Homebridge Doorbird

HomeKit support for Doorbird video doorbells using Homebridge.

homebridge-doorbird is a plugin for Homebridge intended to give you an integrated experience with your Doorbird devices.

It provides the HomeKit video doorbell service which includes a camera, lock, motion sensor, and infrared light service, using the excellent homebridge-camera-ffmpeg as a foundation.

Requirements and Limitations

• Audio requires a version of FFmpeg that is compiled with fdk-aac support. This plugin uses ffmpeg-for-homebridge to streamline this for some of the more common operating systems. Check the ffmpeg-for-homebridge page for details on supported operating systems. If your operating system isn't supported, you'll need to compile your own. Instructions are beyond the scope of this plugin.

• Two-way audio is not currently supported. Currently, you can hear audio but the microphone capability is yet to be implemented.

Installation

If you are new to Homebridge, please first read the Homebridge documentation.

1. Install Homebridge:

   sudo npm install -g --unsafe-perm homebridge

2. Install homebridge-doorbird:

   sudo npm install -g --unsafe-perm homebridge-doorbird

Plugin configuration

Add the platform in config.json in your home directory inside .homebridge and edit the required fields. If you want audio support, make sure to enable the feature option Audio.Enable in options.

"platforms": [
  {
    "platform": "Doorbird",

    "doorbirds": [
      {
        "name": "Doorbird 1",
        "ip": "your.doorbird.ip",
        "username": "some-doorbird-user (or create a new one just for homebridge)",
        "password": "some-doorbird-password",
        "options": [ "Relay.Hide.2" ]
      }
    ]
  }
]

Feature Options

Feature options allow you to enable or disable certain features in this plugin. Feature options are specific to individual Doorbirds.

The feature options for individual Doorbird devices can be customized using the options setting inside the doorbirds section. Available options:

• Relay.Hide.relay - hide the relay named relay from being shown in HomeKit.

Night vision

Depending on your situation, you might benefit from having Doorbird's infrared light (aka night vision) turn on automatically for you.

This plugin supports the ability to enable night vision when the doorbell rings, HomeKit requests snapshots, or stream video. Night vision can be always-on or activated only at night, for supported events.

See advanced configuration for more details, or configure this plugin using the Homebridge webUI.

Command line scripts.

If you would like to configure a command line to execute when motion or doorbell events are triggered, you can configure the cmdDoorbell and cmdMotion, respectively.

Relays and peripheral devices

The default for this plugin is to lock or unlock the first relay (relay 1) in the Doorbird. This is typically a door strike that unlocks a gate or door.

Support for multiple relays is available on some Doorbird devices and on the following optionally attached peripheral devices:

• A1081 E/A Controller (https://www.doorbird.com/downloads/manual_a1081_en_de.pdf) - TESTED
• A1101 Indoor Station (https://www.doorbird.com/downloads/datasheet/datasheet_a1101_en.pdf) - UNTESTED

All relays found on the Doorbird, including peripherals, will be made available in HomeKit and the Home app.

You may switch the default relay using the primaryRelay configuration parameter. To identify the relay names to use, review the homebridge log and look for log entries beginning with detected relay: xxxx to identify the relay you wish to use by default. In the previous example, you would use "primaryRelay": "xxxx" to set xxxx as the default relay to unlock.

Example configuration for an alternate relay as the default:

"primaryRelay": "2"

Another example configuration using a relay on a peripheral device:

"primaryRelay": "gggggg@1"

The name of the controller or station can be found in the App: Administration > Peripherals > Device (6-letter word)

Advanced configuration (optional)

This step is not required. For those that prefer to tailor the defaults to their liking, here are the supported parameters.

"platforms": [
  {
    "platform": "Doorbird",
    "name": "Doorbird",
    "videoProcessor": "/usr/local/bin/ffmpeg",
    "ffmpegOptions": "-probesize 32 -analyzeduration 0 -fflags nobuffer -preset veryfast -refs 1 -x264-params intra-refresh=1:bframes=0",

    "doorbirds": [
      {
        "ip": "your.doorbird.ip",
        "username": "some-doorbird-user (or create a new one just for homebridge)",
        "password": "some-doorbird-password",
        "name": "My Doorbird",
        "nightVisionDoorbell": false,
        "nightVisionSnapshot": false,
        "nightVisionVideo": false,
        "nightVisionDoorbellNight": false,
        "nightVisionSnapshotNight": false,
        "nightVisionVideoNight": false,
        "primaryRelay": "1",
        "cmdDoorbell": "/some/doorbell/script",
        "cmdMotion": "/some/motion/script",
        "options": [ "Relay.Hide.2" ]
      }
    ]
  }
]

Platform-level configuration parameters:

doorbirds configuration parameters:

Credits

• homebridge-videodoorbell
• homebridge-camera-ffmpeg
• hjdhjd