issues
search
dankamongmen
/
dankdryer
firmware for the world's best filament dryer
Apache License 2.0
6
stars
0
forks
source link
issues
Newest
Newest
Most commented
Recently updated
Oldest
Least commented
Least recently updated
attempt to sync time using ntp
#52
dankamongmen
opened
1 week ago
2
perform at least software calibration of ADC
#51
dankamongmen
closed
1 week ago
2
need a way to enter calibration mode for NAU7802
#50
dankamongmen
opened
1 week ago
0
make component mounts discrete from croom
#49
dankamongmen
closed
2 weeks ago
2
replace our tach counters with PCNT unit
#48
dankamongmen
opened
2 weeks ago
0
get actions working with esp-idf
#47
dankamongmen
closed
3 weeks ago
0
reject arduino API; use ESP-IDF
#46
dankamongmen
closed
3 weeks ago
0
dryer doesn't reconnect to mqtt server after disconnect
#45
dankamongmen
opened
1 month ago
1
implement "dry" command
#44
dankamongmen
closed
1 week ago
0
put cutaways into the hotbox for silica packets
#43
dankamongmen
closed
2 weeks ago
1
floating regions persist in croom
#42
dankamongmen
closed
2 weeks ago
4
need a hole in croom to feed hotbox fan cable through
#41
dankamongmen
closed
1 month ago
0
floating cantilevers in hotbox
#40
dankamongmen
closed
1 month ago
2
try to switch over to ESP32-S3 MCPWM, eliminating need for TB6612FNG
#39
dankamongmen
closed
1 month ago
1
change floor cuts to match the cylinder
#38
dankamongmen
closed
1 month ago
0
find cheaper motor
#37
dankamongmen
closed
1 month ago
1
mount 150C thermocouple in floor of hotbox
#36
dankamongmen
closed
1 month ago
1
find suitable printing service
#35
dankamongmen
closed
1 month ago
1
place croom at z=0
#34
dankamongmen
closed
1 month ago
1
make a PCB
#33
dankamongmen
opened
1 month ago
1
add 13.56MHz RFID reader to electronics + firmware
#32
dankamongmen
opened
1 month ago
1
round corners on the bottom
#31
dankamongmen
closed
1 month ago
5
get us building on github ci runner
#30
dankamongmen
closed
1 month ago
0
first stab at ubuntu_test.yml for github ci
#29
dankamongmen
closed
1 month ago
0
expose at least RO material through a webpage
#28
dankamongmen
closed
1 week ago
4
interoperate with mDNS
#27
dankamongmen
closed
1 month ago
2
thread all mounting holes
#26
dankamongmen
closed
1 month ago
1
read bambu rfid tags
#25
dankamongmen
opened
1 month ago
0
support factory reset
#24
dankamongmen
opened
1 month ago
0
support a setup mode where wifi is configured
#23
dankamongmen
opened
1 month ago
0
need temp sensor in hotbox capable of high temperatures
#22
dankamongmen
closed
1 week ago
3
need programmed control of heater
#21
dankamongmen
closed
1 week ago
3
read tach signal from fans
#20
dankamongmen
closed
1 month ago
4
send PWM signals to fans
#19
dankamongmen
closed
1 month ago
2
sample load cell and provide calibration
#18
dankamongmen
closed
1 week ago
2
support OTA
#17
dankamongmen
opened
1 month ago
5
get on wifi and talk to mqtt broker
#16
dankamongmen
closed
1 month ago
6
allow configuration over mqtt
#15
dankamongmen
closed
1 month ago
2
report all status over mqtt
#14
dankamongmen
closed
1 month ago
1
croom walls get thinner as they rise
#13
dankamongmen
closed
1 month ago
2
thicken hotbox walls and make croom walls thinner
#12
dankamongmen
closed
1 month ago
4
Design the central shaft
#11
dankamongmen
closed
1 month ago
2
Design an air shield for the load cell
#10
dankamongmen
closed
3 weeks ago
4
Replace heater mounts with mounting holes
#9
dankamongmen
closed
1 month ago
1
Locking mechanism for top
#8
dankamongmen
closed
3 weeks ago
4
Expand hotbox mounts to cover gaps in croom roof
#7
dankamongmen
closed
1 month ago
1
Strengthen motor mount front
#6
dankamongmen
closed
1 month ago
2
Move LMS horizontal spacing
#5
dankamongmen
closed
1 month ago
2
Move motor mount away from the wall
#4
dankamongmen
closed
1 month ago
4
Move AC adapter mounting holes apart horizontally
#3
dankamongmen
closed
1 month ago
3
Next