing SD card I (1188) gpio: GPIO[13]| InputEn: 0| OutputEn: 1| OpenDrain: 0| Pullup: 0| Pulldown: 0| Intr:0  Name: SS16G Type: SDHC/SDXC Speed: 40 MHz Size: 15193MB SPI: display device added to spi bus (1)

SPI: attached display device, speed=8000000

SPI: bus uses native pins: false

SPI: display init...

OK

SPI: Max rd speed = 1000000

SPI: Changed speed to 26666666

I (5918) gpio: GPIO[33]| InputEn: 1| OutputEn: 0| OpenDrain: 0| Pullup: 0| Pulldown: 0| Intr:2  I (5918) gpio: GPIO[34]| InputEn: 1| OutputEn: 0| OpenDrain: 0| Pullup: 0| Pulldown: 0| Intr:2  I (5918) gpio: GPIO[35]| InputEn: 1| OutputEn: 0| OpenDrain: 0| Pullup: 0| Pulldown: 0| Intr:2  I (5928) gpio: GPIO[36]| InputEn: 1| OutputEn: 0| OpenDrain: 0| Pullup: 0| Pulldown: 0| Intr:0  I (5938) gpio: GPIO[39]| InputEn: 1| OutputEn: 0| OpenDrain: 0| Pullup: 0| Pulldown: 0| Intr:0  I (5948) AUDIO: Starting audio task I (5958) I2S: DMA Malloc info, datalen=blocksize=256, dma_buf_count=4 I (5958) I2S: DMA Malloc info, datalen=blocksize=256, dma_buf_count=4 I (5978) I2S: APLL: Req RATE: 44100, real rate: 44099.988, BITS: 32, CLKM: 1, BCK_M: 8, MCLK: 22579194.000, SCLK: 2822399.250000, diva: 1, divb: 0 I (6198) wifi:wifi driver task: 3ffe9e1c, prio:23, stack:6656, core=0 I (6198) system_api: Base MAC address is not set, read default base MAC address from BLK0 of EFUSE I (6198) system_api: Base MAC address is not set, read default base MAC address from BLK0 of EFUSE I (6218) wifi:wifi firmware version: 1424aca I (6218) wifi:config NVS flash: enabled I (6218) wifi:config nano formating: disabled I (6218) wifi:Init data frame dynamic rx buffer num: 32 I (6228) wifi:Init management frame dynamic rx buffer num: 32 I (6228) wifi:Init management short buffer num: 32 I (6238) wifi:Init static tx buffer num: 16 I (6238) wifi:Init static rx buffer size: 1600 I (6248) wifi:Init static rx buffer num: 10 I (6248) wifi:Init dynamic rx buffer num: 32 I (6258) wifi_init: rx ba win: 16 I (6258) wifi_init: tcpip mbox: 32 I (6258) wifi_init: udp mbox: 6 I (6268) wifi_init: tcp mbox: 6 I (6268) wifi_init: tcp tx win: 5744 I (6278) wifi_init: tcp rx win: 5744 I (6278) wifi_init: tcp mss: 1440 I (6278) wifi_init: WiFi/LWIP prefer SPIRAM I (6288) wifi_init: WiFi IRAM OP enabled I (6288) wifi_init: WiFi RX IRAM OP enabled I (6298) WIFI: Setting WiFi configuration SSID Fantasy Man I (6298) phy_init: phy_version 4660,0162888,Dec 23 2020 W (6308) phy_init: failed to load RF calibration data (0x1102), falling back to full calibration ets Jun 8 2016 00:22:57

ctag-fh-kiel commented 2 years ago

Check your power supply, possibly the MIC power supervisory issues a reset upon power draw, when wifi is enabled. You can try to remove the MIC chip...

On Thu, Jan 27, 2022 at 10:57 AM polymer81 @.***> wrote:

I resoldered and measured pins between the SD card and Wrover module - all ok. I still have this reboot loop, both with SD card and without:

ets Jun 8 2016 00:22:57

rst:0x1 (POWERON_RESET),boot:0x1b (SPI_FAST_FLASH_BOOT) configsip: 0, SPIWP:0xee clk_drv:0x00,q_drv:0x00,d_drv:0x00,cs0_drv:0x00,hd_drv:0x00,wp_drv:0x00 mode:DIO, clock div:2 load:0x3fff0030,len:4 load:0x3fff0034,len:7316 load:0x40078000,len:14252 load:0x40080400,len:4688 entry 0x400806a4 �[0;32mI (28) boot: ESP-IDF v4.1.2-95-gaeb66e1057 2nd stage bootloader�[0m �[0;32mI (28) boot: compile time 09:31:00�[0m �[0;32mI (28) boot: chip revision: 1�[0m �[0;32mI (32) boot_comm: chip revision: 1, min. bootloader chip revision: 0�[0m �[0;32mI (39) qio_mode: Enabling default flash chip QIO�[0m �[0;32mI (45) boot.esp32: SPI Speed : 40MHz�[0m �[0;32mI (49) boot.esp32: SPI Mode : QIO�[0m �[0;32mI (54) boot.esp32: SPI Flash Size : 4MB�[0m �[0;32mI (58) boot: Enabling RNG early entropy source...�[0m �[0;32mI (64) boot: Partition Table:�[0m �[0;32mI (67) boot: ## Label Usage Type ST Offset Length�[0m �[0;32mI (75) boot: 0 nvs WiFi data 01 02 00009000 00006000�[0m �[0;32mI (82) boot: 1 phy_init RF data 01 01 0000f000 00001000�[0m �[0;32mI (90) boot: 2 factory factory app 00 00 00010000 00200000�[0m �[0;32mI (97) boot: End of partition table�[0m �[0;32mI (101) boot_comm: chip revision: 1, min. application chip revision: 0�[0m �[0;32mI (108) esp_image: segment 0: paddr=0x00010020 vaddr=0x3f400020 size=0x2f0f0 (192752) map�[0m �[0;32mI (188) esp_image: segment 1: paddr=0x0003f118 vaddr=0x3ffb0000 size=0x00f00 ( 3840) load�[0m �[0;32mI (190) esp_image: segment 2: paddr=0x00040020 vaddr=0x400d0020 size=0xc7854 (817236) map�[0m �[0;32mI (492) esp_image: segment 3: paddr=0x0010787c vaddr=0x3ffb0f00 size=0x05628 ( 22056) load�[0m �[0;32mI (501) esp_image: segment 4: paddr=0x0010ceac vaddr=0x40080000 size=0x00404 ( 1028) load�[0m �[0;32mI (502) esp_image: segment 5: paddr=0x0010d2b8 vaddr=0x40080404 size=0x1e134 (123188) load�[0m �[0;32mI (580) boot: Loaded app from partition at offset 0x10000�[0m �[0;32mI (580) boot: Disabling RNG early entropy source...�[0m �[0;32mI (580) psram: This chip is ESP32-D0WD�[0m �[0;32mI (585) spiram: Found 64MBit SPI RAM device�[0m �[0;32mI (589) spiram: SPI RAM mode: flash 80m sram 80m�[0m �[0;32mI (595) spiram: PSRAM initialized, cache is in low/high (2-core) mode.�[0m �[0;32mI (602) cpu_start: Pro cpu up.�[0m �[0;32mI (606) cpu_start: Application information:�[0m �[0;32mI (610) cpu_start: Project name: ctag-straempler�[0m �[0;32mI (616) cpu_start: App version: v0.9�[0m �[0;32mI (621) cpu_start: Compile time: Sep 11 2021 09:54:10�[0m �[0;32mI (627) cpu_start: ELF file SHA256: 32bab0cc5eb6c006...�[0m �[0;32mI (633) cpu_start: ESP-IDF: v4.1.2-95-gaeb66e1057�[0m �[0;32mI (639) cpu_start: Starting app cpu, entry point is 0x40081720�[0m �[0;32mI (0) cpu_start: App cpu up.�[0m �[0;32mI (1121) spiram: SPI SRAM memory test OK�[0m �[0;32mI (1122) heap_init: Initializing. RAM available for dynamic allocation:�[0m �[0;32mI (1122) heap_init: At 3FFAE6E0 len 00001920 (6 KiB): DRAM�[0m �[0;32mI (1128) heap_init: At 3FFBEEB0 len 00021150 (132 KiB): DRAM�[0m �[0;32mI (1134) heap_init: At 3FFE0440 len 00003AE0 (14 KiB): D/IRAM�[0m �[0;32mI (1141) heap_init: At 3FFE4350 len 0001BCB0 (111 KiB): D/IRAM�[0m �[0;32mI (1147) heap_init: At 4009E538 len 00001AC8 (6 KiB): IRAM�[0m �[0;32mI (1154) cpu_start: Pro cpu start user code�[0m �[0;32mI (1158) spiram: Adding pool of 4096K of external SPI memory to heap allocator�[0m �[0;32mI (1179) spi_flash: detected chip: generic�[0m �[0;32mI (1179) spi_flash: flash io: qio�[0m �[0;32mI (1179) cpu_start: Starting scheduler on PRO CPU.�[0m �[0;32mI (0) cpu_start: Starting scheduler on APP CPU.�[0m �[0;32mI (1188) SD: Initializing SD card�[0m �[0;32mI (1188) gpio: GPIO[13]| InputEn: 0| OutputEn: 1| OpenDrain: 0| Pullup: 0| Pulldown: 0| Intr:0 �[0m Name: SS16G Type: SDHC/SDXC Speed: 40 MHz Size: 15193MB SPI: display device added to spi bus (1)

SPI: attached display device, speed=8000000

SPI: bus uses native pins: false

SPI: display init...

OK

SPI: Max rd speed = 1000000

SPI: Changed speed to 26666666

�[0;32mI (6058) gpio: GPIO[33]| InputEn: 1| OutputEn: 0| OpenDrain: 0| Pullup: 0| Pulldown: 0| Intr:2 �[0m �[0;32mI (6058) gpio: GPIO[34]| InputEn: 1| OutputEn: 0| OpenDrain: 0| Pullup: 0| Pulldown: 0| Intr:2 �[0m �[0;32mI (6058) gpio: GPIO[35]| InputEn: 1| OutputEn: 0| OpenDrain: 0| Pullup: 0| Pulldown: 0| Intr:2 �[0m �[0;32mI (6068) gpio: GPIO[36]| InputEn: 1| OutputEn: 0| OpenDrain: 0| Pullup: 0| Pulldown: 0| Intr:0 �[0m �[0;32mI (6078) gpio: GPIO[39]| InputEn: 1| OutputEn: 0| OpenDrain: 0| Pullup: 0| Pulldown: 0| Intr:0 �[0m �[0;32mI (6088) AUDIO: Starting audio task�[0m �[0;32mI (6098) I2S: DMA Malloc info, datalen=blocksize=256, dma_buf_count=4�[0m �[0;32mI (6098) I2S: DMA Malloc info, datalen=blocksize=256, dma_buf_count=4�[0m �[0;32mI (6118) I2S: APLL: Req RATE: 44100, real rate: 44099.988, BITS: 32, CLKM: 1, BCK_M: 8, MCLK: 22579194.000, SCLK: 2822399.250000, diva: 1, divb: 0�[0m �[0;31mE (6238) sdmmc_cmd: sdmmc_read_sectors_dma: sdmmc_send_cmd returned 0xffffffff�[0m �[0;31mE (6238) diskio_sdmmc: sdmmc_read_blocks failed (-1)�[0m �[0;31mE (6238) sdmmc_req: handle_idle_state_events unhandled: 00000000 00000002�[0m �[0;31mE (6248) sdmmc_req: handle_idle_state_events unhandled: 00000008 00000002�[0m I (6458) wifi:wifi driver task: 3ffe9e1c, prio:23, stack:6656, core=0 �[0;32mI (6458) system_api: Base MAC address is not set, read default base MAC address from BLK0 of EFUSE�[0m �[0;32mI (6458) system_api: Base MAC address is not set, read default base MAC address from BLK0 of EFUSE�[0m I (6478) wifi:wifi firmware version: 1424aca I (6478) wifi:config NVS flash: enabled I (6478) wifi:config nano formating: disabled I (6478) wifi:Init data frame dynamic rx buffer num: 32 I (6488) wifi:Init management frame dynamic rx buffer num: 32 I (6488) wifi:Init management short buffer num: 32 I (6498) wifi:Init static tx buffer num: 16 I (6498) wifi:Init static rx buffer size: 1600 I (6508) wifi:Init static rx buffer num: 10 I (6508) wifi:Init dynamic rx buffer num: 32 �[0;32mI (6518) wifi_init: rx ba win: 16�[0m �[0;32mI (6518) wifi_init: tcpip mbox: 32�[0m �[0;32mI (6518) wifi_init: udp mbox: 6�[0m �[0;32mI (6528) wifi_init: tcp mbox: 6�[0m �[0;32mI (6528) wifi_init: tcp tx win: 5744�[0m �[0;32mI (6538) wifi_init: tcp rx win: 5744�[0m �[0;32mI (6538) wifi_init: tcp mss: 1440�[0m �[0;32mI (6538) wifi_init: WiFi/LWIP prefer SPIRAM�[0m �[0;32mI (6548) wifi_init: WiFi IRAM OP enabled�[0m �[0;32mI (6548) wifi_init: WiFi RX IRAM OP enabled�[0m �[0;32mI (6558) WIFI: Setting WiFi configuration SSID Fantasy Man�[0m �[0;32mI (6558) phy_init: phy_version 4660,0162888,Dec 23 2020�[0m �[0;33mW (6568) phy_init: failed to load RF calibration data (0x1102), falling back to full calibration�[0m ets Jun 8 2016 00:22:57

rst:0x1 (POWERON_RESET),boot:0x1b (SPI_FAST_FLASH_BOOT) configsip: 0, SPIWP:0xee clk_drv:0x00,q_drv:0x00,d_drv:0x00,cs0_drv:0x00,hd_drv:0x00,wp_drv:0x00 mode:DIO, clock div:2 load:0x3fff0030,len:4 load:0x3fff0034,len:7316 load:0x40078000,len:14252 load:0x40080400,len:4688 entry 0x400806a4 �[0;32mI (28) boot: ESP-IDF v4.1.2-95-gaeb66e1057 2nd stage bootloader�[0m �[0;32mI (28) boot: compile time 09:31:00�[0m �[0;32mI (28) boot: chip revision: 1�[0m �[0;32mI (32) boot_comm: chip revision: 1, min. bootloader chip revision: 0�[0m �[0;32mI (39) qio_mode: Enabling default flash chip QIO�[0m �[0;32mI (44) boot.esp32: SPI Speed : 40MHz�[0m �[0;32mI (49) boot.esp32: SPI Mode : QIO�[0m �[0;32mI (54) boot.esp32: SPI Flash Size : 4MB�[0m �[0;32mI (58) boot: Enabling RNG early entropy source...�[0m �[0;32mI (64) boot: Partition Table:�[0m �[0;32mI (67) boot: ## Label Usage Type ST Offset Length�[0m �[0;32mI (74) boot: 0 nvs WiFi data 01 02 00009000 00006000�[0m �[0;32mI (82) boot: 1 phy_init RF data 01 01 0000f000 00001000�[0m �[0;32mI (89) boot: 2 factory factory app 00 00 00010000 00200000�[0m �[0;32mI (97) boot: End of partition table�[0m �[0;32mI (101) boot_comm: chip revision: 1, min. application chip revision: 0�[0m �[0;32mI (108) esp_image: segment 0: paddr=0x00010020 vaddr=0x3f400020 size=0x2f0f0 (192752) map�[0m �[0;32mI (187) esp_image: segment 1: paddr=0x0003f118 vaddr=0x3ffb0000 size=0x00f00 ( 3840) load�[0m �[0;32mI (189) esp_image: segment 2: paddr=0x00040020 vaddr=0x400d0020 size=0xc7854 (817236) map�[0m �[0;32mI (492) esp_image: segment 3: paddr=0x0010787c vaddr=0x3ffb0f00 size=0x05628 ( 22056) load�[0m �[0;32mI (501) esp_image: segment 4: paddr=0x0010ceac vaddr=0x40080000 size=0x00404 ( 1028) load�[0m �[0;32mI (502) esp_image: segment 5: paddr=0x0010d2b8 vaddr=0x40080404 size=0x1e134 (123188) load�[0m �[0;32mI (579) boot: Loaded app from partition at offset 0x10000�[0m �[0;32mI (580) boot: Disabling RNG early entropy source...�[0m �[0;32mI (580) psram: This chip is ESP32-D0WD�[0m �[0;32mI (584) spiram: Found 64MBit SPI RAM device�[0m �[0;32mI (589) spiram: SPI RAM mode: flash 80m sram 80m�[0m �[0;32mI (594) spiram: PSRAM initialized, cache is in low/high (2-core) mode.�[0m �[0;32mI (602) cpu_start: Pro cpu up.�[0m �[0;32mI (605) cpu_start: Application information:�[0m �[0;32mI (610) cpu_start: Project name: ctag-straempler�[0m �[0;32mI (616) cpu_start: App version: v0.9�[0m �[0;32mI (621) cpu_start: Compile time: Sep 11 2021 09:54:10�[0m �[0;32mI (627) cpu_start: ELF file SHA256: 32bab0cc5eb6c006...�[0m �[0;32mI (633) cpu_start: ESP-IDF: v4.1.2-95-gaeb66e1057�[0m �[0;32mI (639) cpu_start: Starting app cpu, entry point is 0x40081720�[0m �[0;32mI (0) cpu_start: App cpu up.�[0m �[0;32mI (1121) spiram: SPI SRAM memory test OK�[0m �[0;32mI (1121) heap_init: Initializing. RAM available for dynamic allocation:�[0m �[0;32mI (1122) heap_init: At 3FFAE6E0 len 00001920 (6 KiB): DRAM�[0m �[0;32mI (1128) heap_init: At 3FFBEEB0 len 00021150 (132 KiB): DRAM�[0m �[0;32mI (1134) heap_init: At 3FFE0440 len 00003AE0 (14 KiB): D/IRAM�[0m �[0;32mI (1141) heap_init: At 3FFE4350 len 0001BCB0 (111 KiB): D/IRAM�[0m �[0;32mI (1147) heap_init: At 4009E538 len 00001AC8 (6 KiB): IRAM�[0m �[0;32mI (1153) cpu_start: Pro cpu start user code�[0m �[0;32mI (1158) spiram: Adding pool of 4096K of external SPI memory to heap allocator�[0m �[0;32mI (1178) spi_flash: detected chip: generic�[0m �[0;32mI (1179) spi_flash: flash io: qio�[0m �[0;32mI (1179) cpu_start: Starting scheduler on PRO CPU.�[0m �[0;32mI (0) cpu_start: Starting scheduler on APP CPU.�[0m �[0;32mI (1188) SD: Initializing SD card�[0m �[0;32mI (1188) gpio: GPIO[13]| InputEn: 0| OutputEn: 1| OpenDrain: 0| Pullup: 0| Pulldown: 0| Intr:0 �[0m Name: SS16G Type: SDHC/SDXC Speed: 40 MHz Size: 15193MB SPI: display device added to spi bus (1)

SPI: attached display device, speed=8000000

SPI: bus uses native pins: false

SPI: display init...

OK

SPI: Max rd speed = 1000000

SPI: Changed speed to 26666666

�[0;32mI (5918) gpio: GPIO[33]| InputEn: 1| OutputEn: 0| OpenDrain: 0| Pullup: 0| Pulldown: 0| Intr:2 �[0m �[0;32mI (5918) gpio: GPIO[34]| InputEn: 1| OutputEn: 0| OpenDrain: 0| Pullup: 0| Pulldown: 0| Intr:2 �[0m �[0;32mI (5918) gpio: GPIO[35]| InputEn: 1| OutputEn: 0| OpenDrain: 0| Pullup: 0| Pulldown: 0| Intr:2 �[0m �[0;32mI (5928) gpio: GPIO[36]| InputEn: 1| OutputEn: 0| OpenDrain: 0| Pullup: 0| Pulldown: 0| Intr:0 �[0m �[0;32mI (5938) gpio: GPIO[39]| InputEn: 1| OutputEn: 0| OpenDrain: 0| Pullup: 0| Pulldown: 0| Intr:0 �[0m �[0;32mI (5948) AUDIO: Starting audio task�[0m �[0;32mI (5958) I2S: DMA Malloc info, datalen=blocksize=256, dma_buf_count=4�[0m �[0;32mI (5958) I2S: DMA Malloc info, datalen=blocksize=256, dma_buf_count=4�[0m �[0;32mI (5978) I2S: APLL: Req RATE: 44100, real rate: 44099.988, BITS: 32, CLKM: 1, BCK_M: 8, MCLK: 22579194.000, SCLK: 2822399.250000, diva: 1, divb: 0�[0m I (6198) wifi:wifi driver task: 3ffe9e1c, prio:23, stack:6656, core=0 �[0;32mI (6198) system_api: Base MAC address is not set, read default base MAC address from BLK0 of EFUSE�[0m �[0;32mI (6198) system_api: Base MAC address is not set, read default base MAC address from BLK0 of EFUSE�[0m I (6218) wifi:wifi firmware version: 1424aca I (6218) wifi:config NVS flash: enabled I (6218) wifi:config nano formating: disabled I (6218) wifi:Init data frame dynamic rx buffer num: 32 I (6228) wifi:Init management frame dynamic rx buffer num: 32 I (6228) wifi:Init management short buffer num: 32 I (6238) wifi:Init static tx buffer num: 16 I (6238) wifi:Init static rx buffer size: 1600 I (6248) wifi:Init static rx buffer num: 10 I (6248) wifi:Init dynamic rx buffer num: 32 �[0;32mI (6258) wifi_init: rx ba win: 16�[0m �[0;32mI (6258) wifi_init: tcpip mbox: 32�[0m �[0;32mI (6258) wifi_init: udp mbox: 6�[0m �[0;32mI (6268) wifi_init: tcp mbox: 6�[0m �[0;32mI (6268) wifi_init: tcp tx win: 5744�[0m �[0;32mI (6278) wifi_init: tcp rx win: 5744�[0m �[0;32mI (6278) wifi_init: tcp mss: 1440�[0m �[0;32mI (6278) wifi_init: WiFi/LWIP prefer SPIRAM�[0m �[0;32mI (6288) wifi_init: WiFi IRAM OP enabled�[0m �[0;32mI (6288) wifi_init: WiFi RX IRAM OP enabled�[0m �[0;32mI (6298) WIFI: Setting WiFi configuration SSID Fantasy Man�[0m �[0;32mI (6298) phy_init: phy_version 4660,0162888,Dec 23 2020�[0m �[0;33mW (6308) phy_init: failed to load RF calibration data (0x1102), falling back to full calibration�[0m ets Jun 8 2016 00:22:57

— Reply to this email directly, view it on GitHub https://github.com/ctag-fh-kiel/ctag-straempler/issues/18#issuecomment-1023035839, or unsubscribe https://github.com/notifications/unsubscribe-auth/ABZMGRUNX6DYAO7FAUO5FKTUYEJIZANCNFSM5M4F5HBA . Triage notifications on the go with GitHub Mobile for iOS https://apps.apple.com/app/apple-store/id1477376905?ct=notification-email&mt=8&pt=524675 or Android https://play.google.com/store/apps/details?id=com.github.android&referrer=utm_campaign%3Dnotification-email%26utm_medium%3Demail%26utm_source%3Dgithub.

You are receiving this because you commented.Message ID: @.***>

polymer81 commented 2 years ago

I will try that, thanks !

polymer81 commented 2 years ago

The rebooting is fixed by removing the MIC803 chip, thanks :)

I can load samples to it through the browser, but it seems to overwrite config.json file with a blank one and if I open Slot menu it resets with this :

E (65919) FILEIO: Could not open file /sdcard/CONFIG.JSN for reading Guru Meditation Error: Core 0 panic'ed (LoadProhibited). Exception was unhandled. Core 0 register dump: PC : 0x400dfba2 PS : 0x00060930 A0 : 0x800d9e51 A1 : 0x3ffd6e30
A2 : 0x00000001 A3 : 0x00000040 A4 : 0x3ffb6f08 A5 : 0x00000000
A6 : 0x00000001 A7 : 0x00000000 A8 : 0x800dfb9e A9 : 0x3ffd6e10
A10 : 0x00000000 A11 : 0x00000040 A12 : 0x3f40799c A13 : 0x00000001
A14 : 0x3f407bc0 A15 : 0x3ffd6e00 SAR : 0x0000001b EXCCAUSE: 0x0000001c
EXCVADDR: 0x00000010 LBEG : 0x4008c8c1 LEND : 0x4008c8d1 LCOUNT : 0xffffffff

ELF file SHA256: 32bab0cc5eb6c006

Backtrace: 0x400dfb9f:0x3ffd6e30 0x400d9e4e:0x3ffd6ea0 0x401934e2:0x3ffd6ec0 0x400d9ecf:0x3ffd6ee0 0x400d7527:0x3ffd6f00

Rebooting... ets Jun 8 2016 00:22:57

rst:0xc (SW_CPU_RESET),boot:0x1b (SPI_FAST_FLASH_BOOT) configsip: 0, SPIWP:0xee clk_drv:0x00,q_drv:0x00,d_drv:0x00,cs0_drv:0x00,hd_drv:0x00,wp_drv:0x00 mode:DIO, clock div:1 load:0x3fff0030,len:4 load:0x3fff0034,len:7316 load:0x40078000,len:14252 load:0x40080400,len:4688 entry 0x400806a4 I (29) boot: ESP-IDF v4.1.2-95-gaeb66e1057 2nd stage bootloader I (29) boot: compile time 09:31:00 I (29) boot: chip revision: 1 I (33) boot_comm: chip revision: 1, min. bootloader chip revision: 0 I (40) qio_mode: Enabling default flash chip QIO I (46) boot.esp32: SPI Speed : 80MHz I (50) boot.esp32: SPI Mode : QIO I (55) boot.esp32: SPI Flash Size : 4MB I (59) boot: Enabling RNG early entropy source... I (65) boot: Partition Table: I (68) boot: ## Label Usage Type ST Offset Length I (76) boot: 0 nvs WiFi data 01 02 00009000 00006000 I (83) boot: 1 phy_init RF data 01 01 0000f000 00001000 I (90) boot: 2 factory factory app 00 00 00010000 00200000 I (98) boot: End of partition table I (102) boot_comm: chip revision: 1, min. application chip revision: 0 I (109) esp_image: segment 0: paddr=0x00010020 vaddr=0x3f400020 size=0x2f0f0 (192752) map I (182) esp_image: segment 1: paddr=0x0003f118 vaddr=0x3ffb0000 size=0x00f00 ( 3840) load I (184) esp_image: segment 2: paddr=0x00040020 vaddr=0x400d0020 size=0xc7854 (817236) map I (459) esp_image: segment 3: paddr=0x0010787c vaddr=0x3ffb0f00 size=0x05628 ( 22056) load I (468) esp_image: segment 4: paddr=0x0010ceac vaddr=0x40080000 size=0x00404 ( 1028) load I (468) esp_image: segment 5: paddr=0x0010d2b8 vaddr=0x40080404 size=0x1e134 (123188) load I (541) boot: Loaded app from partition at offset 0x10000 I (541) boot: Disabling RNG early entropy source... I (541) psram: This chip is ESP32-D0WD I (546) spiram: Found 64MBit SPI RAM device I (550) spiram: SPI RAM mode: flash 80m sram 80m I (556) spiram: PSRAM initialized, cache is in low/high (2-core) mode. I (563) cpu_start: Pro cpu up. I (567) cpu_start: Application information: I (571) cpu_start: Project name: ctag-straempler I (577) cpu_start: App version: v0.9 I (582) cpu_start: Compile time: Sep 11 2021 09:54:10 I (588) cpu_start: ELF file SHA256: 32bab0cc5eb6c006... I (594) cpu_start: ESP-IDF: v4.1.2-95-gaeb66e1057 I (600) cpu_start: Starting app cpu, entry point is 0x40081720 I (592) cpu_start: App cpu up. I (1082) spiram: SPI SRAM memory test OK I (1083) heap_init: Initializing. RAM available for dynamic allocation: I (1083) heap_init: At 3FFAE6E0 len 00001920 (6 KiB): DRAM I (1089) heap_init: At 3FFBEEB0 len 00021150 (132 KiB): DRAM I (1096) heap_init: At 3FFE0440 len 00003AE0 (14 KiB): D/IRAM I (1102) heap_init: At 3FFE4350 len 0001BCB0 (111 KiB): D/IRAM I (1109) heap_init: At 4009E538 len 00001AC8 (6 KiB): IRAM I (1115) cpu_start: Pro cpu start user code I (1120) spiram: Adding pool of 4096K of external SPI memory to heap allocator I (1140) spi_flash: detected chip: generic I (1140) spi_flash: flash io: qio I (1140) cpu_start: Starting scheduler on PRO CPU. I (0) cpu_start: Starting scheduler on APP CPU. I (1149) SD: Initializing SD card I (1149) gpio: GPIO[13]| InputEn: 0| OutputEn: 1| OpenDrain: 0| Pullup: 0| Pulldown: 0| Intr:0  E (1219) sdmmc_sd: sdmmc_send_cmd_switch_func: sdmmc_send_cmd returned 0x109 E (1219) SD: Failed to initialize the card (265). Make sure SD card lines have pull-up resistors in place. SPI: display device added to spi bus (1)

SPI: attached display device, speed=8000000

SPI: bus uses native pins: false

SPI: display init...

OK

SPI: Max rd speed = 1000000

SPI: Changed speed to 26666666

I (2679) gpio: GPIO[33]| InputEn: 1| OutputEn: 0| OpenDrain: 0| Pullup: 0| Pulldown: 0| Intr:2  I (2679) gpio: GPIO[34]| InputEn: 1| OutputEn: 0| OpenDrain: 0| Pullup: 0| Pulldown: 0| Intr:2  I (2689) gpio: GPIO[35]| InputEn: 1| OutputEn: 0| OpenDrain: 0| Pullup: 0| Pulldown: 0| Intr:2  I (2699) gpio: GPIO[36]| InputEn: 1| OutputEn: 0| OpenDrain: 0| Pullup: 0| Pulldown: 0| Intr:0  I (2709) gpio: GPIO[39]| InputEn: 1| OutputEn: 0| OpenDrain: 0| Pullup: 0| Pulldown: 0| Intr:0  I (2719) AUDIO: Starting audio task I (2719) I2S: DMA Malloc info, datalen=blocksize=256, dma_buf_count=4 I (2729) I2S: DMA Malloc info, datalen=blocksize=256, dma_buf_count=4 I (2749) I2S: APLL: Req RATE: 44100, real rate: 44099.988, BITS: 32, CLKM: 1, BCK_M: 8, MCLK: 22579194.000, SCLK: 2822399.250000, diva: 1, divb: 0 E (2759) FILEIO: Could not open file /sdcard/CONFIG.JSN for reading E (2759) AUDIO: Couldn't open config.jsn E (2769) FILEIO: Could not open file /sdcard/CONFIG.JSN for reading E (2769) FILEIO: Could not open file /sdcard/banks/DEFAULT.JSN for reading E (2779) PRESET: Root is NULL E (2789) MENU: Error loading bank from file E (2789) MENU: Error loading bank E (2789) FILEIO: Could not open file /sdcard/CONFIG.JSN for reading E (2799) MENU: Error loading tz_shift from config I (2959) wifi:wifi driver task: 3ffdd804, prio:23, stack:6656, core=0 I (2959) system_api: Base MAC address is not set, read default base MAC address from BLK0 of EFUSE I (2959) system_api: Base MAC address is not set, read default base MAC address from BLK0 of EFUSE I (2979) wifi:wifi firmware version: 1424aca I (2979) wifi:config NVS flash: enabled I (2979) wifi:config nano formating: disabled I (2979) wifi:Init data frame dynamic rx buffer num: 32 I (2989) wifi:Init management frame dynamic rx buffer num: 32 I (2989) wifi:Init management short buffer num: 32 I (2999) wifi:Init static tx buffer num: 16 I (2999) wifi:Init static rx buffer size: 1600 I (3009) wifi:Init static rx buffer num: 10 I (3009) wifi:Init dynamic rx buffer num: 32 I (3019) wifi_init: rx ba win: 16 I (3019) wifi_init: tcpip mbox: 32 I (3019) wifi_init: udp mbox: 6 I (3029) wifi_init: tcp mbox: 6 I (3029) wifi_init: tcp tx win: 5744 I (3039) wifi_init: tcp rx win: 5744 I (3039) wifi_init: tcp mss: 1440 I (3039) wifi_init: WiFi/LWIP prefer SPIRAM I (3049) wifi_init: WiFi IRAM OP enabled I (3049) wifi_init: WiFi RX IRAM OP enabled E (3059) FILEIO: Could not open file /sdcard/CONFIG.JSN for reading E (3059) FILEIO: root == NULL I (3069) WIFI: Setting WiFi configuration SSID ⸮? I (3069) phy_init: phy_version 4660,0162888,Dec 23 2020 I (3159) wifi:mode : sta (b8:f0:09:80:a9:d8)

Is there anything else that should be on SD card (heard about an excel file but could not find) - this is what I have

Folders

BANKS, POOl, RAW, USR

Files

Config.json and Silence.RAW

polymer81 commented 2 years ago

The SD card holder I have is missing one pin - pin1 / DAT2, that is not used in the code or in the schematic. Could that cause any problems ?

ctag-fh-kiel commented 2 years ago

All files/folders are automatically created when you boot Strämpler with a freshly FAT32 formatted SD card. Remove the card only when the module is powered off, otherwise the card can be damaged. You can copy a bootlogo to the root, e.g. this one https://github.com/ctag-fh-kiel/ctag-straempler/blob/master/bootlogo/bootlogo.bmp but it is not required. You can edit the config.jsn on your PC if you want, entering freesound account data (remember remove/insert sd card only when module powered off)...

On Thu, Jan 27, 2022 at 3:49 PM polymer81 @.***> wrote:

The rebooting is fixed by removing the MIC803 chip, thanks :)

I can load samples to it through the browser, but it seems to overwrite config.json file with a blank one and if I open Slot menu it resets with this :

�[0;31mE (65919) FILEIO: Could not open file /sdcard/CONFIG.JSN for reading�[0m Guru Meditation Error: Core 0 panic'ed (LoadProhibited). Exception was unhandled. Core 0 register dump: PC : 0x400dfba2 PS : 0x00060930 A0 : 0x800d9e51 A1 : 0x3ffd6e30 A2 : 0x00000001 A3 : 0x00000040 A4 : 0x3ffb6f08 A5 : 0x00000000 A6 : 0x00000001 A7 : 0x00000000 A8 : 0x800dfb9e A9 : 0x3ffd6e10 A10 : 0x00000000 A11 : 0x00000040 A12 : 0x3f40799c A13 : 0x00000001 A14 : 0x3f407bc0 A15 : 0x3ffd6e00 SAR : 0x0000001b EXCCAUSE: 0x0000001c EXCVADDR: 0x00000010 LBEG : 0x4008c8c1 LEND : 0x4008c8d1 LCOUNT : 0xffffffff

ELF file SHA256: 32bab0cc5eb6c006

Backtrace: 0x400dfb9f:0x3ffd6e30 0x400d9e4e:0x3ffd6ea0 0x401934e2:0x3ffd6ec0 0x400d9ecf:0x3ffd6ee0 0x400d7527:0x3ffd6f00

Rebooting... ets Jun 8 2016 00:22:57

rst:0xc (SW_CPU_RESET),boot:0x1b (SPI_FAST_FLASH_BOOT) configsip: 0, SPIWP:0xee clk_drv:0x00,q_drv:0x00,d_drv:0x00,cs0_drv:0x00,hd_drv:0x00,wp_drv:0x00 mode:DIO, clock div:1 load:0x3fff0030,len:4 load:0x3fff0034,len:7316 load:0x40078000,len:14252 load:0x40080400,len:4688 entry 0x400806a4 �[0;32mI (29) boot: ESP-IDF v4.1.2-95-gaeb66e1057 2nd stage bootloader�[0m �[0;32mI (29) boot: compile time 09:31:00�[0m �[0;32mI (29) boot: chip revision: 1�[0m �[0;32mI (33) boot_comm: chip revision: 1, min. bootloader chip revision: 0�[0m �[0;32mI (40) qio_mode: Enabling default flash chip QIO�[0m �[0;32mI (46) boot.esp32: SPI Speed : 80MHz�[0m �[0;32mI (50) boot.esp32: SPI Mode : QIO�[0m �[0;32mI (55) boot.esp32: SPI Flash Size : 4MB�[0m �[0;32mI (59) boot: Enabling RNG early entropy source...�[0m �[0;32mI (65) boot: Partition Table:�[0m �[0;32mI (68) boot: ## Label Usage Type ST Offset Length�[0m �[0;32mI (76) boot: 0 nvs WiFi data 01 02 00009000 00006000�[0m �[0;32mI (83) boot: 1 phy_init RF data 01 01 0000f000 00001000�[0m �[0;32mI (90) boot: 2 factory factory app 00 00 00010000 00200000�[0m �[0;32mI (98) boot: End of partition table�[0m �[0;32mI (102) boot_comm: chip revision: 1, min. application chip revision: 0�[0m �[0;32mI (109) esp_image: segment 0: paddr=0x00010020 vaddr=0x3f400020 size=0x2f0f0 (192752) map�[0m �[0;32mI (182) esp_image: segment 1: paddr=0x0003f118 vaddr=0x3ffb0000 size=0x00f00 ( 3840) load�[0m �[0;32mI (184) esp_image: segment 2: paddr=0x00040020 vaddr=0x400d0020 size=0xc7854 (817236) map�[0m �[0;32mI (459) esp_image: segment 3: paddr=0x0010787c vaddr=0x3ffb0f00 size=0x05628 ( 22056) load�[0m �[0;32mI (468) esp_image: segment 4: paddr=0x0010ceac vaddr=0x40080000 size=0x00404 ( 1028) load�[0m �[0;32mI (468) esp_image: segment 5: paddr=0x0010d2b8 vaddr=0x40080404 size=0x1e134 (123188) load�[0m �[0;32mI (541) boot: Loaded app from partition at offset 0x10000�[0m �[0;32mI (541) boot: Disabling RNG early entropy source...�[0m �[0;32mI (541) psram: This chip is ESP32-D0WD�[0m �[0;32mI (546) spiram: Found 64MBit SPI RAM device�[0m �[0;32mI (550) spiram: SPI RAM mode: flash 80m sram 80m�[0m �[0;32mI (556) spiram: PSRAM initialized, cache is in low/high (2-core) mode.�[0m �[0;32mI (563) cpu_start: Pro cpu up.�[0m �[0;32mI (567) cpu_start: Application information:�[0m �[0;32mI (571) cpu_start: Project name: ctag-straempler�[0m �[0;32mI (577) cpu_start: App version: v0.9�[0m �[0;32mI (582) cpu_start: Compile time: Sep 11 2021 09:54:10�[0m �[0;32mI (588) cpu_start: ELF file SHA256: 32bab0cc5eb6c006...�[0m �[0;32mI (594) cpu_start: ESP-IDF: v4.1.2-95-gaeb66e1057�[0m �[0;32mI (600) cpu_start: Starting app cpu, entry point is 0x40081720�[0m �[0;32mI (592) cpu_start: App cpu up.�[0m �[0;32mI (1082) spiram: SPI SRAM memory test OK�[0m �[0;32mI (1083) heap_init: Initializing. RAM available for dynamic allocation:�[0m �[0;32mI (1083) heap_init: At 3FFAE6E0 len 00001920 (6 KiB): DRAM�[0m �[0;32mI (1089) heap_init: At 3FFBEEB0 len 00021150 (132 KiB): DRAM�[0m �[0;32mI (1096) heap_init: At 3FFE0440 len 00003AE0 (14 KiB): D/IRAM�[0m �[0;32mI (1102) heap_init: At 3FFE4350 len 0001BCB0 (111 KiB): D/IRAM�[0m �[0;32mI (1109) heap_init: At 4009E538 len 00001AC8 (6 KiB): IRAM�[0m �[0;32mI (1115) cpu_start: Pro cpu start user code�[0m �[0;32mI (1120) spiram: Adding pool of 4096K of external SPI memory to heap allocator�[0m �[0;32mI (1140) spi_flash: detected chip: generic�[0m �[0;32mI (1140) spi_flash: flash io: qio�[0m �[0;32mI (1140) cpu_start: Starting scheduler on PRO CPU.�[0m �[0;32mI (0) cpu_start: Starting scheduler on APP CPU.�[0m �[0;32mI (1149) SD: Initializing SD card�[0m �[0;32mI (1149) gpio: GPIO[13]| InputEn: 0| OutputEn: 1| OpenDrain: 0| Pullup: 0| Pulldown: 0| Intr:0 �[0m �[0;31mE (1219) sdmmc_sd: sdmmc_send_cmd_switch_func: sdmmc_send_cmd returned 0x109�[0m �[0;31mE (1219) SD: Failed to initialize the card (265). Make sure SD card lines have pull-up resistors in place.�[0m SPI: display device added to spi bus (1)

SPI: attached display device, speed=8000000

SPI: bus uses native pins: false

SPI: display init...

OK

SPI: Max rd speed = 1000000

SPI: Changed speed to 26666666

�[0;32mI (2679) gpio: GPIO[33]| InputEn: 1| OutputEn: 0| OpenDrain: 0| Pullup: 0| Pulldown: 0| Intr:2 �[0m �[0;32mI (2679) gpio: GPIO[34]| InputEn: 1| OutputEn: 0| OpenDrain: 0| Pullup: 0| Pulldown: 0| Intr:2 �[0m �[0;32mI (2689) gpio: GPIO[35]| InputEn: 1| OutputEn: 0| OpenDrain: 0| Pullup: 0| Pulldown: 0| Intr:2 �[0m �[0;32mI (2699) gpio: GPIO[36]| InputEn: 1| OutputEn: 0| OpenDrain: 0| Pullup: 0| Pulldown: 0| Intr:0 �[0m �[0;32mI (2709) gpio: GPIO[39]| InputEn: 1| OutputEn: 0| OpenDrain: 0| Pullup: 0| Pulldown: 0| Intr:0 �[0m �[0;32mI (2719) AUDIO: Starting audio task�[0m �[0;32mI (2719) I2S: DMA Malloc info, datalen=blocksize=256, dma_buf_count=4�[0m �[0;32mI (2729) I2S: DMA Malloc info, datalen=blocksize=256, dma_buf_count=4�[0m �[0;32mI (2749) I2S: APLL: Req RATE: 44100, real rate: 44099.988, BITS: 32, CLKM: 1, BCK_M: 8, MCLK: 22579194.000, SCLK: 2822399.250000, diva: 1, divb: 0�[0m �[0;31mE (2759) FILEIO: Could not open file /sdcard/CONFIG.JSN for reading�[0m �[0;31mE (2759) AUDIO: Couldn't open config.jsn�[0m �[0;31mE (2769) FILEIO: Could not open file /sdcard/CONFIG.JSN for reading�[0m �[0;31mE (2769) FILEIO: Could not open file /sdcard/banks/DEFAULT.JSN for reading�[0m �[0;31mE (2779) PRESET: Root is NULL�[0m �[0;31mE (2789) MENU: Error loading bank from file�[0m �[0;31mE (2789) MENU: Error loading bank�[0m �[0;31mE (2789) FILEIO: Could not open file /sdcard/CONFIG.JSN for reading�[0m �[0;31mE (2799) MENU: Error loading tz_shift from config�[0m I (2959) wifi:wifi driver task: 3ffdd804, prio:23, stack:6656, core=0 �[0;32mI (2959) system_api: Base MAC address is not set, read default base MAC address from BLK0 of EFUSE�[0m �[0;32mI (2959) system_api: Base MAC address is not set, read default base MAC address from BLK0 of EFUSE�[0m I (2979) wifi:wifi firmware version: 1424aca I (2979) wifi:config NVS flash: enabled I (2979) wifi:config nano formating: disabled I (2979) wifi:Init data frame dynamic rx buffer num: 32 I (2989) wifi:Init management frame dynamic rx buffer num: 32 I (2989) wifi:Init management short buffer num: 32 I (2999) wifi:Init static tx buffer num: 16 I (2999) wifi:Init static rx buffer size: 1600 I (3009) wifi:Init static rx buffer num: 10 I (3009) wifi:Init dynamic rx buffer num: 32 �[0;32mI (3019) wifi_init: rx ba win: 16�[0m �[0;32mI (3019) wifi_init: tcpip mbox: 32�[0m �[0;32mI (3019) wifi_init: udp mbox: 6�[0m �[0;32mI (3029) wifi_init: tcp mbox: 6�[0m �[0;32mI (3029) wifi_init: tcp tx win: 5744�[0m �[0;32mI (3039) wifi_init: tcp rx win: 5744�[0m �[0;32mI (3039) wifi_init: tcp mss: 1440�[0m �[0;32mI (3039) wifi_init: WiFi/LWIP prefer SPIRAM�[0m �[0;32mI (3049) wifi_init: WiFi IRAM OP enabled�[0m �[0;32mI (3049) wifi_init: WiFi RX IRAM OP enabled�[0m �[0;31mE (3059) FILEIO: Could not open file /sdcard/CONFIG.JSN for reading�[0m �[0;31mE (3059) FILEIO: root == NULL�[0m �[0;32mI (3069) WIFI: Setting WiFi configuration SSID ��⸮?��[0m �[0;32mI (3069) phy_init: phy_version 4660,0162888,Dec 23 2020�[0m I (3159) wifi:mode : sta (b8:f0:09:80:a9:d8)

Is there anything else that should be on SD card (heard about an excel file but could not find) - this is what I have

Folders

BANKS, POOl, RAW, USR

Files

Config.json and Silence.RAW

— Reply to this email directly, view it on GitHub https://github.com/ctag-fh-kiel/ctag-straempler/issues/18#issuecomment-1023288113, or unsubscribe https://github.com/notifications/unsubscribe-auth/ABZMGRTVKS5VLDYUFI6KYJ3UYFLPTANCNFSM5M4F5HBA . Triage notifications on the go with GitHub Mobile for iOS https://apps.apple.com/app/apple-store/id1477376905?ct=notification-email&mt=8&pt=524675 or Android https://play.google.com/store/apps/details?id=com.github.android&referrer=utm_campaign%3Dnotification-email%26utm_medium%3Demail%26utm_source%3Dgithub.

You are receiving this because you commented.Message ID: @.***>

polymer81 commented 2 years ago

Ok, great - now I understand how it works. Thanks for the help.