#
#
#
This directory contains the source code for U-Boot, a boot loader for Embedded boards based on PowerPC, ARM, MIPS and several other processors, which can be installed in a boot ROM and used to initialize and test the hardware or to download and run application code.
The development of U-Boot is closely related to Linux: some parts of the source code originate in the Linux source tree, we have some header files in common, and special provision has been made to support booting of Linux images.
Some attention has been paid to make this software easily configurable and extendable. For instance, all monitor commands are implemented with the same call interface, so that it's very easy to add new commands. Also, instead of permanently adding rarely used code (for instance hardware test utilities) to the monitor, you can load and run it dynamically.
In general, all boards for which a configuration option exists in the Makefile have been tested to some extent and can be considered "working". In fact, many of them are used in production systems.
In case of problems see the CHANGELOG and CREDITS files to find out who contributed the specific port. The boards.cfg file lists board maintainers.
Note: There is no CHANGELOG file in the actual U-Boot source tree; it can be created dynamically from the Git log using:
make CHANGELOGIn case you have questions about, problems with or contributions for U-Boot you should send a message to the U-Boot mailing list at u-boot@lists.denx.de. There is also an archive of previous traffic on the mailing list - please search the archive before asking FAQ's. Please see http://lists.denx.de/pipermail/u-boot and http://dir.gmane.org/gmane.comp.boot-loaders.u-boot
The U-Boot source code is maintained in the git repository at git://www.denx.de/git/u-boot.git ; you can browse it online at http://www.denx.de/cgi-bin/gitweb.cgi?p=u-boot.git;a=summary
The "snapshot" links on this page allow you to download tarballs of any version you might be interested in. Official releases are also available for FTP download from the ftp://ftp.denx.de/pub/u-boot/ directory.
Pre-built (and tested) images are available from ftp://ftp.denx.de/pub/u-boot/images/
The "official" name of this project is "Das U-Boot". The spelling "U-Boot" shall be used in all written text (documentation, comments in source files etc.). Example:
This is the README file for the U-Boot project.File names etc. shall be based on the string "u-boot". Examples:
include/asm-ppc/u-boot.h
#include <asm/u-boot.h>Variable names, preprocessor constants etc. shall be either based on the string "u_boot" or on "U_BOOT". Example:
U_BOOT_VERSION u_boot_logo
IH_OS_U_BOOT u_boot_hush_startStarting with the release in October 2008, the names of the releases were changed from numerical release numbers without deeper meaning into a time stamp based numbering. Regular releases are identified by names consisting of the calendar year and month of the release date. Additional fields (if present) indicate release candidates or bug fix releases in "stable" maintenance trees.
Examples: U-Boot v2009.11 - Release November 2009 U-Boot v2009.11.1 - Release 1 in version November 2009 stable tree U-Boot v2010.09-rc1 - Release candiate 1 for September 2010 release
/arch Architecture specific files /arc Files generic to ARC architecture /cpu CPU specific files /arc700 Files specific to ARC 700 CPUs /lib Architecture specific library files /arm Files generic to ARM architecture /cpu CPU specific files /arm720t Files specific to ARM 720 CPUs /arm920t Files specific to ARM 920 CPUs /at91 Files specific to Atmel AT91RM9200 CPU /imx Files specific to Freescale MC9328 i.MX CPUs /s3c24x0 Files specific to Samsung S3C24X0 CPUs /arm926ejs Files specific to ARM 926 CPUs /arm1136 Files specific to ARM 1136 CPUs /pxa Files specific to Intel XScale PXA CPUs /sa1100 Files specific to Intel StrongARM SA1100 CPUs /lib Architecture specific library files /avr32 Files generic to AVR32 architecture /cpu CPU specific files /lib Architecture specific library files /blackfin Files generic to Analog Devices Blackfin architecture /cpu CPU specific files /lib Architecture specific library files /m68k Files generic to m68k architecture /cpu CPU specific files /mcf52x2 Files specific to Freescale ColdFire MCF52x2 CPUs /mcf5227x Files specific to Freescale ColdFire MCF5227x CPUs /mcf532x Files specific to Freescale ColdFire MCF5329 CPUs /mcf5445x Files specific to Freescale ColdFire MCF5445x CPUs /mcf547x_8x Files specific to Freescale ColdFire MCF547x_8x CPUs /lib Architecture specific library files /microblaze Files generic to microblaze architecture /cpu CPU specific files /lib Architecture specific library files /mips Files generic to MIPS architecture /cpu CPU specific files /mips32 Files specific to MIPS32 CPUs /mips64 Files specific to MIPS64 CPUs /lib Architecture specific library files /nds32 Files generic to NDS32 architecture /cpu CPU specific files /n1213 Files specific to Andes Technology N1213 CPUs /lib Architecture specific library files /nios2 Files generic to Altera NIOS2 architecture /cpu CPU specific files /lib Architecture specific library files /openrisc Files generic to OpenRISC architecture /cpu CPU specific files /lib Architecture specific library files /powerpc Files generic to PowerPC architecture /cpu CPU specific files /mpc5xx Files specific to Freescale MPC5xx CPUs /mpc5xxx Files specific to Freescale MPC5xxx CPUs /mpc8xx Files specific to Freescale MPC8xx CPUs /mpc8260 Files specific to Freescale MPC8260 CPUs /mpc85xx Files specific to Freescale MPC85xx CPUs /ppc4xx Files specific to AMCC PowerPC 4xx CPUs /lib Architecture specific library files /sh Files generic to SH architecture /cpu CPU specific files /sh2 Files specific to sh2 CPUs /sh3 Files specific to sh3 CPUs /sh4 Files specific to sh4 CPUs /lib Architecture specific library files /sparc Files generic to SPARC architecture /cpu CPU specific files /leon2 Files specific to Gaisler LEON2 SPARC CPU /leon3 Files specific to Gaisler LEON3 SPARC CPU /lib Architecture specific library files /x86 Files generic to x86 architecture /cpu CPU specific files /lib Architecture specific library files /api Machine/arch independent API for external apps /board Board dependent files /common Misc architecture independent functions /disk Code for disk drive partition handling /doc Documentation (don't expect too much) /drivers Commonly used device drivers /dts Contains Makefile for building internal U-Boot fdt. /examples Example code for standalone applications, etc. /fs Filesystem code (cramfs, ext2, jffs2, etc.) /include Header Files /lib Files generic to all architectures /libfdt Library files to support flattened device trees /lzma Library files to support LZMA decompression /lzo Library files to support LZO decompression /net Networking code /post Power On Self Test /spl Secondary Program Loader framework /tools Tools to build S-Record or U-Boot images, etc.
Configuration is usually done using C preprocessor defines; the rationale behind that is to avoid dead code whenever possible.
There are two classes of configuration variables:
Configuration OPTIONS: These are selectable by the user and have names beginning with "CONFIG_".
Configuration SETTINGS: These depend on the hardware etc. and should not be meddled with if you don't know what you're doing; they have names beginning with "CONFIGSYS".
Later we will add a configuration tool - probably similar to or even identical to what's used for the Linux kernel. Right now, we have to do the configuration by hand, which means creating some symbolic links and editing some configuration files. We use the TQM8xxL boards as an example here.
For all supported boards there are ready-to-use default
configurations available; just type "make
Example: For a TQM823L module type:
cd u-boot
make TQM823L_defconfigFor the Cogent platform, you need to specify the CPU type as well; e.g. "make cogent_mpc8xx_defconfig". And also configure the cogent directory according to the instructions in cogent/README.
U-Boot can be built natively to run on a Linux host using the 'sandbox' board. This allows feature development which is not board- or architecture- specific to be undertaken on a native platform. The sandbox is also used to run some of U-Boot's tests.
See board/sandbox/README.sandbox for more details.
This is the intended start-up flow for boards. This should apply for both SPL and U-Boot proper (i.e. they both follow the same rules). At present SPL mostly uses a separate code path, but the funtion names and roles of each function are the same. Some boards or architectures may not conform to this. At least most ARM boards which use CONFIG_SPL_FRAMEWORK conform to this.
Execution starts with start.S with three functions called during init after that. The purpose and limitations of each is described below.
lowlevel_init():
board_init_f():
BSS is not available, so you cannot use global/static variables, only stack variables and global_data
Non-SPL-specific notes:
dram_init() is called to set up DRAM. If already done in SPL this can do nothing
SPL-specific notes:
Here the BSS is cleared. For SPL, if CONFIG_SPL_STACK_R is defined, then at this point the stack and global_data are relocated to below CONFIG_SPL_STACK_R_ADDR. For non-SPL, U-Boot is relocated to run at the top of memory.
board_init_r():
execution eventually continues to main_loop()
Non-SPL-specific notes:
U-Boot is relocated to the top of memory and is now running from there.
SPL-specific notes:
Configuration depends on the combination of board and CPU type; all
such information is kept in a configuration file
"include/configs/
Example: For a TQM823L module, all configuration settings are in "include/configs/TQM823L.h".
Many of the options are named exactly as the corresponding Linux kernel configuration options. The intention is to make it easier to build a config tool - later.
The following options need to be configured:
CPU Type: Define exactly one, e.g. CONFIG_MPC85XX.
Board Type: Define exactly one, e.g. CONFIG_MPC8540ADS.
CPU Daughterboard Type: (if CONFIG_ATSTK1000 is defined) Define exactly one, e.g. CONFIG_ATSTK1002
CPU Module Type: (if CONFIG_COGENT is defined) Define exactly one of CONFIG_CMA286_60_OLD --- FIXME --- not tested yet: CONFIG_CMA286_60, CONFIG_CMA286_21, CONFIG_CMA286_60P, CONFIG_CMA287_23, CONFIG_CMA287_50
Motherboard Type: (if CONFIG_COGENT is defined) Define exactly one of CONFIG_CMA101, CONFIG_CMA102
Motherboard I/O Modules: (if CONFIG_COGENT is defined) Define one or more of CONFIG_CMA302
Motherboard Options: (if CONFIG_CMA101 or CONFIG_CMA102 are defined) Define one or more of CONFIG_LCD_HEARTBEAT - update a character position on the LCD display every second with a "rotator" |-/|-/
Marvell Family Member CONFIG_SYS_MVFS - define it if you want to enable multiple fs option at one time for marvell soc family
8xx CPU Options: (if using an MPC8xx CPU) CONFIG_8xx_GCLK_FREQ - deprecated: CPU clock if get_gclk_freq() cannot work e.g. if there is no 32KHz reference PIT/RTC clock CONFIG_8xx_OSCLK - PLL input clock (either EXTCLK or XTAL/EXTAL)
859/866/885 CPU options: (if using a MPC859 or MPC866 or MPC885 CPU): CONFIG_SYS_8xx_CPUCLK_MIN CONFIG_SYS_8xx_CPUCLK_MAX CONFIG_8xx_CPUCLK_DEFAULT See doc/README.MPC866
CONFIG_SYS_MEASURE_CPUCLK
Define this to measure the actual CPU clock instead
of relying on the correctness of the configured
values. Mostly useful for board bringup to make sure
the PLL is locked at the intended frequency. Note
that this requires a (stable) reference clock (32 kHz
RTC clock or CONFIG_SYS_8XX_XIN)
CONFIG_SYS_DELAYED_ICACHE
Define this option if you want to enable the
ICache only when Code runs from RAM.85xx CPU Options: CONFIG_SYS_PPC64
Specifies that the core is a 64-bit PowerPC implementation (implements
the "64" category of the Power ISA). This is necessary for ePAPR
compliance, among other possible reasons.
CONFIG_SYS_FSL_TBCLK_DIV
Defines the core time base clock divider ratio compared to the
system clock. On most PQ3 devices this is 8, on newer QorIQ
devices it can be 16 or 32. The ratio varies from SoC to Soc.
CONFIG_SYS_FSL_PCIE_COMPAT
Defines the string to utilize when trying to match PCIe device
tree nodes for the given platform.
CONFIG_SYS_PPC_E500_DEBUG_TLB
Enables a temporary TLB entry to be used during boot to work
around limitations in e500v1 and e500v2 external debugger
support. This reduces the portions of the boot code where
breakpoints and single stepping do not work. The value of this
symbol should be set to the TLB1 entry to be used for this
purpose.
CONFIG_SYS_FSL_ERRATUM_A004510
Enables a workaround for erratum A004510. If set,
then CONFIG_SYS_FSL_ERRATUM_A004510_SVR_REV and
CONFIG_SYS_FSL_CORENET_SNOOPVEC_COREONLY must be set.
CONFIG_SYS_FSL_ERRATUM_A004510_SVR_REV
CONFIG_SYS_FSL_ERRATUM_A004510_SVR_REV2 (optional)
Defines one or two SoC revisions (low 8 bits of SVR)
for which the A004510 workaround should be applied.
The rest of SVR is either not relevant to the decision
of whether the erratum is present (e.g. p2040 versus
p2041) or is implied by the build target, which controls
whether CONFIG_SYS_FSL_ERRATUM_A004510 is set.
See Freescale App Note 4493 for more information about
this erratum.
CONFIG_A003399_NOR_WORKAROUND
Enables a workaround for IFC erratum A003399. It is only
required during NOR boot.
CONFIG_A008044_WORKAROUND
Enables a workaround for T1040/T1042 erratum A008044. It is only
required during NAND boot and valid for Rev 1.0 SoC revision
CONFIG_SYS_FSL_CORENET_SNOOPVEC_COREONLY
This is the value to write into CCSR offset 0x18600
according to the A004510 workaround.
CONFIG_SYS_FSL_DSP_DDR_ADDR
This value denotes start offset of DDR memory which is
connected exclusively to the DSP cores.
CONFIG_SYS_FSL_DSP_M2_RAM_ADDR
This value denotes start offset of M2 memory
which is directly connected to the DSP core.
CONFIG_SYS_FSL_DSP_M3_RAM_ADDR
This value denotes start offset of M3 memory which is directly
connected to the DSP core.
CONFIG_SYS_FSL_DSP_CCSRBAR_DEFAULT
This value denotes start offset of DSP CCSR space.
CONFIG_SYS_FSL_SINGLE_SOURCE_CLK
Single Source Clock is clocking mode present in some of FSL SoC's.
In this mode, a single differential clock is used to supply
clocks to the sysclock, ddrclock and usbclock.
CONFIG_SYS_CPC_REINIT_F
This CONFIG is defined when the CPC is configured as SRAM at the
time of U-boot entry and is required to be re-initialized.
CONFIG_DEEP_SLEEP
Indicates this SoC supports deep sleep feature. If deep sleep is
supported, core will start to execute uboot when wakes up.Generic CPU options: CONFIG_SYS_GENERIC_GLOBAL_DATA Defines global data is initialized in generic board board_init_f(). If this macro is defined, global data is created and cleared in generic board board_init_f(). Without this macro, architecture/board should initialize global data before calling board_init_f().
CONFIG_SYS_BIG_ENDIAN, CONFIG_SYS_LITTLE_ENDIAN
Defines the endianess of the CPU. Implementation of those
values is arch specific.
CONFIG_SYS_FSL_DDR
Freescale DDR driver in use. This type of DDR controller is
found in mpc83xx, mpc85xx, mpc86xx as well as some ARM core
SoCs.
CONFIG_SYS_FSL_DDR_ADDR
Freescale DDR memory-mapped register base.
CONFIG_SYS_FSL_DDR_EMU
Specify emulator support for DDR. Some DDR features such as
deskew training are not available.
CONFIG_SYS_FSL_DDRC_GEN1
Freescale DDR1 controller.
CONFIG_SYS_FSL_DDRC_GEN2
Freescale DDR2 controller.
CONFIG_SYS_FSL_DDRC_GEN3
Freescale DDR3 controller.
CONFIG_SYS_FSL_DDRC_GEN4
Freescale DDR4 controller.
CONFIG_SYS_FSL_DDRC_ARM_GEN3
Freescale DDR3 controller for ARM-based SoCs.
CONFIG_SYS_FSL_DDR1
Board config to use DDR1. It can be enabled for SoCs with
Freescale DDR1 or DDR2 controllers, depending on the board
implemetation.
CONFIG_SYS_FSL_DDR2
Board config to use DDR2. It can be eanbeld for SoCs with
Freescale DDR2 or DDR3 controllers, depending on the board
implementation.
CONFIG_SYS_FSL_DDR3
Board config to use DDR3. It can be enabled for SoCs with
Freescale DDR3 or DDR3L controllers.
CONFIG_SYS_FSL_DDR3L
Board config to use DDR3L. It can be enabled for SoCs with
DDR3L controllers.
CONFIG_SYS_FSL_DDR4
Board config to use DDR4. It can be enabled for SoCs with
DDR4 controllers.
CONFIG_SYS_FSL_IFC_BE
Defines the IFC controller register space as Big Endian
CONFIG_SYS_FSL_IFC_LE
Defines the IFC controller register space as Little Endian
CONFIG_SYS_FSL_PBL_PBI
It enables addition of RCW (Power on reset configuration) in built image.
Please refer doc/README.pblimage for more details
CONFIG_SYS_FSL_PBL_RCW
It adds PBI(pre-boot instructions) commands in u-boot build image.
PBI commands can be used to configure SoC before it starts the execution.
Please refer doc/README.pblimage for more details
CONFIG_SPL_FSL_PBL
It adds a target to create boot binary having SPL binary in PBI format
concatenated with u-boot binary.
CONFIG_SYS_FSL_DDR_BE
Defines the DDR controller register space as Big Endian
CONFIG_SYS_FSL_DDR_LE
Defines the DDR controller register space as Little Endian
CONFIG_SYS_FSL_DDR_SDRAM_BASE_PHY
Physical address from the view of DDR controllers. It is the
same as CONFIG_SYS_DDR_SDRAM_BASE for all Power SoCs. But
it could be different for ARM SoCs.
CONFIG_SYS_FSL_DDR_INTLV_256B
DDR controller interleaving on 256-byte. This is a special
interleaving mode, handled by Dickens for Freescale layerscape
SoCs with ARM core.
CONFIG_SYS_FSL_DDR_MAIN_NUM_CTRLS
Number of controllers used as main memory.
CONFIG_SYS_FSL_OTHER_DDR_NUM_CTRLS
Number of controllers used for other than main memory.
CONFIG_SYS_FSL_SEC_BE
Defines the SEC controller register space as Big Endian
CONFIG_SYS_FSL_SEC_LE
Defines the SEC controller register space as Little EndianIntel Monahans options: CONFIG_SYS_MONAHANS_RUN_MODE_OSC_RATIO
Defines the Monahans run mode to oscillator
ratio. Valid values are 8, 16, 24, 31. The core
frequency is this value multiplied by 13 MHz.
CONFIG_SYS_MONAHANS_TURBO_RUN_MODE_RATIO
Defines the Monahans turbo mode to oscillator
ratio. Valid values are 1 (default if undefined) and
2. The core frequency as calculated above is multiplied
by this value.MIPS CPU options: CONFIG_SYS_INIT_SP_OFFSET
Offset relative to CONFIG_SYS_SDRAM_BASE for initial stack
pointer. This is needed for the temporary stack before
relocation.
CONFIG_SYS_MIPS_CACHE_MODE
Cache operation mode for the MIPS CPU.
See also arch/mips/include/asm/mipsregs.h.
Possible values are:
CONF_CM_CACHABLE_NO_WA
CONF_CM_CACHABLE_WA
CONF_CM_UNCACHED
CONF_CM_CACHABLE_NONCOHERENT
CONF_CM_CACHABLE_CE
CONF_CM_CACHABLE_COW
CONF_CM_CACHABLE_CUW
CONF_CM_CACHABLE_ACCELERATED
CONFIG_SYS_XWAY_EBU_BOOTCFG
Special option for Lantiq XWAY SoCs for booting from NOR flash.
See also arch/mips/cpu/mips32/start.S.
CONFIG_XWAY_SWAP_BYTES
Enable compilation of tools/xway-swap-bytes needed for Lantiq
XWAY SoCs for booting from NOR flash. The U-Boot image needs to
be swapped if a flash programmer is used.ARM options: CONFIG_SYS_EXCEPTION_VECTORS_HIGH
Select high exception vectors of the ARM core, e.g., do not
clear the V bit of the c1 register of CP15.
CONFIG_SYS_THUMB_BUILD
Use this flag to build U-Boot using the Thumb instruction
set for ARM architectures. Thumb instruction set provides
better code density. For ARM architectures that support
Thumb2 this flag will result in Thumb2 code generated by
GCC.
CONFIG_ARM_ERRATA_716044
CONFIG_ARM_ERRATA_742230
CONFIG_ARM_ERRATA_743622
CONFIG_ARM_ERRATA_751472
CONFIG_ARM_ERRATA_794072
CONFIG_ARM_ERRATA_761320
If set, the workarounds for these ARM errata are applied early
during U-Boot startup. Note that these options force the
workarounds to be applied; no CPU-type/version detection
exists, unlike the similar options in the Linux kernel. Do not
set these options unless they apply!
COUNTER_FREQUENCY
Generic timer clock source frequency.
COUNTER_FREQUENCY_REAL
Generic timer clock source frequency if the real clock is
different from COUNTER_FREQUENCY, and can only be determined
at run time.
NOTE: The following can be machine specific errata. These
do have ability to provide rudimentary version and machine
specific checks, but expect no product checks.
CONFIG_ARM_ERRATA_430973
CONFIG_ARM_ERRATA_454179
CONFIG_ARM_ERRATA_621766
CONFIG_ARM_ERRATA_798870Tegra SoC options: CONFIG_TEGRA_SUPPORT_NON_SECURE
Support executing U-Boot in non-secure (NS) mode. Certain
impossible actions will be skipped if the CPU is in NS mode,
such as ARM architectural timer initialization.Linux Kernel Interface: CONFIG_CLOCKS_IN_MHZ
U-Boot stores all clock information in Hz
internally. For binary compatibility with older Linux
kernels (which expect the clocks passed in the
bd_info data to be in MHz) the environment variable
"clocks_in_mhz" can be defined so that U-Boot
converts clock data to MHZ before passing it to the
Linux kernel.
When CONFIG_CLOCKS_IN_MHZ is defined, a definition of
"clocks_in_mhz=1" is automatically included in the
default environment.
CONFIG_MEMSIZE_IN_BYTES [relevant for MIPS only]
When transferring memsize parameter to Linux, some versions
expect it to be in bytes, others in MB.
Define CONFIG_MEMSIZE_IN_BYTES to make it in bytes.
CONFIG_OF_LIBFDT
New kernel versions are expecting firmware settings to be
passed using flattened device trees (based on open firmware
concepts).
CONFIG_OF_LIBFDT
* New libfdt-based support
* Adds the "fdt" command
* The bootm command automatically updates the fdt
OF_CPU - The proper name of the cpus node (only required for
MPC512X and MPC5xxx based boards).
OF_SOC - The proper name of the soc node (only required for
MPC512X and MPC5xxx based boards).
OF_TBCLK - The timebase frequency.
OF_STDOUT_PATH - The path to the console device
boards with QUICC Engines require OF_QE to set UCC MAC
addresses
CONFIG_OF_BOARD_SETUP
Board code has addition modification that it wants to make
to the flat device tree before handing it off to the kernel
CONFIG_OF_SYSTEM_SETUP
Other code has addition modification that it wants to make
to the flat device tree before handing it off to the kernel.
This causes ft_system_setup() to be called before booting
the kernel.
CONFIG_OF_BOOT_CPU
This define fills in the correct boot CPU in the boot
param header, the default value is zero if undefined.
CONFIG_OF_IDE_FIXUP
U-Boot can detect if an IDE device is present or not.
If not, and this new config option is activated, U-Boot
removes the ATA node from the DTS before booting Linux,
so the Linux IDE driver does not probe the device and
crash. This is needed for buggy hardware (uc101) where
no pull down resistor is connected to the signal IDE5V_DD7.
CONFIG_MACH_TYPE [relevant for ARM only][mandatory]
This setting is mandatory for all boards that have only one
machine type and must be used to specify the machine type
number as it appears in the ARM machine registry
(see http://www.arm.linux.org.uk/developer/machines/).
Only boards that have multiple machine types supported
in a single configuration file and the machine type is
runtime discoverable, do not have to use this setting.vxWorks boot parameters:
bootvx constructs a valid bootline using the following
environments variables: bootfile, ipaddr, serverip, hostname.
It loads the vxWorks image pointed bootfile.
CONFIG_SYS_VXWORKS_BOOT_DEVICE - The vxworks device name
CONFIG_SYS_VXWORKS_MAC_PTR - Ethernet 6 byte MA -address
CONFIG_SYS_VXWORKS_SERVERNAME - Name of the server
CONFIG_SYS_VXWORKS_BOOT_ADDR - Address of boot parameters
CONFIG_SYS_VXWORKS_ADD_PARAMS
Add it at the end of the bootline. E.g "u=username pw=secret"
Note: If a "bootargs" environment is defined, it will overwride
the defaults discussed just above.Cache Configuration: CONFIG_SYS_ICACHE_OFF - Do not enable instruction cache in U-Boot CONFIG_SYS_DCACHE_OFF - Do not enable data cache in U-Boot CONFIG_SYS_L2CACHE_OFF- Do not enable L2 cache in U-Boot
Cache Configuration for ARM: CONFIG_SYS_L2_PL310 - Enable support for ARM PL310 L2 cache controller CONFIG_SYS_PL310_BASE - Physical base address of PL310 controller register space
Serial Ports: CONFIG_PL010_SERIAL
Define this if you want support for Amba PrimeCell PL010 UARTs.
CONFIG_PL011_SERIAL
Define this if you want support for Amba PrimeCell PL011 UARTs.
CONFIG_PL011_CLOCK
If you have Amba PrimeCell PL011 UARTs, set this variable to
the clock speed of the UARTs.
CONFIG_PL01x_PORTS
If you have Amba PrimeCell PL010 or PL011 UARTs on your board,
define this to a list of base addresses for each (supported)
port. See e.g. include/configs/versatile.h
CONFIG_PL011_SERIAL_RLCR
Some vendor versions of PL011 serial ports (e.g. ST-Ericsson U8500)
have separate receive and transmit line control registers. Set
this variable to initialize the extra register.
CONFIG_PL011_SERIAL_FLUSH_ON_INIT
On some platforms (e.g. U8500) U-Boot is loaded by a second stage
boot loader that has already initialized the UART. Define this
variable to flush the UART at init time.
CONFIG_SERIAL_HW_FLOW_CONTROL
Define this variable to enable hw flow control in serial driver.
Current user of this option is drivers/serial/nsl16550.c driverConsole Interface: Depending on board, define exactly one serial port (like CONFIG_8xx_CONS_SMC1, CONFIG_8xx_CONS_SMC2, CONFIG_8xx_CONS_SCC1, ...), or switch off the serial console by defining CONFIG_8xx_CONS_NONE
Note: if CONFIG_8xx_CONS_NONE is defined, the serial
port routines must be defined elsewhere
(i.e. serial_init(), serial_getc(), ...)
CONFIG_CFB_CONSOLE
Enables console device for a color framebuffer. Needs following
defines (cf. smiLynxEM, i8042)
VIDEO_FB_LITTLE_ENDIAN graphic memory organisation
(default big endian)
VIDEO_HW_RECTFILL graphic chip supports
rectangle fill
(cf. smiLynxEM)
VIDEO_HW_BITBLT graphic chip supports
bit-blit (cf. smiLynxEM)
VIDEO_VISIBLE_COLS visible pixel columns
(cols=pitch)
VIDEO_VISIBLE_ROWS visible pixel rows
VIDEO_PIXEL_SIZE bytes per pixel
VIDEO_DATA_FORMAT graphic data format
(0-5, cf. cfb_console.c)
VIDEO_FB_ADRS framebuffer address
VIDEO_KBD_INIT_FCT keyboard int fct
(i.e. i8042_kbd_init())
VIDEO_TSTC_FCT test char fct
(i.e. i8042_tstc)
VIDEO_GETC_FCT get char fct
(i.e. i8042_getc)
CONFIG_CONSOLE_CURSOR cursor drawing on/off
(requires blink timer
cf. i8042.c)
CONFIG_SYS_CONSOLE_BLINK_COUNT blink interval (cf. i8042.c)
CONFIG_CONSOLE_TIME display time/date info in
upper right corner
(requires CONFIG_CMD_DATE)
CONFIG_VIDEO_LOGO display Linux logo in
upper left corner
CONFIG_VIDEO_BMP_LOGO use bmp_logo.h instead of
linux_logo.h for logo.
Requires CONFIG_VIDEO_LOGO
CONFIG_CONSOLE_EXTRA_INFO
additional board info beside
the logo
When CONFIG_CFB_CONSOLE_ANSI is defined, console will support
a limited number of ANSI escape sequences (cursor control,
erase functions and limited graphics rendition control).
When CONFIG_CFB_CONSOLE is defined, video console is
default i/o. Serial console can be forced with
environment 'console=serial'.
When CONFIG_SILENT_CONSOLE is defined, all console
messages (by U-Boot and Linux!) can be silenced with
the "silent" environment variable. See
doc/README.silent for more information.
CONFIG_SYS_CONSOLE_BG_COL: define the backgroundcolor, default
is 0x00.
CONFIG_SYS_CONSOLE_FG_COL: define the foregroundcolor, default
is 0xa0.Console Baudrate: CONFIG_BAUDRATE - in bps Select one of the baudrates listed in CONFIG_SYS_BAUDRATE_TABLE, see below. CONFIG_SYS_BRGCLK_PRESCALE, baudrate prescale
Console Rx buffer length With CONFIG_SYS_SMC_RXBUFLEN it is possible to define the maximum receive buffer length for the SMC. This option is actual only for 82xx and 8xx possible. If using CONFIG_SYS_SMC_RXBUFLEN also CONFIG_SYS_MAXIDLE must be defined, to setup the maximum idle timeout for the SMC.
Pre-Console Buffer: Prior to the console being initialised (i.e. serial UART initialised etc) all console output is silently discarded. Defining CONFIG_PRE_CONSOLE_BUFFER will cause U-Boot to buffer any console messages prior to the console being initialised to a buffer of size CONFIG_PRE_CON_BUF_SZ bytes located at CONFIG_PRE_CON_BUF_ADDR. The buffer is a circular buffer, so if more than CONFIG_PRE_CON_BUF_SZ bytes are output before the console is initialised, the earlier bytes are discarded.
Note that when printing the buffer a copy is made on the
stack so CONFIG_PRE_CON_BUF_SZ must fit on the stack.
'Sane' compilers will generate smaller code if
CONFIG_PRE_CON_BUF_SZ is a power of 2Safe printf() functions Define CONFIG_SYS_VSNPRINTF to compile in safe versions of the printf() functions. These are defined in include/vsprintf.h and include snprintf(), vsnprintf() and so on. Code size increase is approximately 300-500 bytes. If this option is not given then these functions will silently discard their buffer size argument - this means you are not getting any overflow checking in this case.
Boot Delay: CONFIG_BOOTDELAY - in seconds Delay before automatically booting the default image; set to -1 to disable autoboot. set to -2 to autoboot with no delay and not check for abort (even when CONFIG_ZERO_BOOTDELAY_CHECK is defined).
See doc/README.autoboot for these options that
work with CONFIG_BOOTDELAY. None are required.
CONFIG_BOOT_RETRY_TIME
CONFIG_BOOT_RETRY_MIN
CONFIG_AUTOBOOT_KEYED
CONFIG_AUTOBOOT_PROMPT
CONFIG_AUTOBOOT_DELAY_STR
CONFIG_AUTOBOOT_STOP_STR
CONFIG_ZERO_BOOTDELAY_CHECK
CONFIG_RESET_TO_RETRYAutoboot Command: CONFIG_BOOTCOMMAND Only needed when CONFIG_BOOTDELAY is enabled; define a command string that is automatically executed when no character is read on the console interface within "Boot Delay" after reset.
CONFIG_BOOTARGS
This can be used to pass arguments to the bootm
command. The value of CONFIG_BOOTARGS goes into the
environment value "bootargs".
CONFIG_RAMBOOT and CONFIG_NFSBOOT
The value of these goes into the environment as
"ramboot" and "nfsboot" respectively, and can be used
as a convenience, when switching between booting from
RAM and NFS.Bootcount: CONFIG_BOOTCOUNT_LIMIT Implements a mechanism for detecting a repeating reboot cycle, see: http://www.denx.de/wiki/view/DULG/UBootBootCountLimit
CONFIG_BOOTCOUNT_ENV
If no softreset save registers are found on the hardware
"bootcount" is stored in the environment. To prevent a
saveenv on all reboots, the environment variable
"upgrade_available" is used. If "upgrade_available" is
0, "bootcount" is always 0, if "upgrade_available" is
1 "bootcount" is incremented in the environment.
So the Userspace Applikation must set the "upgrade_available"
and "bootcount" variable to 0, if a boot was successfully.Pre-Boot Commands: CONFIG_PREBOOT
When this option is #defined, the existence of the
environment variable "preboot" will be checked
immediately before starting the CONFIG_BOOTDELAY
countdown and/or running the auto-boot command resp.
entering interactive mode.
This feature is especially useful when "preboot" is
automatically generated or modified. For an example
see the LWMON board specific code: here "preboot" is
modified when the user holds down a certain
combination of keys on the (special) keyboard when
booting the systemsSerial Download Echo Mode: CONFIG_LOADS_ECHO If defined to 1, all characters received during a serial download (using the "loads" command) are echoed back. This might be needed by some terminal emulations (like "cu"), but may as well just take time on others. This setting #define's the initial value of the "loads_echo" environment variable.
Kgdb Serial Baudrate: (if CONFIG_CMD_KGDB is defined) CONFIG_KGDB_BAUDRATE Select one of the baudrates listed in CONFIG_SYS_BAUDRATE_TABLE, see below.
Monitor Functions: Monitor commands can be included or excluded from the build by using the #include files
Regular expression support: CONFIG_REGEX If this variable is defined, U-Boot is linked against the SLRE (Super Light Regular Expression) library, which adds regex support to some commands, as for example "env grep" and "setexpr".
Device tree: CONFIG_OF_CONTROL If this variable is defined, U-Boot will use a device tree to configure its devices, instead of relying on statically compiled #defines in the board file. This option is experimental and only available on a few boards. The device tree is available in the global data as gd->fdt_blob.
U-Boot needs to get its device tree from somewhere. This can
be done using one of the two options below:
CONFIG_OF_EMBED
If this variable is defined, U-Boot will embed a device tree
binary in its image. This device tree file should be in the
board directory and called <soc>-<board>.dts. The binary file
is then picked up in board_init_f() and made available through
the global data structure as gd->blob.
CONFIG_OF_SEPARATE
If this variable is defined, U-Boot will build a device tree
binary. It will be called u-boot.dtb. Architecture-specific
code will locate it at run-time. Generally this works by:
cat u-boot.bin u-boot.dtb >image.bin
and in fact, U-Boot does this for you, creating a file called
u-boot-dtb.bin which is useful in the common case. You can
still use the individual files if you need something more
exotic.Watchdog: CONFIG_WATCHDOG If this variable is defined, it enables watchdog support for the SoC. There must be support in the SoC specific code for a watchdog. For the 8xx and 8260 CPUs, the SIU Watchdog feature is enabled in the SYPCR register. When supported for a specific SoC is available, then no further board specific code should be needed to use it.
CONFIG_HW_WATCHDOG
When using a watchdog circuitry external to the used
SoC, then define this variable and provide board
specific code for the "hw_watchdog_reset" function.
CONFIG_AT91_HW_WDT_TIMEOUT
specify the timeout in seconds. default 2 seconds.U-Boot Version: CONFIG_VERSION_VARIABLE If this variable is defined, an environment variable named "ver" is created by U-Boot showing the U-Boot version as printed by the "version" command. Any change to this variable will be reverted at the next reset.
Real-Time Clock:
When CONFIG_CMD_DATE is selected, the type of the RTC
has to be selected, too. Define exactly one of the
following options:
CONFIG_RTC_MPC8xx - use internal RTC of MPC8xx
CONFIG_RTC_PCF8563 - use Philips PCF8563 RTC
CONFIG_RTC_MC13XXX - use MC13783 or MC13892 RTC
CONFIG_RTC_MC146818 - use MC146818 RTC
CONFIG_RTC_DS1307 - use Maxim, Inc. DS1307 RTC
CONFIG_RTC_DS1337 - use Maxim, Inc. DS1337 RTC
CONFIG_RTC_DS1338 - use Maxim, Inc. DS1338 RTC
CONFIG_RTC_DS1339 - use Maxim, Inc. DS1339 RTC
CONFIG_RTC_DS164x - use Dallas DS164x RTC
CONFIG_RTC_ISL1208 - use Intersil ISL1208 RTC
CONFIG_RTC_MAX6900 - use Maxim, Inc. MAX6900 RTC
CONFIG_SYS_RTC_DS1337_NOOSC - Turn off the OSC output for DS1337
CONFIG_SYS_RV3029_TCR - enable trickle charger on
RV3029 RTC.
Note that if the RTC uses I2C, then the I2C interface
must also be configured. See I2C Support, below.GPIO Support: CONFIG_PCA953X - use NXP's PCA953X series I2C GPIO
The CONFIG_SYS_I2C_PCA953X_WIDTH option specifies a list of
chip-ngpio pairs that tell the PCA953X driver the number of
pins supported by a particular chip.
Note that if the GPIO device uses I2C, then the I2C interface
must also be configured. See I2C Support, below.I/O tracing:
When CONFIG_IO_TRACE is selected, U-Boot intercepts all I/O
accesses and can checksum them or write a list of them out
to memory. See the 'iotrace' command for details. This is
useful for testing device drivers since it can confirm that
the driver behaves the same way before and after a code
change. Currently this is supported on sandbox and arm. To
add support for your architecture, add '#include
Example output from the 'iotrace stats' command is below.
Note that if the trace buffer is exhausted, the checksum will
still continue to operate.
iotrace is enabled
Start: 10000000 (buffer start address)
Size: 00010000 (buffer size)
Offset: 00000120 (current buffer offset)
Output: 10000120 (start + offset)
Count: 00000018 (number of trace records)
CRC32: 9526fb66 (CRC32 of all trace records)Timestamp Support:
When CONFIG_TIMESTAMP is selected, the timestamp
(date and time) of an image is printed by image
commands like bootm or iminfo. This option is
automatically enabled when you select CONFIG_CMD_DATE .Partition Labels (disklabels) Supported: Zero or more of the following: CONFIG_MAC_PARTITION Apple's MacOS partition table. CONFIG_DOS_PARTITION MS Dos partition table, traditional on the Intel architecture, USB sticks, etc. CONFIG_ISO_PARTITION ISO partition table, used on CDROM etc. CONFIG_EFI_PARTITION GPT partition table, common when EFI is the bootloader. Note 2TB partition limit; see disk/part_efi.c CONFIG_MTD_PARTITIONS Memory Technology Device partition table.
If IDE or SCSI support is enabled (CONFIG_CMD_IDE or
CONFIG_CMD_SCSI) you must configure support for at
least one non-MTD partition type as well.IDE Reset method: CONFIG_IDE_RESET_ROUTINE - this is defined in several board configurations files but used nowhere!
CONFIG_IDE_RESET - is this is defined, IDE Reset will
be performed by calling the function
ide_set_reset(int reset)
which has to be defined in a board specific fileATAPI Support: CONFIG_ATAPI
Set this to enable ATAPI support.LBA48 Support CONFIG_LBA48
Set this to enable support for disks larger than 137GB
Also look at CONFIG_SYS_64BIT_LBA.
Whithout these , LBA48 support uses 32bit variables and will 'only'
support disks up to 2.1TB.
CONFIG_SYS_64BIT_LBA:
When enabled, makes the IDE subsystem use 64bit sector addresses.
Default is 32bit.SCSI Support: At the moment only there is only support for the SYM53C8XX SCSI controller; define CONFIG_SCSI_SYM53C8XX to enable it.
CONFIG_SYS_SCSI_MAX_LUN [8], CONFIG_SYS_SCSI_MAX_SCSI_ID [7] and
CONFIG_SYS_SCSI_MAX_DEVICE [CONFIG_SYS_SCSI_MAX_SCSI_ID *
CONFIG_SYS_SCSI_MAX_LUN] can be adjusted to define the
maximum numbers of LUNs, SCSI ID's and target
devices.
CONFIG_SYS_SCSI_SYM53C8XX_CCF to fix clock timing (80Mhz)
The environment variable 'scsidevs' is set to the number of
SCSI devices found during the last scan.NETWORK Support (PCI): CONFIG_E1000 Support for Intel 8254x/8257x gigabit chips.
CONFIG_E1000_SPI
Utility code for direct access to the SPI bus on Intel 8257x.
This does not do anything useful unless you set at least one
of CONFIG_CMD_E1000 or CONFIG_E1000_SPI_GENERIC.
CONFIG_E1000_SPI_GENERIC
Allow generic access to the SPI bus on the Intel 8257x, for
example with the "sspi" command.
CONFIG_CMD_E1000
Management command for E1000 devices. When used on devices
with SPI support you can reprogram the EEPROM from U-Boot.
CONFIG_E1000_FALLBACK_MAC
default MAC for empty EEPROM after production.
CONFIG_EEPRO100
Support for Intel 82557/82559/82559ER chips.
Optional CONFIG_EEPRO100_SROM_WRITE enables EEPROM
write routine for first time initialisation.
CONFIG_TULIP
Support for Digital 2114x chips.
Optional CONFIG_TULIP_SELECT_MEDIA for board specific
modem chip initialisation (KS8761/QS6611).
CONFIG_NATSEMI
Support for National dp83815 chips.
CONFIG_NS8382X
Support for National dp8382[01] gigabit chips.NETWORK Support (other):
CONFIG_DRIVER_AT91EMAC
Support for AT91RM9200 EMAC.
CONFIG_RMII
Define this to use reduced MII inteface
CONFIG_DRIVER_AT91EMAC_QUIET
If this defined, the driver is quiet.
The driver doen't show link status messages.
CONFIG_CALXEDA_XGMAC
Support for the Calxeda XGMAC device
CONFIG_LAN91C96
Support for SMSC's LAN91C96 chips.
CONFIG_LAN91C96_BASE
Define this to hold the physical address
of the LAN91C96's I/O space
CONFIG_LAN91C96_USE_32_BIT
Define this to enable 32 bit addressing
CONFIG_SMC91111
Support for SMSC's LAN91C111 chip
CONFIG_SMC91111_BASE
Define this to hold the physical address
of the device (I/O space)
CONFIG_SMC_USE_32_BIT
Define this if data bus is 32 bits
CONFIG_SMC_USE_IOFUNCS
Define this to use i/o functions instead of macros
(some hardware wont work with macros)
CONFIG_DRIVER_TI_EMAC
Support for davinci emac
CONFIG_SYS_DAVINCI_EMAC_PHY_COUNT
Define this if you have more then 3 PHYs.
CONFIG_FTGMAC100
Support for Faraday's FTGMAC100 Gigabit SoC Ethernet
CONFIG_FTGMAC100_EGIGA
Define this to use GE link update with gigabit PHY.
Define this if FTGMAC100 is connected to gigabit PHY.
If your system has 10/100 PHY only, it might not occur
wrong behavior. Because PHY usually return timeout or
useless data when polling gigabit status and gigabit
control registers. This behavior won't affect the
correctnessof 10/100 link speed update.
CONFIG_SMC911X
Support for SMSC's LAN911x and LAN921x chips
CONFIG_SMC911X_BASE
Define this to hold the physical address
of the device (I/O space)
CONFIG_SMC911X_32_BIT
Define this if data bus is 32 bits
CONFIG_SMC911X_16_BIT
Define this if data bus is 16 bits. If your processor
automatically converts one 32 bit word to two 16 bit
words you may also try CONFIG_SMC911X_32_BIT.
CONFIG_SH_ETHER
Support for Renesas on-chip Ethernet controller
CONFIG_SH_ETHER_USE_PORT
Define the number of ports to be used
CONFIG_SH_ETHER_PHY_ADDR
Define the ETH PHY's address
CONFIG_SH_ETHER_CACHE_WRITEBACK
If this option is set, the driver enables cache flush.PWM Support: CONFIG_PWM_IMX Support for PWM modul on the imx6.
TPM Support: CONFIG_TPM Support TPM devices.
CONFIG_TPM_TIS_I2C
Support for i2c bus TPM devices. Only one device
per system is supported at this time.
CONFIG_TPM_TIS_I2C_BUS_NUMBER
Define the the i2c bus number for the TPM device
CONFIG_TPM_TIS_I2C_SLAVE_ADDRESS
Define the TPM's address on the i2c bus
CONFIG_TPM_TIS_I2C_BURST_LIMITATION
Define the burst count bytes upper limit
CONFIG_TPM_ATMEL_TWI
Support for Atmel TWI TPM device. Requires I2C support.
CONFIG_TPM_TIS_LPC
Support for generic parallel port TPM devices. Only one device
per system is supported at this time.
CONFIG_TPM_TIS_BASE_ADDRESS
Base address where the generic TPM device is mapped
to. Contemporary x86 systems usually map it at
0xfed40000.
CONFIG_CMD_TPM
Add tpm monitor functions.
Requires CONFIG_TPM. If CONFIG_TPM_AUTH_SESSIONS is set, also
provides monitor access to authorized functions.
CONFIG_TPM
Define this to enable the TPM support library which provides
functional interfaces to some TPM commands.
Requires support for a TPM device.
CONFIG_TPM_AUTH_SESSIONS
Define this to enable authorized functions in the TPM library.
Requires CONFIG_TPM and CONFIG_SHA1.USB Support: At the moment only the UHCI host controller is supported (PIP405, MIP405, MPC5200); define CONFIG_USB_UHCI to enable it. define CONFIG_USB_KEYBOARD to enable the USB Keyboard and define CONFIG_USB_STORAGE to enable the USB storage devices. Note: Supported are USB Keyboards and USB Floppy drives (TEAC FD-05PUB). MPC5200 USB requires additional defines: CONFIG_USB_CLOCK for 528 MHz Clock: 0x0001bbbb CONFIG_PSC3_USB for USB on PSC3 CONFIG_USB_CONFIG for differential drivers: 0x00001000 for single ended drivers: 0x00005000 for differential drivers on PSC3: 0x00000100 for single ended drivers on PSC3: 0x00004100 CONFIG_SYS_USB_EVENT_POLL May be defined to allow interrupt polling instead of using asynchronous interrupts
CONFIG_USB_EHCI_TXFIFO_THRESH enables setting of the
txfilltuning field in the EHCI controller on reset.
CONFIG_USB_DWC2_REG_ADDR the physical CPU address of the DWC2
HW module registers.USB Device: Define the below if you wish to use the USB console. Once firmware is rebuilt from a serial console issue the command "setenv stdin usbtty; setenv stdout usbtty" and attach your USB cable. The Unix command "dmesg" should print it has found a new device. The environment variable usbtty can be set to gserial or cdc_acm to enable your device to appear to a USB host as a Linux gserial device or a Common Device Class Abstract Control Model serial device. If you select usbtty = gserial you should be able to enumerate a Linux host by
else if using cdc_acm, simply setting the environment
variable usbtty to be cdc_acm should suffice. The following
might be defined in YourBoardName.h
CONFIG_USB_DEVICE
Define this to build a UDC device
CONFIG_USB_TTY
Define this to have a tty type of device available to
talk to the UDC device
CONFIG_USBD_HS
Define this to enable the high speed support for usb
device and usbtty. If this feature is enabled, a routine
int is_usbd_high_speed(void)
also needs to be defined by the driver to dynamically poll
whether the enumeration has succeded at high speed or full
speed.
CONFIG_SYS_CONSOLE_IS_IN_ENV
Define this if you want stdin, stdout &/or stderr to
be set to usbtty.
mpc8xx:
CONFIG_SYS_USB_EXTC_CLK 0xBLAH
Derive USB clock from external clock "blah"
- CONFIG_SYS_USB_EXTC_CLK 0x02
CONFIG_SYS_USB_BRG_CLK 0xBLAH
Derive USB clock from brgclk
- CONFIG_SYS_USB_BRG_CLK 0x04
If you have a USB-IF assigned VendorID then you may wish to
define your own vendor specific values either in BoardName.h
or directly in usbd_vendor_info.h. If you don't define
CONFIG_USBD_MANUFACTURER, CONFIG_USBD_PRODUCT_NAME,
CONFIG_USBD_VENDORID and CONFIG_USBD_PRODUCTID, then U-Boot
should pretend to be a Linux device to it's target host.
CONFIG_USBD_MANUFACTURER
Define this string as the name of your company for
- CONFIG_USBD_MANUFACTURER "my company"
CONFIG_USBD_PRODUCT_NAME
Define this string as the name of your product
- CONFIG_USBD_PRODUCT_NAME "acme usb device"
CONFIG_USBD_VENDORID
Define this as your assigned Vendor ID from the USB
Implementors Forum. This *must* be a genuine Vendor ID
to avoid polluting the USB namespace.
- CONFIG_USBD_VENDORID 0xFFFF
CONFIG_USBD_PRODUCTID
Define this as the unique Product ID
for your device
- CONFIG_USBD_PRODUCTID 0xFFFFULPI Layer Support: The ULPI (UTMI Low Pin (count) Interface) PHYs are supported via the generic ULPI layer. The generic layer accesses the ULPI PHY via the platform viewport, so you need both the genric layer and the viewport enabled. Currently only Chipidea/ARC based viewport is supported. To enable the ULPI layer support, define CONFIG_USB_ULPI and CONFIG_USB_ULPI_VIEWPORT in your board configuration file. If your ULPI phy needs a different reference clock than the standard 24 MHz then you have to define CONFIG_ULPI_REF_CLK to the appropriate value in Hz.
MMC Support: The MMC controller on the Intel PXA is supported. To enable this define CONFIG_MMC. The MMC can be accessed from the boot prompt by mapping the device to physical memory similar to flash. Command line is enabled with CONFIG_CMD_MMC. The MMC driver also works with the FAT fs. This is enabled with CONFIG_CMD_FAT.
CONFIG_SH_MMCIF
Support for Renesas on-chip MMCIF controller
CONFIG_SH_MMCIF_ADDR
Define the base address of MMCIF registers
CONFIG_SH_MMCIF_CLK
Define the clock frequency for MMCIF
CONFIG_GENERIC_MMC
Enable the generic MMC driver
CONFIG_SUPPORT_EMMC_BOOT
Enable some additional features of the eMMC boot partitions.
CONFIG_SUPPORT_EMMC_RPMB
Enable the commands for reading, writing and programming the
key for the Replay Protection Memory Block partition in eMMC.USB Device Firmware Update (DFU) class support: CONFIG_DFU_FUNCTION This enables the USB portion of the DFU USB class
CONFIG_CMD_DFU
This enables the command "dfu" which is used to have
U-Boot create a DFU class device via USB. This command
requires that the "dfu_alt_info" environment variable be
set and define the alt settings to expose to the host.
CONFIG_DFU_MMC
This enables support for exposing (e)MMC devices via DFU.
CONFIG_DFU_NAND
This enables support for exposing NAND devices via DFU.
CONFIG_DFU_RAM
This enables support for exposing RAM via DFU.
Note: DFU spec refer to non-volatile memory usage, but
allow usages beyond the scope of spec - here RAM usage,
one that would help mostly the developer.
CONFIG_SYS_DFU_DATA_BUF_SIZE
Dfu transfer uses a buffer before writing data to the
raw storage device. Make the size (in bytes) of this buffer
configurable. The size of this buffer is also configurable
through the "dfu_bufsiz" environment variable.
CONFIG_SYS_DFU_MAX_FILE_SIZE
When updating files rather than the raw storage device,
we use a static buffer to copy the file into and then write
the buffer once we've been given the whole file. Define
this to the maximum filesize (in bytes) for the buffer.
Default is 4 MiB if undefined.
DFU_DEFAULT_POLL_TIMEOUT
Poll timeout [ms], is the timeout a device can send to the
host. The host must wait for this timeout before sending
a subsequent DFU_GET_STATUS request to the device.
DFU_MANIFEST_POLL_TIMEOUT
Poll timeout [ms], which the device sends to the host when
entering dfuMANIFEST state. Host waits this timeout, before
sending again an USB request to the device.USB Device Android Fastboot support: CONFIG_CMD_FASTBOOT This enables the command "fastboot" which enables the Android fastboot mode for the platform's USB device. Fastboot is a USB protocol for downloading images, flashing and device control used on Android devices. See doc/README.android-fastboot for more information.
CONFIG_ANDROID_BOOT_IMAGE
This enables support for booting images which use the Android
image format header.
CONFIG_USB_FASTBOOT_BUF_ADDR
The fastboot protocol requires a large memory buffer for
downloads. Define this to the starting RAM address to use for
downloaded images.
CONFIG_USB_FASTBOOT_BUF_SIZE
The fastboot protocol requires a large memory buffer for
downloads. This buffer should be as large as possible for a
platform. Define this to the size available RAM for fastboot.
CONFIG_FASTBOOT_FLASH
The fastboot protocol includes a "flash" command for writing
the downloaded image to a non-volatile storage device. Define
this to enable the "fastboot flash" command.
CONFIG_FASTBOOT_FLASH_MMC_DEV
The fastboot "flash" command requires additional information
regarding the non-volatile storage device. Define this to
the eMMC device that fastboot should use to store the image.
CONFIG_FASTBOOT_GPT_NAME
The fastboot "flash" command supports writing the downloaded
image to the Protective MBR and the Primary GUID Partition
Table. (Additionally, this downloaded image is post-processed
to generate and write the Backup GUID Partition Table.)
This occurs when the specified "partition name" on the
"fastboot flash" command line matches this value.
Default is GPT_ENTRY_NAME (currently "gpt") if undefined.Journaling Flash filesystem support: CONFIG_JFFS2_NAND, CONFIG_JFFS2_NAND_OFF, CONFIG_JFFS2_NAND_SIZE, CONFIG_JFFS2_NAND_DEV Define these for a default partition on a NAND device
CONFIG_SYS_JFFS2_FIRST_SECTOR,
CONFIG_SYS_JFFS2_FIRST_BANK, CONFIG_SYS_JFFS2_NUM_BANKS
Define these for a default partition on a NOR device
CONFIG_SYS_JFFS_CUSTOM_PART
Define this to create an own partition. You have to provide a
function struct part_info* jffs2_part_info(int part_num)
If you define only one JFFS2 partition you may also want to
#define CONFIG_SYS_JFFS_SINGLE_PART 1
to disable the command chpart. This is the default when you
have not defined a custom partitionFAT(File Allocation Table) filesystem write function support: CONFIG_FAT_WRITE
Define this to enable support for saving memory data as a
file in FAT formatted partition.
This will also enable the command "fatwrite" enabling the
user to write files to FAT.CBFS (Coreboot Filesystem) support CONFIG_CMD_CBFS
Define this to enable support for reading from a Coreboot
filesystem. Available commands are cbfsinit, cbfsinfo, cbfsls
and cbfsload.FAT(File Allocation Table) filesystem cluster size: CONFIG_FS_FAT_MAX_CLUSTSIZE
Define the max cluster size for fat operations else
a default value of 65536 will be defined.Keyboard Support: CONFIG_ISA_KEYBOARD
Define this to enable standard (PC-Style) keyboard
support
CONFIG_I8042_KBD
Standard PC keyboard driver with US (is default) and
GERMAN key layout (switch via environment 'keymap=de') support.
Export function i8042_kbd_init, i8042_tstc and i8042_getc
for cfb_console. Supports cursor blinking.
CONFIG_CROS_EC_KEYB
Enables a Chrome OS keyboard using the CROS_EC interface.
This uses CROS_EC to communicate with a second microcontroller
which provides key scans on request.Video support: CONFIG_VIDEO
Define this to enable video support (for output to
video).
CONFIG_VIDEO_CT69000
Enable Chips & Technologies 69000 Video chip
CONFIG_VIDEO_SMI_LYNXEM
Enable Silicon Motion SMI 712/710/810 Video chip. The
video output is selected via environment 'videoout'
(1 = LCD and 2 = CRT). If videoout is undefined, CRT is
assumed.
For the CT69000 and SMI_LYNXEM drivers, videomode is
selected via environment 'videomode'. Two different ways
are possible:
- "videomode=num" 'num' is a standard LiLo mode numbers.
Following standard modes are supported (* is default):
Colors 640x480 800x600 1024x768 1152x864 1280x1024
-------------+---------------------------------------------
8 bits | 0x301* 0x303 0x305 0x161 0x307
15 bits | 0x310 0x313 0x316 0x162 0x319
16 bits | 0x311 0x314 0x317 0x163 0x31A
24 bits | 0x312 0x315 0x318 ? 0x31B
-------------+---------------------------------------------
(i.e. setenv videomode 317; saveenv; reset;)
- "videomode=bootargs" all the video parameters are parsed
from the bootargs. (See drivers/video/videomodes.c)
CONFIG_VIDEO_SED13806
Enable Epson SED13806 driver. This driver supports 8bpp
and 16bpp modes defined by CONFIG_VIDEO_SED13806_8BPP
or CONFIG_VIDEO_SED13806_16BPP
CONFIG_FSL_DIU_FB
Enable the Freescale DIU video driver. Reference boards for
SOCs that have a DIU should define this macro to enable DIU
support, and should also define these other macros:
CONFIG_SYS_DIU_ADDR
CONFIG_VIDEO
CONFIG_CMD_BMP
CONFIG_CFB_CONSOLE
CONFIG_VIDEO_SW_CURSOR
CONFIG_VGA_AS_SINGLE_DEVICE
CONFIG_VIDEO_LOGO
CONFIG_VIDEO_BMP_LOGO
The DIU driver will look for the 'video-mode' environment
variable, and if defined, enable the DIU as a console during
boot. See the documentation file README.video for a
description of this variable.Keyboard Support: CONFIG_KEYBOARD
Define this to enable a custom keyboard support.
This simply calls drv_keyboard_init() which must be
defined in your board-specific files.
The only board using this so far is RBC823.LCD Support: CONFIG_LCD
Define this to enable LCD support (for output to LCD
display); also select one of the supported displays
by defining one of these:
CONFIG_ATMEL_LCD:
HITACHI TX09D70VM1CCA, 3.5", 240x320.
CONFIG_NEC_NL6448AC33:
NEC NL6448AC33-18. Active, color, single scan.
CONFIG_NEC_NL6448BC20
NEC NL6448BC20-08. 6.5", 640x480.
Active, color, single scan.
CONFIG_NEC_NL6448BC33_54
NEC NL6448BC33-54. 10.4", 640x480.
Active, color, single scan.
CONFIG_SHARP_16x9
Sharp 320x240. Active, color, single scan.
It isn't 16x9, and I am not sure what it is.
CONFIG_SHARP_LQ64D341
Sharp LQ64D341 display, 640x480.
Active, color, single scan.
CONFIG_HLD1045
HLD1045 display, 640x480.
Active, color, single scan.
CONFIG_OPTREX_BW
Optrex CBL50840-2 NF-FW 99 22 M5
or
Hitachi LMG6912RPFC-00T
or
Hitachi SP14Q002
320x240. Black & white.
Normally display is black on white background; define
CONFIG_SYS_WHITE_ON_BLACK to get it inverted.
CONFIG_LCD_ALIGNMENT
Normally the LCD is page-aligned (typically 4KB). If this is
defined then the LCD will be aligned to this value instead.
For ARM it is sometimes useful to use MMU_SECTION_SIZE
here, since it is cheaper to change data cache settings on
a per-section basis.
CONFIG_CONSOLE_SCROLL_LINES
When the console need to be scrolled, this is the number of
lines to scroll by. It defaults to 1. Increasing this makes
the console jump but can help speed up operation when scrolling
is slow.
CONFIG_LCD_ROTATION
Sometimes, for example if the display is mounted in portrait
mode or even if it's mounted landscape but rotated by 180degree,
we need to rotate our content of the display relative to the
framebuffer, so that user can read the messages which are
printed out.
Once CONFIG_LCD_ROTATION is defined, the lcd_console will be
initialized with a given rotation from "vl_rot" out of
"vidinfo_t" which is provided by the board specific code.
The value for vl_rot is coded as following (matching to
fbcon=rotate:<n> linux-kernel commandline):
0 = no rotation respectively 0 degree
1 = 90 degree rotation
2 = 180 degree rotation
3 = 270 degree rotation
If CONFIG_LCD_ROTATION is not defined, the console will be
initialized with 0degree rotation.
CONFIG_LCD_BMP_RLE8
Support drawing of RLE8-compressed bitmaps on the LCD.
CONFIG_I2C_EDID
Enables an 'i2c edid' command which can read EDID
information over I2C from an attached LCD display.Splash Screen Support: CONFIG_SPLASH_SCREEN
If this option is set, the environment is checked for
a variable "splashimage". If found, the usual display
of logo, copyright and system information on the LCD
is suppressed and the BMP image at the address
specified in "splashimage" is loaded instead. The
console is redirected to the "nulldev", too. This
allows for a "silent" boot where a splash screen is
loaded very quickly after power-on.
CONFIG_SPLASHIMAGE_GUARD
If this option is set, then U-Boot will prevent the environment
variable "splashimage" from being set to a problematic address
(see README.displaying-bmps).
This option is useful for targets where, due to alignment
restrictions, an improperly aligned BMP image will cause a data
abort. If you think you will not have problems with unaligned
accesses (for example because your toolchain prevents them)
there is no need to set this option.
CONFIG_SPLASH_SCREEN_ALIGN
If this option is set the splash image can be freely positioned
on the screen. Environment variable "splashpos" specifies the
position as "x,y". If a positive number is given it is used as
number of pixel from left/top. If a negative number is given it
is used as number of pixel from right/bottom. You can also
specify 'm' for centering the image.
Example:
setenv splashpos m,m
=> image at center of screen
setenv splashpos 30,20
=> image at x = 30 and y = 20
setenv splashpos -10,m
=> vertically centered image
at x = dspWidth - bmpWidth - 9Gzip compressed BMP image support: CONFIG_VIDEO_BMP_GZIP
If this option is set, additionally to standard BMP
images, gzipped BMP images can be displayed via the
splashscreen support or the bmp command.Run length encoded BMP image (RLE8) support: CONFIG_VIDEO_BMP_RLE8
If this option is set, 8-bit RLE compressed BMP images
can be displayed via the splashscreen support or the
bmp command.Do compressing for memory range: CONFIG_CMD_ZIP
If this option is set, it would use zlib deflate method
to compress the specified memory at its best effort.Compression support: CONFIG_GZIP
Enabled by default to support gzip compressed images.
CONFIG_BZIP2
If this option is set, support for bzip2 compressed
images is included. If not, only uncompressed and gzip
compressed images are supported.
NOTE: the bzip2 algorithm requires a lot of RAM, so
the malloc area (as defined by CONFIG_SYS_MALLOC_LEN) should
be at least 4MB.
CONFIG_LZMA
If this option is set, support for lzma compressed
images is included.
Note: The LZMA algorithm adds between 2 and 4KB of code and it
requires an amount of dynamic memory that is given by the
formula:
(1846 + 768 << (lc + lp)) * sizeof(uint16)
Where lc and lp stand for, respectively, Literal context bits
and Literal pos bits.
This value is upper-bounded by 14MB in the worst case. Anyway,
for a ~4MB large kernel image, we have lc=3 and lp=0 for a
total amount of (1846 + 768 << (3 + 0)) * 2 = ~41KB... that is
a very small buffer.
Use the lzmainfo tool to determinate the lc and lp values and
then calculate the amount of needed dynamic memory (ensuring
the appropriate CONFIG_SYS_MALLOC_LEN value).
CONFIG_LZO
If this option is set, support for LZO compressed images
is included.MII/PHY support: CONFIG_PHY_ADDR
The address of PHY on MII bus.
CONFIG_PHY_CLOCK_FREQ (ppc4xx)
The clock frequency of the MII bus
CONFIG_PHY_GIGE
If this option is set, support for speed/duplex
detection of gigabit PHY is included.
CONFIG_PHY_RESET_DELAY
Some PHY like Intel LXT971A need extra delay after
reset before any MII register access is possible.
For such PHY, set this option to the usec delay
required. (minimum 300usec for LXT971A)
CONFIG_PHY_CMD_DELAY (ppc4xx)
Some PHY like Intel LXT971A need extra delay after
command issued before MII status register can be readIP address: CONFIG_IPADDR
Define a default value for the IP address to use for
the default Ethernet interface, in case this is not
determined through e.g. bootp.
(Environment variable "ipaddr")Server IP address: CONFIG_SERVERIP
Defines a default value for the IP address of a TFTP
server to contact when using the "tftboot" command.
(Environment variable "serverip")
CONFIG_KEEP_SERVERADDR
Keeps the server's MAC address, in the env 'serveraddr'
for passing to bootargs (like Linux's netconsole option)Gateway IP address: CONFIG_GATEWAYIP
Defines a default value for the IP address of the
default router where packets to other networks are
sent to.
(Environment variable "gatewayip")Subnet mask: CONFIG_NETMASK
Defines a default value for the subnet mask (or
routing prefix) which is used to determine if an IP
address belongs to the local subnet or needs to be
forwarded through a router.
(Environment variable "netmask")Multicast TFTP Mode: CONFIG_MCAST_TFTP
Defines whether you want to support multicast TFTP as per
rfc-2090; for example to work with atftp. Lets lots of targets
tftp down the same boot image concurrently. Note: the Ethernet
driver in use must provide a function: mcast() to join/leave a
multicast group.BOOTP Recovery Mode: CONFIG_BOOTP_RANDOM_DELAY
If you have many targets in a network that try to
boot using BOOTP, you may want to avoid that all
systems send out BOOTP requests at precisely the same
moment (which would happen for instance at recovery
from a power failure, when all systems will try to
boot, thus flooding the BOOTP server. Defining
CONFIG_BOOTP_RANDOM_DELAY causes a random delay to be
inserted before sending out BOOTP requests. The
following delays are inserted then:
1st BOOTP request: delay 0 ... 1 sec
2nd BOOTP request: delay 0 ... 2 sec
3rd BOOTP request: delay 0 ... 4 sec
4th and following
BOOTP requests: delay 0 ... 8 sec
CONFIG_BOOTP_ID_CACHE_SIZE
BOOTP packets are uniquely identified using a 32-bit ID. The
server will copy the ID from client requests to responses and
U-Boot will use this to determine if it is the destination of
an incoming response. Some servers will check that addresses
aren't in use before handing them out (usually using an ARP
ping) and therefore take up to a few hundred milliseconds to
respond. Network congestion may also influence the time it
takes for a response to make it back to the client. If that
time is too long, U-Boot will retransmit requests. In order
to allow earlier responses to still be accepted after these
retransmissions, U-Boot's BOOTP client keeps a small cache of
IDs. The CONFIG_BOOTP_ID_CACHE_SIZE controls the size of this
cache. The default is to keep IDs for up to four outstanding
requests. Increasing this will allow U-Boot to accept offers
from a BOOTP client in networks with unusually high latency.DHCP Advanced Options: You can fine tune the DHCP functionality by defining CONFIGBOOTP* symbols:
CONFIG_BOOTP_SUBNETMASK
CONFIG_BOOTP_GATEWAY
CONFIG_BOOTP_HOSTNAME
CONFIG_BOOTP_NISDOMAIN
CONFIG_BOOTP_BOOTPATH
CONFIG_BOOTP_BOOTFILESIZE
CONFIG_BOOTP_DNS
CONFIG_BOOTP_DNS2
CONFIG_BOOTP_SEND_HOSTNAME
CONFIG_BOOTP_NTPSERVER
CONFIG_BOOTP_TIMEOFFSET
CONFIG_BOOTP_VENDOREX
CONFIG_BOOTP_MAY_FAIL
CONFIG_BOOTP_SERVERIP - TFTP server will be the serverip
environment variable, not the BOOTP server.
CONFIG_BOOTP_MAY_FAIL - If the DHCP server is not found
after the configured retry count, the call will fail
instead of starting over. This can be used to fail over
to Link-local IP address configuration if the DHCP server
is not available.
CONFIG_BOOTP_DNS2 - If a DHCP client requests the DNS
serverip from a DHCP server, it is possible that more
than one DNS serverip is offered to the client.
If CONFIG_BOOTP_DNS2 is enabled, the secondary DNS
serverip will be stored in the additional environment
variable "dnsip2". The first DNS serverip is always
stored in the variable "dnsip", when CONFIG_BOOTP_DNS
is defined.
CONFIG_BOOTP_SEND_HOSTNAME - Some DHCP servers are capable
to do a dynamic update of a DNS server. To do this, they
need the hostname of the DHCP requester.
If CONFIG_BOOTP_SEND_HOSTNAME is defined, the content
of the "hostname" environment variable is passed as
option 12 to the DHCP server.
CONFIG_BOOTP_DHCP_REQUEST_DELAY
A 32bit value in microseconds for a delay between
receiving a "DHCP Offer" and sending the "DHCP Request".
This fixes a problem with certain DHCP servers that don't
respond 100% of the time to a "DHCP request". E.g. On an
AT91RM9200 processor running at 180MHz, this delay needed
to be *at least* 15,000 usec before a Windows Server 2003
DHCP server would reply 100% of the time. I recommend at
least 50,000 usec to be safe. The alternative is to hope
that one of the retries will be successful but note that
the DHCP timeout and retry process takes a longer than
this delay.Link-local IP address negotiation: Negotiate with other link-local clients on the local network for an address that doesn't require explicit configuration. This is especially useful if a DHCP server cannot be guaranteed to exist in all environments that the device must operate.
See doc/README.link-local for more information.
CDP Options: CONFIG_CDP_DEVICE_ID
The device id used in CDP trigger frames.
CONFIG_CDP_DEVICE_ID_PREFIX
A two character string which is prefixed to the MAC address of the device.
CONFIG_CDP_PORT_ID
A printf format string which contains the ascii name of the port. Normally is set to "eth%d" which sets eth0 for the first Ethernet, eth1 for the second etc.
CONFIG_CDP_CAPABILITIES
A 32bit integer which indicates the device capabilities; 0x00000010 for a normal host which does not forwards.
CONFIG_CDP_VERSION
An ascii string containing the version of the software.
CONFIG_CDP_PLATFORM
An ascii string containing the name of the platform.
CONFIG_CDP_TRIGGER
A 32bit integer sent on the trigger.
CONFIG_CDP_POWER_CONSUMPTION
A 16bit integer containing the power consumption of the device in .1 of milliwatts.
CONFIG_CDP_APPLIANCE_VLAN_TYPE
A byte containing the id of the VLAN.
Status LED: CONFIG_STATUS_LED
Several configurations allow to display the current
status using a LED. For instance, the LED will blink
fast while running U-Boot code, stop blinking as
soon as a reply to a BOOTP request was received, and
start blinking slow once the Linux kernel is running
(supported by a status LED driver in the Linux
kernel). Defining CONFIG_STATUS_LED enables this
feature in U-Boot.
Additional options:
CONFIG_GPIO_LED
The status LED can be connected to a GPIO pin.
In such cases, the gpio_led driver can be used as a
status LED backend implementation. Define CONFIG_GPIO_LED
to include the gpio_led driver in the U-Boot binary.
CONFIG_GPIO_LED_INVERTED_TABLE
Some GPIO connected LEDs may have inverted polarity in which
case the GPIO high value corresponds to LED off state and
GPIO low value corresponds to LED on state.
In such cases CONFIG_GPIO_LED_INVERTED_TABLE may be defined
with a list of GPIO LEDs that have inverted polarity.CAN Support: CONFIG_CAN_DRIVER
Defining CONFIG_CAN_DRIVER enables CAN driver support
on those systems that support this (optional)
feature, like the TQM8xxL modules.I2C Support: CONFIG_SYS_I2C
This enable the NEW i2c subsystem, and will allow you to use
i2c commands at the u-boot command line (as long as you set
CONFIG_CMD_I2C in CONFIG_COMMANDS) and communicate with i2c
based realtime clock chips or other i2c devices. See
common/cmd_i2c.c for a description of the command line
interface.
ported i2c driver to the new framework:
- drivers/i2c/soft_i2c.c:
- activate first bus with CONFIG_SYS_I2C_SOFT define
CONFIG_SYS_I2C_SOFT_SPEED and CONFIG_SYS_I2C_SOFT_SLAVE
for defining speed and slave address
- activate second bus with I2C_SOFT_DECLARATIONS2 define
CONFIG_SYS_I2C_SOFT_SPEED_2 and CONFIG_SYS_I2C_SOFT_SLAVE_2
for defining speed and slave address
- activate third bus with I2C_SOFT_DECLARATIONS3 define
CONFIG_SYS_I2C_SOFT_SPEED_3 and CONFIG_SYS_I2C_SOFT_SLAVE_3
for defining speed and slave address
- activate fourth bus with I2C_SOFT_DECLARATIONS4 define
CONFIG_SYS_I2C_SOFT_SPEED_4 and CONFIG_SYS_I2C_SOFT_SLAVE_4
for defining speed and slave address
- drivers/i2c/fsl_i2c.c:
- activate i2c driver with CONFIG_SYS_I2C_FSL
define CONFIG_SYS_FSL_I2C_OFFSET for setting the register
offset CONFIG_SYS_FSL_I2C_SPEED for the i2c speed and
CONFIG_SYS_FSL_I2C_SLAVE for the slave addr of the first
bus.
- If your board supports a second fsl i2c bus, define
CONFIG_SYS_FSL_I2C2_OFFSET for the register offset
CONFIG_SYS_FSL_I2C2_SPEED for the speed and
CONFIG_SYS_FSL_I2C2_SLAVE for the slave address of the
second bus.
- drivers/i2c/tegra_i2c.c:
- activate this driver with CONFIG_SYS_I2C_TEGRA
- This driver adds 4 i2c buses with a fix speed from
100000 and the slave addr 0!
- drivers/i2c/ppc4xx_i2c.c
- activate this driver with CONFIG_SYS_I2C_PPC4XX
- CONFIG_SYS_I2C_PPC4XX_CH0 activate hardware channel 0
- CONFIG_SYS_I2C_PPC4XX_CH1 activate hardware channel 1
- drivers/i2c/i2c_mxc.c
- activate this driver with CONFIG_SYS_I2C_MXC
- define speed for bus 1 with CONFIG_SYS_MXC_I2C1_SPEED
- define slave for bus 1 with CONFIG_SYS_MXC_I2C1_SLAVE
- define speed for bus 2 with CONFIG_SYS_MXC_I2C2_SPEED
- define slave for bus 2 with CONFIG_SYS_MXC_I2C2_SLAVE
- define speed for bus 3 with CONFIG_SYS_MXC_I2C3_SPEED
- define slave for bus 3 with CONFIG_SYS_MXC_I2C3_SLAVE
If those defines are not set, default value is 100000
for speed, and 0 for slave.
- enable bus 3 with CONFIG_SYS_I2C_MXC_I2C3
- enable bus 4 with CONFIG_SYS_I2C_MXC_I2C4
- drivers/i2c/rcar_i2c.c:
- activate this driver with CONFIG_SYS_I2C_RCAR
- This driver adds 4 i2c buses
- CONFIG_SYS_RCAR_I2C0_BASE for setting the register channel 0
- CONFIG_SYS_RCAR_I2C0_SPEED for for the speed channel 0
- CONFIG_SYS_RCAR_I2C1_BASE for setting the register channel 1
- CONFIG_SYS_RCAR_I2C1_SPEED for for the speed channel 1
- CONFIG_SYS_RCAR_I2C2_BASE for setting the register channel 2
- CONFIG_SYS_RCAR_I2C2_SPEED for for the speed channel 2
- CONFIG_SYS_RCAR_I2C3_BASE for setting the register channel 3
- CONFIG_SYS_RCAR_I2C3_SPEED for for the speed channel 3
- CONFIF_SYS_RCAR_I2C_NUM_CONTROLLERS for number of i2c buses
- drivers/i2c/sh_i2c.c:
- activate this driver with CONFIG_SYS_I2C_SH
- This driver adds from 2 to 5 i2c buses
- CONFIG_SYS_I2C_SH_BASE0 for setting the register channel 0
- CONFIG_SYS_I2C_SH_SPEED0 for for the speed channel 0
- CONFIG_SYS_I2C_SH_BASE1 for setting the register channel 1
- CONFIG_SYS_I2C_SH_SPEED1 for for the speed channel 1
- CONFIG_SYS_I2C_SH_BASE2 for setting the register channel 2
- CONFIG_SYS_I2C_SH_SPEED2 for for the speed channel 2
- CONFIG_SYS_I2C_SH_BASE3 for setting the register channel 3
- CONFIG_SYS_I2C_SH_SPEED3 for for the speed channel 3
- CONFIG_SYS_I2C_SH_BASE4 for setting the register channel 4
- CONFIG_SYS_I2C_SH_SPEED4 for for the speed channel 4
- CONFIG_SYS_I2C_SH_BASE5 for setting the register channel 5
- CONFIG_SYS_I2C_SH_SPEED5 for for the speed channel 5
- CONFIG_SYS_I2C_SH_NUM_CONTROLLERS for number of i2c buses
- drivers/i2c/omap24xx_i2c.c
- activate this driver with CONFIG_SYS_I2C_OMAP24XX
- CONFIG_SYS_OMAP24_I2C_SPEED speed channel 0
- CONFIG_SYS_OMAP24_I2C_SLAVE slave addr channel 0
- CONFIG_SYS_OMAP24_I2C_SPEED1 speed channel 1
- CONFIG_SYS_OMAP24_I2C_SLAVE1 slave addr channel 1
- CONFIG_SYS_OMAP24_I2C_SPEED2 speed channel 2
- CONFIG_SYS_OMAP24_I2C_SLAVE2 slave addr channel 2
- CONFIG_SYS_OMAP24_I2C_SPEED3 speed channel 3
- CONFIG_SYS_OMAP24_I2C_SLAVE3 slave addr channel 3
- CONFIG_SYS_OMAP24_I2C_SPEED4 speed channel 4
- CONFIG_SYS_OMAP24_I2C_SLAVE4 slave addr channel 4
- drivers/i2c/zynq_i2c.c
- activate this driver with CONFIG_SYS_I2C_ZYNQ
- set CONFIG_SYS_I2C_ZYNQ_SPEED for speed setting
- set CONFIG_SYS_I2C_ZYNQ_SLAVE for slave addr
- drivers/i2c/s3c24x0_i2c.c:
- activate this driver with CONFIG_SYS_I2C_S3C24X0
- This driver adds i2c buses (11 for Exynos5250, Exynos5420
9 i2c buses for Exynos4 and 1 for S3C24X0 SoCs from Samsung)
with a fix speed from 100000 and the slave addr 0!
- drivers/i2c/ihs_i2c.c
- activate this driver with CONFIG_SYS_I2C_IHS
- CONFIG_SYS_I2C_IHS_CH0 activate hardware channel 0
- CONFIG_SYS_I2C_IHS_SPEED_0 speed channel 0
- CONFIG_SYS_I2C_IHS_SLAVE_0 slave addr channel 0
- CONFIG_SYS_I2C_IHS_CH1 activate hardware channel 1
- CONFIG_SYS_I2C_IHS_SPEED_1 speed channel 1
- CONFIG_SYS_I2C_IHS_SLAVE_1 slave addr channel 1
- CONFIG_SYS_I2C_IHS_CH2 activate hardware channel 2
- CONFIG_SYS_I2C_IHS_SPEED_2 speed channel 2
- CONFIG_SYS_I2C_IHS_SLAVE_2 slave addr channel 2
- CONFIG_SYS_I2C_IHS_CH3 activate hardware channel 3
- CONFIG_SYS_I2C_IHS_SPEED_3 speed channel 3
- CONFIG_SYS_I2C_IHS_SLAVE_3 slave addr channel 3
additional defines:
CONFIG_SYS_NUM_I2C_BUSES
Hold the number of i2c buses you want to use. If you
don't use/have i2c muxes on your i2c bus, this
is equal to CONFIG_SYS_NUM_I2C_ADAPTERS, and you can
omit this define.
CONFIG_SYS_I2C_DIRECT_BUS
define this, if you don't use i2c muxes on your hardware.
if CONFIG_SYS_I2C_MAX_HOPS is not defined or == 0 you can
omit this define.
CONFIG_SYS_I2C_MAX_HOPS
define how many muxes are maximal consecutively connected
on one i2c bus. If you not use i2c muxes, omit this
define.
CONFIG_SYS_I2C_BUSES
hold a list of buses you want to use, only used if
CONFIG_SYS_I2C_DIRECT_BUS is not defined, for example
a board with CONFIG_SYS_I2C_MAX_HOPS = 1 and
CONFIG_SYS_NUM_I2C_BUSES = 9:
CONFIG_SYS_I2C_BUSES {{0, {I2C_NULL_HOP}}, \
{0, {{I2C_MUX_PCA9547, 0x70, 1}}}, \
{0, {{I2C_MUX_PCA9547, 0x70, 2}}}, \
{0, {{I2C_MUX_PCA9547, 0x70, 3}}}, \
{0, {{I2C_MUX_PCA9547, 0x70, 4}}}, \
{0, {{I2C_MUX_PCA9547, 0x70, 5}}}, \
{1, {I2C_NULL_HOP}}, \
{1, {{I2C_MUX_PCA9544, 0x72, 1}}}, \
{1, {{I2C_MUX_PCA9544, 0x72, 2}}}, \
}
which defines
bus 0 on adapter 0 without a mux
bus 1 on adapter 0 with a PCA9547 on address 0x70 port 1
bus 2 on adapter 0 with a PCA9547 on address 0x70 port 2
bus 3 on adapter 0 with a PCA9547 on address 0x70 port 3
bus 4 on adapter 0 with a PCA9547 on address 0x70 port 4
bus 5 on adapter 0 with a PCA9547 on address 0x70 port 5
bus 6 on adapter 1 without a mux
bus 7 on adapter 1 with a PCA9544 on address 0x72 port 1
bus 8 on adapter 1 with a PCA9544 on address 0x72 port 2
If you do not have i2c muxes on your board, omit this define.Legacy I2C Support: CONFIG_HARD_I2C
NOTE: It is intended to move drivers to CONFIG_SYS_I2C which
provides the following compelling advantages:
- more than one i2c adapter is usable
- approved multibus support
- better i2c mux support
** Please consider updating your I2C driver now. **
These enable legacy I2C serial bus commands. Defining
CONFIG_HARD_I2C will include the appropriate I2C driver
for the selected CPU.
This will allow you to use i2c commands at the u-boot
command line (as long as you set CONFIG_CMD_I2C in
CONFIG_COMMANDS) and communicate with i2c based realtime
clock chips. See common/cmd_i2c.c for a description of the
command line interface.
CONFIG_HARD_I2C selects a hardware I2C controller.
There are several other quantities that must also be
defined when you define CONFIG_HARD_I2C.
In both cases you will need to define CONFIG_SYS_I2C_SPEED
to be the frequency (in Hz) at which you wish your i2c bus
to run and CONFIG_SYS_I2C_SLAVE to be the address of this node (ie
the CPU's i2c node address).
Now, the u-boot i2c code for the mpc8xx
(arch/powerpc/cpu/mpc8xx/i2c.c) sets the CPU up as a master node
and so its address should therefore be cleared to 0 (See,
eg, MPC823e User's Manual p.16-473). So, set
CONFIG_SYS_I2C_SLAVE to 0.
CONFIG_SYS_I2C_INIT_MPC5XXX
When a board is reset during an i2c bus transfer
chips might think that the current transfer is still
in progress. Reset the slave devices by sending start
commands until the slave device responds.
That's all that's required for CONFIG_HARD_I2C.
If you use the software i2c interface (CONFIG_SYS_I2C_SOFT)
then the following macros need to be defined (examples are
from include/configs/lwmon.h):
I2C_INIT
(Optional). Any commands necessary to enable the I2C
controller or configure ports.
eg: #define I2C_INIT (immr->im_cpm.cp_pbdir |= PB_SCL)
I2C_PORT
(Only for MPC8260 CPU). The I/O port to use (the code
assumes both bits are on the same port). Valid values
are 0..3 for ports A..D.
I2C_ACTIVE
The code necessary to make the I2C data line active
(driven). If the data line is open collector, this
define can be null.
eg: #define I2C_ACTIVE (immr->im_cpm.cp_pbdir |= PB_SDA)
I2C_TRISTATE
The code necessary to make the I2C data line tri-stated
(inactive). If the data line is open collector, this
define can be null.
eg: #define I2C_TRISTATE (immr->im_cpm.cp_pbdir &= ~PB_SDA)
I2C_READ
Code that returns true if the I2C data line is high,
false if it is low.
eg: #define I2C_READ ((immr->im_cpm.cp_pbdat & PB_SDA) != 0)
I2C_SDA(bit)
If <bit> is true, sets the I2C data line high. If it
is false, it clears it (low).
eg: #define I2C_SDA(bit) \
if(bit) immr->im_cpm.cp_pbdat |= PB_SDA; \
else immr->im_cpm.cp_pbdat &= ~PB_SDA
I2C_SCL(bit)
If <bit> is true, sets the I2C clock line high. If it
is false, it clears it (low).
eg: #define I2C_SCL(bit) \
if(bit) immr->im_cpm.cp_pbdat |= PB_SCL; \
else immr->im_cpm.cp_pbdat &= ~PB_SCL
I2C_DELAY
This delay is invoked four times per clock cycle so this
controls the rate of data transfer. The data rate thus
is 1 / (I2C_DELAY * 4). Often defined to be something
like:
#define I2C_DELAY udelay(2)
CONFIG_SOFT_I2C_GPIO_SCL / CONFIG_SOFT_I2C_GPIO_SDA
If your arch supports the generic GPIO framework (asm/gpio.h),
then you may alternatively define the two GPIOs that are to be
used as SCL / SDA. Any of the previous I2C_xxx macros will
have GPIO-based defaults assigned to them as appropriate.
You should define these to the GPIO value as given directly to
the generic GPIO functions.
CONFIG_SYS_I2C_INIT_BOARD
When a board is reset during an i2c bus transfer
chips might think that the current transfer is still
in progress. On some boards it is possible to access
the i2c SCLK line directly, either by using the
processor pin as a GPIO or by having a second pin
connected to the bus. If this option is defined a
custom i2c_init_board() routine in boards/xxx/board.c
is run early in the boot sequence.
CONFIG_SYS_I2C_BOARD_LATE_INIT
An alternative to CONFIG_SYS_I2C_INIT_BOARD. If this option is
defined a custom i2c_board_late_init() routine in
boards/xxx/board.c is run AFTER the operations in i2c_init()
is completed. This callpoint can be used to unreset i2c bus
using CPU i2c controller register accesses for CPUs whose i2c
controller provide such a method. It is called at the end of
i2c_init() to allow i2c_init operations to setup the i2c bus
controller on the CPU (e.g. setting bus speed & slave address).
CONFIG_I2CFAST (PPC405GP|PPC405EP only)
This option enables configuration of bi_iic_fast[] flags
in u-boot bd_info structure based on u-boot environment
variable "i2cfast". (see also i2cfast)
CONFIG_I2C_MULTI_BUS
This option allows the use of multiple I2C buses, each of which
must have a controller. At any point in time, only one bus is
active. To switch to a different bus, use the 'i2c dev' command.
Note that bus numbering is zero-based.
CONFIG_SYS_I2C_NOPROBES
This option specifies a list of I2C devices that will be skipped
when the 'i2c probe' command is issued. If CONFIG_I2C_MULTI_BUS
is set, specify a list of bus-device pairs. Otherwise, specify
a 1D array of device addresses
e.g.
#undef CONFIG_I2C_MULTI_BUS
#define CONFIG_SYS_I2C_NOPROBES {0x50,0x68}
will skip addresses 0x50 and 0x68 on a board with one I2C bus
#define CONFIG_I2C_MULTI_BUS
#define CONFIG_SYS_I2C_MULTI_NOPROBES {{0,0x50},{0,0x68},{1,0x54}}
will skip addresses 0x50 and 0x68 on bus 0 and address 0x54 on bus 1
CONFIG_SYS_SPD_BUS_NUM
If defined, then this indicates the I2C bus number for DDR SPD.
If not defined, then U-Boot assumes that SPD is on I2C bus 0.
CONFIG_SYS_RTC_BUS_NUM
If defined, then this indicates the I2C bus number for the RTC.
If not defined, then U-Boot assumes that RTC is on I2C bus 0.
CONFIG_SYS_DTT_BUS_NUM
If defined, then this indicates the I2C bus number for the DTT.
If not defined, then U-Boot assumes that DTT is on I2C bus 0.
CONFIG_SYS_I2C_DTT_ADDR:
If defined, specifies the I2C address of the DTT device.
If not defined, then U-Boot uses predefined value for
specified DTT device.
CONFIG_SOFT_I2C_READ_REPEATED_START
defining this will force the i2c_read() function in
the soft_i2c driver to perform an I2C repeated start
between writing the address pointer and reading the
data. If this define is omitted the default behaviour
of doing a stop-start sequence will be used. Most I2C
devices can use either method, but some require one or
the other.SPI Support: CONFIG_SPI
Enables SPI driver (so far only tested with
SPI EEPROM, also an instance works with Crystal A/D and
D/As on the SACSng board)
CONFIG_SH_SPI
Enables the driver for SPI controller on SuperH. Currently
only SH7757 is supported.
CONFIG_SPI_X
Enables extended (16-bit) SPI EEPROM addressing.
(symmetrical to CONFIG_I2C_X)
CONFIG_SOFT_SPI
Enables a software (bit-bang) SPI driver rather than
using hardware support. This is a general purpose
driver that only requires three general I/O port pins
(two outputs, one input) to function. If this is
defined, the board configuration must define several
SPI configuration items (port pins to use, etc). For
an example, see include/configs/sacsng.h.
CONFIG_HARD_SPI
Enables a hardware SPI driver for general-purpose reads
and writes. As with CONFIG_SOFT_SPI, the board configuration
must define a list of chip-select function pointers.
Currently supported on some MPC8xxx processors. For an
example, see include/configs/mpc8349emds.h.
CONFIG_MXC_SPI
Enables the driver for the SPI controllers on i.MX and MXC
SoCs. Currently i.MX31/35/51 are supported.
CONFIG_SYS_SPI_MXC_WAIT
Timeout for waiting until spi transfer completed.
default: (CONFIG_SYS_HZ/100) /* 10 ms */FPGA Support: CONFIG_FPGA
Enables FPGA subsystem.
CONFIG_FPGA_<vendor>
Enables support for specific chip vendors.
(ALTERA, XILINX)
CONFIG_FPGA_<family>
Enables support for FPGA family.
(SPARTAN2, SPARTAN3, VIRTEX2, CYCLONE2, ACEX1K, ACEX)
CONFIG_FPGA_COUNT
Specify the number of FPGA devices to support.
CONFIG_CMD_FPGA_LOADMK
Enable support for fpga loadmk command
CONFIG_CMD_FPGA_LOADP
Enable support for fpga loadp command - load partial bitstream
CONFIG_CMD_FPGA_LOADBP
Enable support for fpga loadbp command - load partial bitstream
(Xilinx only)
CONFIG_SYS_FPGA_PROG_FEEDBACK
Enable printing of hash marks during FPGA configuration.
CONFIG_SYS_FPGA_CHECK_BUSY
Enable checks on FPGA configuration interface busy
status by the configuration function. This option
will require a board or device specific function to
be written.
CONFIG_FPGA_DELAY
If defined, a function that provides delays in the FPGA
configuration driver.
CONFIG_SYS_FPGA_CHECK_CTRLC
Allow Control-C to interrupt FPGA configuration
CONFIG_SYS_FPGA_CHECK_ERROR
Check for configuration errors during FPGA bitfile
loading. For example, abort during Virtex II
configuration if the INIT_B line goes low (which
indicated a CRC error).
CONFIG_SYS_FPGA_WAIT_INIT
Maximum time to wait for the INIT_B line to de-assert
after PROB_B has been de-asserted during a Virtex II
FPGA configuration sequence. The default time is 500
ms.
CONFIG_SYS_FPGA_WAIT_BUSY
Maximum time to wait for BUSY to de-assert during
Virtex II FPGA configuration. The default is 5 ms.
CONFIG_SYS_FPGA_WAIT_CONFIG
Time to wait after FPGA configuration. The default is
200 ms.Configuration Management: CONFIG_BUILD_TARGET
Some SoCs need special image types (e.g. U-Boot binary
with a special header) as build targets. By defining
CONFIG_BUILD_TARGET in the SoC / board header, this
special image will be automatically built upon calling
make / MAKEALL.
CONFIG_IDENT_STRING
If defined, this string will be added to the U-Boot
version information (U_BOOT_VERSION)Vendor Parameter Protection:
U-Boot considers the values of the environment
variables "serial#" (Board Serial Number) and
"ethaddr" (Ethernet Address) to be parameters that
are set once by the board vendor / manufacturer, and
protects these variables from casual modification by
the user. Once set, these variables are read-only,
and write or delete attempts are rejected. You can
change this behaviour:
If CONFIG_ENV_OVERWRITE is #defined in your config
file, the write protection for vendor parameters is
completely disabled. Anybody can change or delete
these parameters.
Alternatively, if you define _both_ an ethaddr in the
default env _and_ CONFIG_OVERWRITE_ETHADDR_ONCE, a default
Ethernet address is installed in the environment,
which can be changed exactly ONCE by the user. [The
serial# is unaffected by this, i. e. it remains
read-only.]
The same can be accomplished in a more flexible way
for any variable by configuring the type of access
to allow for those variables in the ".flags" variable
or define CONFIG_ENV_FLAGS_LIST_STATIC.Protected RAM: CONFIG_PRAM
Define this variable to enable the reservation of
"protected RAM", i. e. RAM which is not overwritten
by U-Boot. Define CONFIG_PRAM to hold the number of
kB you want to reserve for pRAM. You can overwrite
this default value by defining an environment
variable "pram" to the number of kB you want to
reserve. Note that the board info structure will
still show the full amount of RAM. If pRAM is
reserved, a new environment variable "mem" will
automatically be defined to hold the amount of
remaining RAM in a form that can be passed as boot
argument to Linux, for instance like that:
setenv bootargs ... mem=\${mem}
saveenv
This way you can tell Linux not to use this memory,
either, which results in a memory region that will
not be affected by reboots.
*WARNING* If your board configuration uses automatic
detection of the RAM size, you must make sure that
this memory test is non-destructive. So far, the
following board configurations are known to be
"pRAM-clean":
IVMS8, IVML24, SPD8xx, TQM8xxL,
HERMES, IP860, RPXlite, LWMON,
FLAGADM, TQM8260Access to physical memory region (> 4GB) Some basic support is provided for operations on memory not normally accessible to U-Boot - e.g. some architectures support access to more than 4GB of memory on 32-bit machines using physical address extension or similar. Define CONFIG_PHYSMEM to access this basic support, which currently only supports clearing the memory.
Error Recovery: CONFIG_PANIC_HANG
Define this variable to stop the system in case of a
fatal error, so that you have to reset it manually.
This is probably NOT a good idea for an embedded
system where you want the system to reboot
automatically as fast as possible, but it may be
useful during development since you can try to debug
the conditions that lead to the situation.
CONFIG_NET_RETRY_COUNT
This variable defines the number of retries for
network operations like ARP, RARP, TFTP, or BOOTP
before giving up the operation. If not defined, a
default value of 5 is used.
CONFIG_ARP_TIMEOUT
Timeout waiting for an ARP reply in milliseconds.
CONFIG_NFS_TIMEOUT
Timeout in milliseconds used in NFS protocol.
If you encounter "ERROR: Cannot umount" in nfs command,
try longer timeout such as
#define CONFIG_NFS_TIMEOUT 10000ULCommand Interpreter: CONFIG_AUTO_COMPLETE
Enable auto completion of commands using TAB.
CONFIG_SYS_PROMPT_HUSH_PS2
This defines the secondary prompt string, which is
printed when the command interpreter needs more input
to complete a command. Usually "> ".Note:
In the current implementation, the local variables
space and global environment variables space are
separated. Local variables are those you define by
simply typing `name=value'. To access a local
variable later on, you have write `$name' or
`${name}'; to execute the contents of a variable
directly type `$name' at the command prompt.
Global environment variables are those you use
setenv/printenv to work with. To run a command stored
in such a variable, you need to use the run command,
and you must not use the '$' sign to access them.
To store commands and special characters in a
variable, please use double quotation marks
surrounding the whole text of the variable, instead
of the backslashes before semicolons and special
symbols.Command Line Editing and History: CONFIG_CMDLINE_EDITING
Enable editing and History functions for interactive
command line input operationsDefault Environment: CONFIG_EXTRA_ENV_SETTINGS
Define this to contain any number of null terminated
strings (variable = value pairs) that will be part of
the default environment compiled into the boot image.
For example, place something like this in your
board's config file:
#define CONFIG_EXTRA_ENV_SETTINGS \
"myvar1=value1\0" \
"myvar2=value2\0"
Warning: This method is based on knowledge about the
internal format how the environment is stored by the
U-Boot code. This is NOT an official, exported
interface! Although it is unlikely that this format
will change soon, there is no guarantee either.
You better know what you are doing here.
Note: overly (ab)use of the default environment is
discouraged. Make sure to check other ways to preset
the environment like the "source" command or the
boot command first.
CONFIG_ENV_VARS_UBOOT_CONFIG
Define this in order to add variables describing the
U-Boot build configuration to the default environment.
These will be named arch, cpu, board, vendor, and soc.
Enabling this option will cause the following to be defined:
- CONFIG_SYS_ARCH
- CONFIG_SYS_CPU
- CONFIG_SYS_BOARD
- CONFIG_SYS_VENDOR
- CONFIG_SYS_SOC
CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG
Define this in order to add variables describing certain
run-time determined information about the hardware to the
environment. These will be named board_name, board_rev.
CONFIG_DELAY_ENVIRONMENT
Normally the environment is loaded when the board is
initialised so that it is available to U-Boot. This inhibits
that so that the environment is not available until
explicitly loaded later by U-Boot code. With CONFIG_OF_CONTROL
this is instead controlled by the value of
/config/load-environment.Parallel Flash support: CONFIG_SYS_NO_FLASH
Traditionally U-boot was run on systems with parallel NOR
flash. This option is used to disable support for parallel NOR
flash. This option should be defined if the board does not have
parallel flash.
If this option is not defined one of the generic flash drivers
(e.g. CONFIG_FLASH_CFI_DRIVER or CONFIG_ST_SMI) must be
selected or the board must provide an implementation of the
flash API (see include/flash.h).DataFlash Support: CONFIG_HAS_DATAFLASH
Defining this option enables DataFlash features and
allows to read/write in Dataflash via the standard
commands cp, md...Serial Flash support CONFIG_CMD_SF
Defining this option enables SPI flash commands
'sf probe/read/write/erase/update'.
Usage requires an initial 'probe' to define the serial
flash parameters, followed by read/write/erase/update
commands.
The following defaults may be provided by the platform
to handle the common case when only a single serial
flash is present on the system.
CONFIG_SF_DEFAULT_BUS Bus identifier
CONFIG_SF_DEFAULT_CS Chip-select
CONFIG_SF_DEFAULT_MODE (see include/spi.h)
CONFIG_SF_DEFAULT_SPEED in Hz
CONFIG_CMD_SF_TEST
Define this option to include a destructive SPI flash
test ('sf test').
CONFIG_SF_DUAL_FLASH Dual flash memories
Define this option to use dual flash support where two flash
memories can be connected with a given cs line.
Currently Xilinx Zynq qspi supports these type of connections.SystemACE Support: CONFIG_SYSTEMACE
Adding this option adds support for Xilinx SystemACE
chips attached via some sort of local bus. The address
of the chip must also be defined in the
CONFIG_SYS_SYSTEMACE_BASE macro. For example:
#define CONFIG_SYSTEMACE
#define CONFIG_SYS_SYSTEMACE_BASE 0xf0000000
When SystemACE support is added, the "ace" device type
becomes available to the fat commands, i.e. fatls.TFTP Fixed UDP Port: CONFIG_TFTP_PORT
If this is defined, the environment variable tftpsrcp
is used to supply the TFTP UDP source port value.
If tftpsrcp isn't defined, the normal pseudo-random port
number generator is used.
Also, the environment variable tftpdstp is used to supply
the TFTP UDP destination port value. If tftpdstp isn't
defined, the normal port 69 is used.
The purpose for tftpsrcp is to allow a TFTP server to
blindly start the TFTP transfer using the pre-configured
target IP address and UDP port. This has the effect of
"punching through" the (Windows XP) firewall, allowing
the remainder of the TFTP transfer to proceed normally.
A better solution is to properly configure the firewall,
but sometimes that is not allowed.Hashing support: CONFIG_CMD_HASH
This enables a generic 'hash' command which can produce
hashes / digests from a few algorithms (e.g. SHA1, SHA256).
CONFIG_HASH_VERIFY
Enable the hash verify command (hash -v). This adds to code
size a little.
CONFIG_SHA1 - This option enables support of hashing using SHA1
algorithm. The hash is calculated in software.
CONFIG_SHA256 - This option enables support of hashing using
SHA256 algorithm. The hash is calculated in software.
CONFIG_SHA_HW_ACCEL - This option enables hardware acceleration
for SHA1/SHA256 hashing.
This affects the 'hash' command and also the
hash_lookup_algo() function.
CONFIG_SHA_PROG_HW_ACCEL - This option enables
hardware-acceleration for SHA1/SHA256 progressive hashing.
Data can be streamed in a block at a time and the hashing
is performed in hardware.
Note: There is also a sha1sum command, which should perhaps
be deprecated in favour of 'hash sha1'.Freescale i.MX specific commands: CONFIG_CMD_HDMIDETECT This enables 'hdmidet' command which returns true if an HDMI monitor is detected. This command is i.MX 6 specific.
CONFIG_CMD_BMODE
This enables the 'bmode' (bootmode) command for forcing
a boot from specific media.
This is useful for forcing the ROM's usb downloader to
activate upon a watchdog reset which is nice when iterating
on U-Boot. Using the reset button or running bmode normal
will set it back to normal. This command currently
supports i.MX53 and i.MX6.Signing support: CONFIG_RSA
This enables the RSA algorithm used for FIT image verification
in U-Boot. See doc/uImage.FIT/signature.txt for more information.
The Modular Exponentiation algorithm in RSA is implemented using
driver model. So CONFIG_DM needs to be enabled by default for this
library to function.
The signing part is build into mkimage regardless of this
option. The software based modular exponentiation is built into
mkimage irrespective of this option.bootcount support: CONFIG_BOOTCOUNT_LIMIT
This enables the bootcounter support, see:
http://www.denx.de/wiki/DULG/UBootBootCountLimit
CONFIG_AT91SAM9XE
enable special bootcounter support on at91sam9xe based boards.
CONFIG_BLACKFIN
enable special bootcounter support on blackfin based boards.
CONFIG_SOC_DA8XX
enable special bootcounter support on da850 based boards.
CONFIG_BOOTCOUNT_RAM
enable support for the bootcounter in RAM
CONFIG_BOOTCOUNT_I2C
enable support for the bootcounter on an i2c (like RTC) device.
CONFIG_SYS_I2C_RTC_ADDR = i2c chip address
CONFIG_SYS_BOOTCOUNT_ADDR = i2c addr which is used for
the bootcounter.
CONFIG_BOOTCOUNT_ALEN = address lenShow boot progress: CONFIG_SHOW_BOOT_PROGRESS
Defining this option allows to add some board-
specific code (calling a user-provided function
"show_boot_progress(int)") that enables you to show
the system's boot progress on some display (for
example, some LED's) on your board. At the moment,
the following checkpoints are implemented:Legacy uImage format:
Arg Where When 1 common/cmd_bootm.c before attempting to boot an image -1 common/cmd_bootm.c Image header has bad magic number 2 common/cmd_bootm.c Image header has correct magic number -2 common/cmd_bootm.c Image header has bad checksum 3 common/cmd_bootm.c Image header has correct checksum -3 common/cmd_bootm.c Image data has bad checksum 4 common/cmd_bootm.c Image data has correct checksum -4 common/cmd_bootm.c Image is for unsupported architecture 5 common/cmd_bootm.c Architecture check OK -5 common/cmd_bootm.c Wrong Image Type (not kernel, multi) 6 common/cmd_bootm.c Image Type check OK -6 common/cmd_bootm.c gunzip uncompression error -7 common/cmd_bootm.c Unimplemented compression type 7 common/cmd_bootm.c Uncompression OK 8 common/cmd_bootm.c No uncompress/copy overwrite error -9 common/cmd_bootm.c Unsupported OS (not Linux, BSD, VxWorks, QNX)
9 common/image.c Start initial ramdisk verification-10 common/image.c Ramdisk header has bad magic number -11 common/image.c Ramdisk header has bad checksum 10 common/image.c Ramdisk header is OK -12 common/image.c Ramdisk data has bad checksum 11 common/image.c Ramdisk data has correct checksum 12 common/image.c Ramdisk verification complete, start loading -13 common/image.c Wrong Image Type (not PPC Linux ramdisk) 13 common/image.c Start multifile image verification 14 common/image.c No initial ramdisk, no multifile, continue.
15 arch/
-30 arch/powerpc/lib/board.c Fatal error, hang the system -31 post/post.c POST test failed, detected by post_output_backlog() -32 post/post.c POST test failed, detected by post_run_single()
34 common/cmd_doc.c before loading a Image from a DOC device -35 common/cmd_doc.c Bad usage of "doc" command 35 common/cmd_doc.c correct usage of "doc" command -36 common/cmd_doc.c No boot device 36 common/cmd_doc.c correct boot device -37 common/cmd_doc.c Unknown Chip ID on boot device 37 common/cmd_doc.c correct chip ID found, device available -38 common/cmd_doc.c Read Error on boot device 38 common/cmd_doc.c reading Image header from DOC device OK -39 common/cmd_doc.c Image header has bad magic number 39 common/cmd_doc.c Image header has correct magic number -40 common/cmd_doc.c Error reading Image from DOC device 40 common/cmd_doc.c Image header has correct magic number 41 common/cmd_ide.c before loading a Image from a IDE device -42 common/cmd_ide.c Bad usage of "ide" command 42 common/cmd_ide.c correct usage of "ide" command -43 common/cmd_ide.c No boot device 43 common/cmd_ide.c boot device found -44 common/cmd_ide.c Device not available 44 common/cmd_ide.c Device available -45 common/cmd_ide.c wrong partition selected 45 common/cmd_ide.c partition selected -46 common/cmd_ide.c Unknown partition table 46 common/cmd_ide.c valid partition table found -47 common/cmd_ide.c Invalid partition type 47 common/cmd_ide.c correct partition type -48 common/cmd_ide.c Error reading Image Header on boot device 48 common/cmd_ide.c reading Image Header from IDE device OK -49 common/cmd_ide.c Image header has bad magic number 49 common/cmd_ide.c Image header has correct magic number -50 common/cmd_ide.c Image header has bad checksum 50 common/cmd_ide.c Image header has correct checksum -51 common/cmd_ide.c Error reading Image from IDE device 51 common/cmd_ide.c reading Image from IDE device OK 52 common/cmd_nand.c before loading a Image from a NAND device -53 common/cmd_nand.c Bad usage of "nand" command 53 common/cmd_nand.c correct usage of "nand" command -54 common/cmd_nand.c No boot device 54 common/cmd_nand.c boot device found -55 common/cmd_nand.c Unknown Chip ID on boot device 55 common/cmd_nand.c correct chip ID found, device available -56 common/cmd_nand.c Error reading Image Header on boot device 56 common/cmd_nand.c reading Image Header from NAND device OK -57 common/cmd_nand.c Image header has bad magic number 57 common/cmd_nand.c Image header has correct magic number -58 common/cmd_nand.c Error reading Image from NAND device 58 common/cmd_nand.c reading Image from NAND device OK
-60 common/env_common.c Environment has a bad CRC, using default
64 net/eth.c starting with Ethernet configuration. -64 net/eth.c no Ethernet found. 65 net/eth.c Ethernet found.
-80 common/cmd_net.c usage wrong 80 common/cmd_net.c before calling net_loop() -81 common/cmd_net.c some error in net_loop() occurred 81 common/cmd_net.c net_loop() back without error -82 common/cmd_net.c size == 0 (File with size 0 loaded) 82 common/cmd_net.c trying automatic boot 83 common/cmd_net.c running "source" command -83 common/cmd_net.c some error in automatic boot or "source" command 84 common/cmd_net.c end without errors
FIT uImage format:
Arg Where When 100 common/cmd_bootm.c Kernel FIT Image has correct format -100 common/cmd_bootm.c Kernel FIT Image has incorrect format 101 common/cmd_bootm.c No Kernel subimage unit name, using configuration -101 common/cmd_bootm.c Can't get configuration for kernel subimage 102 common/cmd_bootm.c Kernel unit name specified -103 common/cmd_bootm.c Can't get kernel subimage node offset 103 common/cmd_bootm.c Found configuration node 104 common/cmd_bootm.c Got kernel subimage node offset -104 common/cmd_bootm.c Kernel subimage hash verification failed 105 common/cmd_bootm.c Kernel subimage hash verification OK -105 common/cmd_bootm.c Kernel subimage is for unsupported architecture 106 common/cmd_bootm.c Architecture check OK -106 common/cmd_bootm.c Kernel subimage has wrong type 107 common/cmd_bootm.c Kernel subimage type OK -107 common/cmd_bootm.c Can't get kernel subimage data/size 108 common/cmd_bootm.c Got kernel subimage data/size -108 common/cmd_bootm.c Wrong image type (not legacy, FIT) -109 common/cmd_bootm.c Can't get kernel subimage type -110 common/cmd_bootm.c Can't get kernel subimage comp -111 common/cmd_bootm.c Can't get kernel subimage os -112 common/cmd_bootm.c Can't get kernel subimage load address -113 common/cmd_bootm.c Image uncompress/copy overwrite error
120 common/image.c Start initial ramdisk verification -120 common/image.c Ramdisk FIT image has incorrect format 121 common/image.c Ramdisk FIT image has correct format 122 common/image.c No ramdisk subimage unit name, using configuration -122 common/image.c Can't get configuration for ramdisk subimage 123 common/image.c Ramdisk unit name specified -124 common/image.c Can't get ramdisk subimage node offset 125 common/image.c Got ramdisk subimage node offset -125 common/image.c Ramdisk subimage hash verification failed 126 common/image.c Ramdisk subimage hash verification OK -126 common/image.c Ramdisk subimage for unsupported architecture 127 common/image.c Architecture check OK -127 common/image.c Can't get ramdisk subimage data/size 128 common/image.c Got ramdisk subimage data/size 129 common/image.c Can't get ramdisk load address -129 common/image.c Got ramdisk load address
-130 common/cmd_doc.c Incorrect FIT image format 131 common/cmd_doc.c FIT image format OK
-140 common/cmd_ide.c Incorrect FIT image format 141 common/cmd_ide.c FIT image format OK
-150 common/cmd_nand.c Incorrect FIT image format 151 common/cmd_nand.c FIT image format OK
legacy image format: CONFIG_IMAGE_FORMAT_LEGACY enables the legacy image format support in U-Boot.
Default:
enabled if CONFIG_FIT_SIGNATURE is not defined.
CONFIG_DISABLE_IMAGE_LEGACY
disable the legacy image format
This define is introduced, as the legacy image format is
enabled per default for backward compatibility.FIT image support: CONFIG_FIT Enable support for the FIT uImage format.
CONFIG_FIT_BEST_MATCH
When no configuration is explicitly selected, default to the
one whose fdt's compatibility field best matches that of
U-Boot itself. A match is considered "best" if it matches the
most specific compatibility entry of U-Boot's fdt's root node.
The order of entries in the configuration's fdt is ignored.
CONFIG_FIT_SIGNATURE
This option enables signature verification of FIT uImages,
using a hash signed and verified using RSA. If
CONFIG_SHA_PROG_HW_ACCEL is defined, i.e support for progressive
hashing is available using hardware, RSA library will use it.
See doc/uImage.FIT/signature.txt for more details.
WARNING: When relying on signed FIT images with required
signature check the legacy image format is default
disabled. If a board need legacy image format support
enable this through CONFIG_IMAGE_FORMAT_LEGACY
CONFIG_FIT_DISABLE_SHA256
Supporting SHA256 hashes has quite an impact on binary size.
For constrained systems sha256 hash support can be disabled
with this option.Standalone program support: CONFIG_STANDALONE_LOAD_ADDR
This option defines a board specific value for the
address where standalone program gets loaded, thus
overwriting the architecture dependent default
settings.Frame Buffer Address: CONFIG_FB_ADDR
Define CONFIG_FB_ADDR if you want to use specific
address for frame buffer. This is typically the case
when using a graphics controller has separate video
memory. U-Boot will then place the frame buffer at
the given address instead of dynamically reserving it
in system RAM by calling lcd_setmem(), which grabs
the memory for the frame buffer depending on the
configured panel size.
Please see board_init_f function.Automatic software updates via TFTP server CONFIG_UPDATE_TFTP CONFIG_UPDATE_TFTP_CNT_MAX CONFIG_UPDATE_TFTP_MSEC_MAX
These options enable and control the auto-update feature;
for a more detailed description refer to doc/README.update.MTD Support (mtdparts command, UBI support) CONFIG_MTD_DEVICE
Adds the MTD device infrastructure from the Linux kernel.
Needed for mtdparts command support.
CONFIG_MTD_PARTITIONS
Adds the MTD partitioning infrastructure from the Linux
kernel. Needed for UBI support.UBI support CONFIG_CMD_UBI
Adds commands for interacting with MTD partitions formatted
with the UBI flash translation layer
Requires also defining CONFIG_RBTREE
CONFIG_UBI_SILENCE_MSG
Make the verbose messages from UBI stop printing. This leaves
warnings and errors enabled.
CONFIG_MTD_UBI_WL_THRESHOLD
This parameter defines the maximum difference between the highest
erase counter value and the lowest erase counter value of eraseblocks
of UBI devices. When this threshold is exceeded, UBI starts performing
wear leveling by means of moving data from eraseblock with low erase
counter to eraseblocks with high erase counter.
The default value should be OK for SLC NAND flashes, NOR flashes and
other flashes which have eraseblock life-cycle 100000 or more.
However, in case of MLC NAND flashes which typically have eraseblock
life-cycle less than 10000, the threshold should be lessened (e.g.,
to 128 or 256, although it does not have to be power of 2).
default: 4096
CONFIG_MTD_UBI_BEB_LIMIT
This option specifies the maximum bad physical eraseblocks UBI
expects on the MTD device (per 1024 eraseblocks). If the
underlying flash does not admit of bad eraseblocks (e.g. NOR
flash), this value is ignored.
NAND datasheets often specify the minimum and maximum NVM
(Number of Valid Blocks) for the flashes' endurance lifetime.
The maximum expected bad eraseblocks per 1024 eraseblocks
then can be calculated as "1024 * (1 - MinNVB / MaxNVB)",
which gives 20 for most NANDs (MaxNVB is basically the total
count of eraseblocks on the chip).
To put it differently, if this value is 20, UBI will try to
reserve about 1.9% of physical eraseblocks for bad blocks
handling. And that will be 1.9% of eraseblocks on the entire
NAND chip, not just the MTD partition UBI attaches. This means
that if you have, say, a NAND flash chip admits maximum 40 bad
eraseblocks, and it is split on two MTD partitions of the same
size, UBI will reserve 40 eraseblocks when attaching a
partition.
default: 20
CONFIG_MTD_UBI_FASTMAP
Fastmap is a mechanism which allows attaching an UBI device
in nearly constant time. Instead of scanning the whole MTD device it
only has to locate a checkpoint (called fastmap) on the device.
The on-flash fastmap contains all information needed to attach
the device. Using fastmap makes only sense on large devices where
attaching by scanning takes long. UBI will not automatically install
a fastmap on old images, but you can set the UBI parameter
CONFIG_MTD_UBI_FASTMAP_AUTOCONVERT to 1 if you want so. Please note
that fastmap-enabled images are still usable with UBI implementations
without fastmap support. On typical flash devices the whole fastmap
fits into one PEB. UBI will reserve PEBs to hold two fastmaps.
CONFIG_MTD_UBI_FASTMAP_AUTOCONVERT
Set this parameter to enable fastmap automatically on images
without a fastmap.
default: 0UBIFS support CONFIG_CMD_UBIFS
Adds commands for interacting with UBI volumes formatted as
UBIFS. UBIFS is read-only in u-boot.
Requires UBI support as well as CONFIG_LZO
CONFIG_UBIFS_SILENCE_MSG
Make the verbose messages from UBIFS stop printing. This leaves
warnings and errors enabled.SPL framework CONFIG_SPL Enable building of SPL globally.
CONFIG_SPL_LDSCRIPT
LDSCRIPT for linking the SPL binary.
CONFIG_SPL_MAX_FOOTPRINT
Maximum size in memory allocated to the SPL, BSS included.
When defined, the linker checks that the actual memory
used by SPL from _start to __bss_end does not exceed it.
CONFIG_SPL_MAX_FOOTPRINT and CONFIG_SPL_BSS_MAX_SIZE
must not be both defined at the same time.
CONFIG_SPL_MAX_SIZE
Maximum size of the SPL image (text, data, rodata, and
linker lists sections), BSS excluded.
When defined, the linker checks that the actual size does
not exceed it.
CONFIG_SPL_TEXT_BASE
TEXT_BASE for linking the SPL binary.
CONFIG_SPL_RELOC_TEXT_BASE
Address to relocate to. If unspecified, this is equal to
CONFIG_SPL_TEXT_BASE (i.e. no relocation is done).
CONFIG_SPL_BSS_START_ADDR
Link address for the BSS within the SPL binary.
CONFIG_SPL_BSS_MAX_SIZE
Maximum size in memory allocated to the SPL BSS.
When defined, the linker checks that the actual memory used
by SPL from __bss_start to __bss_end does not exceed it.
CONFIG_SPL_MAX_FOOTPRINT and CONFIG_SPL_BSS_MAX_SIZE
must not be both defined at the same time.
CONFIG_SPL_STACK
Adress of the start of the stack SPL will use
CONFIG_SPL_PANIC_ON_RAW_IMAGE
When defined, SPL will panic() if the image it has
loaded does not have a signature.
Defining this is useful when code which loads images
in SPL cannot guarantee that absolutely all read errors
will be caught.
An example is the LPC32XX MLC NAND driver, which will
consider that a completely unreadable NAND block is bad,
and thus should be skipped silently.
CONFIG_SPL_RELOC_STACK
Adress of the start of the stack SPL will use after
relocation. If unspecified, this is equal to
CONFIG_SPL_STACK.
CONFIG_SYS_SPL_MALLOC_START
Starting address of the malloc pool used in SPL.
CONFIG_SYS_SPL_MALLOC_SIZE
The size of the malloc pool used in SPL.
CONFIG_SPL_FRAMEWORK
Enable the SPL framework under common/. This framework
supports MMC, NAND and YMODEM loading of U-Boot and NAND
NAND loading of the Linux Kernel.
CONFIG_SPL_OS_BOOT
Enable booting directly to an OS from SPL.
See also: doc/README.falcon
CONFIG_SPL_DISPLAY_PRINT
For ARM, enable an optional function to print more information
about the running system.
CONFIG_SPL_INIT_MINIMAL
Arch init code should be built for a very small image
CONFIG_SPL_LIBCOMMON_SUPPORT
Support for common/libcommon.o in SPL binary
CONFIG_SPL_LIBDISK_SUPPORT
Support for disk/libdisk.o in SPL binary
CONFIG_SPL_I2C_SUPPORT
Support for drivers/i2c/libi2c.o in SPL binary
CONFIG_SPL_GPIO_SUPPORT
Support for drivers/gpio/libgpio.o in SPL binary
CONFIG_SPL_MMC_SUPPORT
Support for drivers/mmc/libmmc.o in SPL binary
CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR,
CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS,
Address and partition on the MMC to load U-Boot from
when the MMC is being used in raw mode.
CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_PARTITION
Partition on the MMC to load U-Boot from when the MMC is being
used in raw mode
CONFIG_SYS_MMCSD_RAW_MODE_KERNEL_SECTOR
Sector to load kernel uImage from when MMC is being
used in raw mode (for Falcon mode)
CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTOR,
CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTORS
Sector and number of sectors to load kernel argument
parameters from when MMC is being used in raw mode
(for falcon mode)
CONFIG_SYS_MMCSD_FS_BOOT_PARTITION
Partition on the MMC to load U-Boot from when the MMC is being
used in fs mode
CONFIG_SPL_FAT_SUPPORT
Support for fs/fat/libfat.o in SPL binary
CONFIG_SPL_EXT_SUPPORT
Support for EXT filesystem in SPL binary
CONFIG_SPL_FS_LOAD_PAYLOAD_NAME
Filename to read to load U-Boot when reading from filesystem
CONFIG_SPL_FS_LOAD_KERNEL_NAME
Filename to read to load kernel uImage when reading
from filesystem (for Falcon mode)
CONFIG_SPL_FS_LOAD_ARGS_NAME
Filename to read to load kernel argument parameters
when reading from filesystem (for Falcon mode)
CONFIG_SPL_MPC83XX_WAIT_FOR_NAND
Set this for NAND SPL on PPC mpc83xx targets, so that
start.S waits for the rest of the SPL to load before
continuing (the hardware starts execution after just
loading the first page rather than the full 4K).
CONFIG_SPL_SKIP_RELOCATE
Avoid SPL relocation
CONFIG_SPL_NAND_BASE
Include nand_base.c in the SPL. Requires
CONFIG_SPL_NAND_DRIVERS.
CONFIG_SPL_NAND_DRIVERS
SPL uses normal NAND drivers, not minimal drivers.
CONFIG_SPL_NAND_ECC
Include standard software ECC in the SPL
CONFIG_SPL_NAND_SIMPLE
Support for NAND boot using simple NAND drivers that
expose the cmd_ctrl() interface.
CONFIG_SPL_MTD_SUPPORT
Support for the MTD subsystem within SPL. Useful for
environment on NAND support within SPL.
CONFIG_SPL_NAND_RAW_ONLY
Support to boot only raw u-boot.bin images. Use this only
if you need to save space.
CONFIG_SPL_MPC8XXX_INIT_DDR_SUPPORT
Set for the SPL on PPC mpc8xxx targets, support for
drivers/ddr/fsl/libddr.o in SPL binary.
CONFIG_SPL_COMMON_INIT_DDR
Set for common ddr init with serial presence detect in
SPL binary.
CONFIG_SYS_NAND_5_ADDR_CYCLE, CONFIG_SYS_NAND_PAGE_COUNT,
CONFIG_SYS_NAND_PAGE_SIZE, CONFIG_SYS_NAND_OOBSIZE,
CONFIG_SYS_NAND_BLOCK_SIZE, CONFIG_SYS_NAND_BAD_BLOCK_POS,
CONFIG_SYS_NAND_ECCPOS, CONFIG_SYS_NAND_ECCSIZE,
CONFIG_SYS_NAND_ECCBYTES
Defines the size and behavior of the NAND that SPL uses
to read U-Boot
CONFIG_SPL_NAND_BOOT
Add support NAND boot
CONFIG_SYS_NAND_U_BOOT_OFFS
Location in NAND to read U-Boot from
CONFIG_SYS_NAND_U_BOOT_DST
Location in memory to load U-Boot to
CONFIG_SYS_NAND_U_BOOT_SIZE
Size of image to load
CONFIG_SYS_NAND_U_BOOT_START
Entry point in loaded image to jump to
CONFIG_SYS_NAND_HW_ECC_OOBFIRST
Define this if you need to first read the OOB and then the
data. This is used, for example, on davinci platforms.
CONFIG_SPL_OMAP3_ID_NAND
Support for an OMAP3-specific set of functions to return the
ID and MFR of the first attached NAND chip, if present.
CONFIG_SPL_SERIAL_SUPPORT
Support for drivers/serial/libserial.o in SPL binary
CONFIG_SPL_SPI_FLASH_SUPPORT
Support for drivers/mtd/spi/libspi_flash.o in SPL binary
CONFIG_SPL_SPI_SUPPORT
Support for drivers/spi/libspi.o in SPL binary
CONFIG_SPL_RAM_DEVICE
Support for running image already present in ram, in SPL binary
CONFIG_SPL_LIBGENERIC_SUPPORT
Support for lib/libgeneric.o in SPL binary
CONFIG_SPL_ENV_SUPPORT
Support for the environment operating in SPL binary
CONFIG_SPL_NET_SUPPORT
Support for the net/libnet.o in SPL binary.
It conflicts with SPL env from storage medium specified by
CONFIG_ENV_IS_xxx but CONFIG_ENV_IS_NOWHERE
CONFIG_SPL_PAD_TO
Image offset to which the SPL should be padded before appending
the SPL payload. By default, this is defined as
CONFIG_SPL_MAX_SIZE, or 0 if CONFIG_SPL_MAX_SIZE is undefined.
CONFIG_SPL_PAD_TO must be either 0, meaning to append the SPL
payload without any padding, or >= CONFIG_SPL_MAX_SIZE.
CONFIG_SPL_TARGET
Final target image containing SPL and payload. Some SPLs
use an arch-specific makefile fragment instead, for
example if more than one image needs to be produced.
CONFIG_FIT_SPL_PRINT
Printing information about a FIT image adds quite a bit of
code to SPL. So this is normally disabled in SPL. Use this
option to re-enable it. This will affect the output of the
bootm command when booting a FIT image.TPL framework CONFIG_TPL Enable building of TPL globally.
CONFIG_TPL_PAD_TO
Image offset to which the TPL should be padded before appending
the TPL payload. By default, this is defined as
CONFIG_SPL_MAX_SIZE, or 0 if CONFIG_SPL_MAX_SIZE is undefined.
CONFIG_SPL_PAD_TO must be either 0, meaning to append the SPL
payload without any padding, or >= CONFIG_SPL_MAX_SIZE.[so far only for SMDK2400 boards]
Modem support enable: CONFIG_MODEM_SUPPORT
RTS/CTS Flow control enable: CONFIG_HWFLOW
Modem debug support: CONFIG_MODEM_SUPPORT_DEBUG
Enables debugging stuff (char screen[1024], dbg())
for modem support. Useful only with BDI2000.Interrupt support (PPC):
There are common interrupt_init() and timer_interrupt()
for all PPC archs. interrupt_init() calls interrupt_init_cpu()
for CPU specific initialization. interrupt_init_cpu()
should set decrementer_count to appropriate value. If
CPU resets decrementer automatically after interrupt
(ppc4xx) it should set decrementer_count to zero.
timer_interrupt() calls timer_interrupt_cpu() for CPU
specific handling. If board has watchdog / status_led
/ other_activity_monitor it works automatically from
general timer_interrupt().General:
In the target system modem support is enabled when a
specific key (key combination) is pressed during
power-on. Otherwise U-Boot will boot normally
(autoboot). The key_pressed() function is called from
board_init(). Currently key_pressed() is a dummy
function, returning 1 and thus enabling modem
initialization.
If there are no modem init strings in the
environment, U-Boot proceed to autoboot; the
previous output (banner, info printfs) will be
suppressed, though.
See also: doc/README.ModemDuring Initialization u-boot calls a number of board specific functions to allow the preparation of board specific prerequisites, e.g. pin setup before drivers are initialized. To enable these callbacks the following configuration macros have to be defined. Currently this is architecture specific, so please check arch/your_architecture/lib/board.c typically in board_init_f() and board_init_r().
CONFIG_SYS_SUPPORT_64BIT_DATA: Defined automatically if compiled as 64-bit. Optionally it can be defined to support 64-bit memory commands.
CONFIG_SYS_LONGHELP: Defined when you want long help messages included; undefine this when you're short of memory.
CONFIG_SYS_HELP_CMD_WIDTH: Defined when you want to override the default width of the commands listed in the 'help' command output.
CONFIG_SYS_PROMPT: This is what U-Boot prints on the console to prompt for user input.
CONFIG_SYS_CBSIZE: Buffer size for input from the Console
CONFIG_SYS_PBSIZE: Buffer size for Console output
CONFIG_SYS_MAXARGS: max. Number of arguments accepted for monitor commands
CONFIG_SYS_BARGSIZE: Buffer size for Boot Arguments which are passed to the application (usually a Linux kernel) when it is booted
CONFIG_SYS_BAUDRATE_TABLE: List of legal baudrate settings for this board.
CONFIG_SYS_CONSOLE_INFO_QUIET Suppress display of console information at boot.
CONFIG_SYS_CONSOLE_IS_IN_ENV If the board specific function extern int overwrite_console (void); returns 1, the stdin, stderr and stdout are switched to the serial port, else the settings in the environment are used.
CONFIG_SYS_CONSOLE_OVERWRITE_ROUTINE Enable the call to overwrite_console().
CONFIG_SYS_CONSOLE_ENV_OVERWRITE Enable overwrite of previous console environment settings.
CONFIG_SYS_MEMTEST_START, CONFIG_SYS_MEMTEST_END: Begin and End addresses of the area used by the simple memory test.
CONFIG_SYS_ALT_MEMTEST: Enable an alternate, more extensive memory test.
CONFIG_SYS_MEMTEST_SCRATCH: Scratch address used by the alternate memory test You only need to set this if address zero isn't writeable
CONFIG_SYS_MEM_TOP_HIDE (PPC only): If CONFIG_SYS_MEM_TOP_HIDE is defined in the board config header, this specified memory area will get subtracted from the top (end) of RAM and won't get "touched" at all by U-Boot. By fixing up gd->ram_size the Linux kernel should gets passed the now "corrected" memory size and won't touch it either. This should work for arch/ppc and arch/powerpc. Only Linux board ports in arch/powerpc with bootwrapper support that recalculate the memory size from the SDRAM controller setup will have to get fixed in Linux additionally.
This option can be used as a workaround for the 440EPx/GRx
CHIP 11 errata where the last 256 bytes in SDRAM shouldn't
be touched.
WARNING: Please make sure that this value is a multiple of
the Linux page size (normally 4k). If this is not the case,
then the end address of the Linux memory will be located at a
non page size aligned address and this could cause major
problems.CONFIG_SYS_LOADS_BAUD_CHANGE: Enable temporary baudrate change while serial download
CONFIG_SYS_SDRAM_BASE: Physical start address of SDRAM. Must be 0 here.
CONFIG_SYS_MBIO_BASE: Physical start address of Motherboard I/O (if using a Cogent motherboard)
CONFIG_SYS_FLASH_BASE: Physical start address of Flash memory.
CONFIG_SYS_MONITOR_BASE: Physical start address of boot monitor code (set by make config files to be same as the text base address (CONFIG_SYS_TEXT_BASE) used when linking) - same as CONFIG_SYS_FLASH_BASE when booting from flash.
CONFIG_SYS_MONITOR_LEN: Size of memory reserved for monitor code, used to determine _at_compiletime (!) if the environment is embedded within the U-Boot image, or in a separate flash sector.
CONFIG_SYS_MALLOC_LEN: Size of DRAM reserved for malloc() use.
CONFIG_SYS_MALLOC_F_LEN Size of the malloc() pool for use before relocation. If this is defined, then a very simple malloc() implementation will become available before relocation. The address is just below the global data, and the stack is moved down to make space.
This feature allocates regions with increasing addresses
within the region. calloc() is supported, but realloc()
is not available. free() is supported but does nothing.
The memory will be freed (or in fact just forgotten) when
U-Boot relocates itself.
Pre-relocation malloc() is only supported on ARM and sandbox
at present but is fairly easy to enable for other archs.CONFIG_SYS_MALLOC_SIMPLE Provides a simple and small malloc() and calloc() for those boards which do not use the full malloc in SPL (which is enabled with CONFIG_SYS_SPL_MALLOC_START).
CONFIG_SYS_NONCACHED_MEMORY: Size of non-cached memory area. This area of memory will be typically located right below the malloc() area and mapped uncached in the MMU. This is useful for drivers that would otherwise require a lot of explicit cache maintenance. For some drivers it's also impossible to properly maintain the cache. For example if the regions that need to be flushed are not a multiple of the cache-line size, and padding cannot be allocated between the regions to align them (i.e. if the HW requires a contiguous array of regions, and the size of each region is not cache-aligned), then a flush of one region may result in overwriting data that hardware has written to another region in the same cache-line. This can happen for example in network drivers where descriptors for buffers are typically smaller than the CPU cache-line (e.g. 16 bytes vs. 32 or 64 bytes).
Non-cached memory is only supported on 32-bit ARM at present.CONFIG_SYS_BOOTM_LEN: Normally compressed uImages are limited to an uncompressed size of 8 MBytes. If this is not enough, you can define CONFIG_SYS_BOOTM_LEN in your board config file to adjust this setting to your needs.
CONFIG_SYS_BOOTMAPSZ: Maximum size of memory mapped by the startup code of the Linux kernel; all data that must be processed by the Linux kernel (bd_info, boot arguments, FDT blob if used) must be put below this limit, unless "bootm_low" environment variable is defined and non-zero. In such case all data for the Linux kernel must be between "bootm_low" and "bootm_low" + CONFIG_SYS_BOOTMAPSZ. The environment variable "bootm_mapsize" will override the value of CONFIG_SYS_BOOTMAPSZ. If CONFIG_SYS_BOOTMAPSZ is undefined, then the value in "bootm_size" will be used instead.
CONFIG_SYS_BOOT_RAMDISK_HIGH: Enable initrd_high functionality. If defined then the initrd_high feature is enabled and the bootm ramdisk subcommand is enabled.
CONFIG_SYS_BOOT_GET_CMDLINE: Enables allocating and saving kernel cmdline in space between "bootm_low" and "bootm_low" + BOOTMAPSZ.
CONFIG_SYS_BOOT_GET_KBD: Enables allocating and saving a kernel copy of the bd_info in space between "bootm_low" and "bootm_low" + BOOTMAPSZ.
CONFIG_SYS_MAX_FLASH_BANKS: Max number of Flash memory banks
CONFIG_SYS_MAX_FLASH_SECT: Max number of sectors on a Flash chip
CONFIG_SYS_FLASH_ERASE_TOUT: Timeout for Flash erase operations (in ms)
CONFIG_SYS_FLASH_WRITE_TOUT: Timeout for Flash write operations (in ms)
CONFIG_SYS_FLASH_LOCK_TOUT Timeout for Flash set sector lock bit operation (in ms)
CONFIG_SYS_FLASH_UNLOCK_TOUT Timeout for Flash clear lock bits operation (in ms)
CONFIG_SYS_FLASH_PROTECTION If defined, hardware flash sectors protection is used instead of U-Boot software protection.
CONFIG_SYS_DIRECT_FLASH_TFTP:
Enable TFTP transfers directly to flash memory;
without this option such a download has to be
performed in two steps: (1) download to RAM, and (2)
copy from RAM to flash.
The two-step approach is usually more reliable, since
you can check if the download worked before you erase
the flash, but in some situations (when system RAM is
too limited to allow for a temporary copy of the
downloaded image) this option may be very useful.CONFIG_SYS_FLASH_CFI: Define if the flash driver uses extra elements in the common flash structure for storing flash geometry.
CONFIG_FLASH_CFI_DRIVER This option also enables the building of the cfi_flash driver in the drivers directory
CONFIG_FLASH_CFI_MTD This option enables the building of the cfi_mtd driver in the drivers directory. The driver exports CFI flash to the MTD layer.
CONFIG_SYS_FLASH_USE_BUFFER_WRITE Use buffered writes to flash.
CONFIG_FLASH_SPANSION_S29WS_N s29ws-n MirrorBit flash has non-standard addresses for buffered write commands.
CONFIG_SYS_FLASH_QUIET_TEST If this option is defined, the common CFI flash doesn't print it's warning upon not recognized FLASH banks. This is useful, if some of the configured banks are only optionally available.
CONFIG_FLASH_SHOW_PROGRESS If defined (must be an integer), print out countdown digits and dots. Recommended value: 45 (9..1) for 80 column displays, 15 (3..1) for 40 column displays.
CONFIG_FLASH_VERIFY If defined, the content of the flash (destination) is compared against the source after the write operation. An error message will be printed when the contents are not identical. Please note that this option is useless in nearly all cases, since such flash programming errors usually are detected earlier while unprotecting/erasing/programming. Please only enable this option if you really know what you are doing.
CONFIG_SYS_RX_ETH_BUFFER: Defines the number of Ethernet receive buffers. On some Ethernet controllers it is recommended to set this value to 8 or even higher (EEPRO100 or 405 EMAC), since all buffers can be full shortly after enabling the interface on high Ethernet traffic. Defaults to 4 if not defined.
CONFIG_ENV_MAX_ENTRIES
Maximum number of entries in the hash table that is used internally to store the environment settings. The default setting is supposed to be generous and should work in most cases. This setting can be used to tune behaviour; see lib/hashtable.c for details.
CONFIG_ENV_FLAGS_LIST_DEFAULT
CONFIG_ENV_FLAGS_LIST_STATIC Enable validation of the values given to environment variables when calling env set. Variables can be restricted to only decimal, hexadecimal, or boolean. If CONFIG_CMD_NET is also defined, the variables can also be restricted to IP address or MAC address.
The format of the list is: type_attribute = [s|d|x|b|i|m] access_attribute = [a|r|o|c] attributes = type_attribute[access_attribute] entry = variable_name[:attributes] list = entry[,list]
The type attributes are: s - String (default) d - Decimal x - Hexadecimal b - Boolean ([1yYtT|0nNfF]) i - IP address m - MAC address
The access attributes are: a - Any (default) r - Read-only o - Write-once c - Change-default
CONFIG_ENV_FLAGS_LIST_DEFAULT Define this to a list (string) to define the ".flags" environment variable in the default or embedded environment.
CONFIG_ENV_FLAGS_LIST_STATIC Define this to a list (string) to define validation that should be done if an entry is not found in the ".flags" environment variable. To override a setting in the static list, simply add an entry for the same variable name to the ".flags" variable.
If CONFIG_REGEX is defined, the variable_name above is evaluated as a regular expression. This allows multiple variables to define the same flags without explicitly listing them for each variable.
CONFIG_ENV_ACCESS_IGNORE_FORCE If defined, don't allow the -f switch to env set override variable access flags.
CONFIG_SYS_GENERIC_BOARD This selects the architecture-generic board system instead of the architecture-specific board files. It is intended to move boards to this new framework over time. Defining this will disable the arch/foo/lib/board.c file and use common/board_f.c and common/board_r.c instead. To use this option your architecture must support it (i.e. must select HAVE_GENERIC_BOARD in arch/Kconfig). If you find problems enabling this option on your board please report the problem and send patches!
CONFIG_OMAP_PLATFORM_RESET_TIME_MAX_USEC (OMAP only) This is set by OMAP boards for the max time that reset should be asserted. See doc/README.omap-reset-time for details on how the value can be calculated on a given board.
CONFIG_USE_STDINT If stdint.h is available with your toolchain you can define this option to enable it. You can provide option 'USE_STDINT=1' when building U-Boot to enable this.
The following definitions that deal with the placement and management of environment data (variable area); in general, we support the following configurations:
CONFIG_BUILD_ENVCRC:
Builds up envcrc with the target environment so that external utils may easily extract it and embed it in final U-Boot images.
CONFIG_ENV_IS_IN_FLASH:
Define this if the environment is in flash memory.
a) The environment occupies one whole flash sector, which is "embedded" in the text segment with the U-Boot code. This happens usually with "bottom boot sector" or "top boot sector" type flash chips, which have several smaller sectors at the start or the end. For instance, such a layout can have sector sizes of 8, 2x4, 16, Nx32 kB. In such a case you would place the environment in one of the 4 kB sectors - with U-Boot code before and after it. With "top boot sector" type flash chips, you would put the environment in one of the last sectors, leaving a gap between U-Boot and the environment.
CONFIG_ENV_OFFSET:
Offset of environment data (variable area) to the beginning of flash memory; for instance, with bottom boot type flash chips the second sector can be used: the offset for this sector is given here.
CONFIG_ENV_OFFSET is used relative to CONFIG_SYS_FLASH_BASE.
CONFIG_ENV_ADDR:
This is just another way to specify the start address of the flash sector containing the environment (instead of CONFIG_ENV_OFFSET).
CONFIG_ENV_SECT_SIZE:
Size of the sector containing the environment.
b) Sometimes flash chips have few, equal sized, BIG sectors. In such a case you don't want to spend a whole sector for the environment.
CONFIG_ENV_SIZE:
If you use this in combination with CONFIG_ENV_IS_IN_FLASH and CONFIG_ENV_SECT_SIZE, you can specify to use only a part of this flash sector for the environment. This saves memory for the RAM copy of the environment.
It may also save flash memory if you decide to use this when your environment is "embedded" within U-Boot code, since then the remainder of the flash sector could be used for U-Boot code. It should be pointed out that this is STRONGLY DISCOURAGED from a robustness point of view: updating the environment in flash makes it always necessary to erase the WHOLE sector. If something goes wrong before the contents has been restored from a copy in RAM, your target system will be dead.
CONFIG_ENV_ADDR_REDUND CONFIG_ENV_SIZE_REDUND
These settings describe a second storage area used to hold a redundant copy of the environment data, so that there is a valid backup copy in case there is a power failure during a "saveenv" operation.
BE CAREFUL! Any changes to the flash layout, and some changes to the
source code will make it necessary to adapt
CONFIG_ENV_IS_IN_NVRAM:
Define this if you have some non-volatile memory device (NVRAM, battery buffered SRAM) which you want to use for the environment.
CONFIG_ENV_SIZE:
These two #defines are used to determine the memory area you want to use for environment. It is assumed that this memory can just be read and written to, without any special provision.
BE CAREFUL! The first access to the environment happens quite early in U-Boot initialization (when we try to get the setting of for the console baudrate). You MUST have mapped your NVRAM area then, or U-Boot will hang.
Please note that even with NVRAM we still use a copy of the environment in RAM: we could work on NVRAM directly, but we want to keep settings there always unmodified except somebody uses "saveenv" to save the current settings.
CONFIG_ENV_IS_IN_EEPROM:
Use this if you have an EEPROM or similar serial access device and a driver for it.
CONFIG_ENV_OFFSET:
CONFIG_ENV_SIZE:
These two #defines specify the offset and size of the environment area within the total memory of your EEPROM.
CONFIG_SYS_I2C_EEPROM_ADDR: If defined, specified the chip address of the EEPROM device. The default address is zero.
CONFIG_SYS_I2C_EEPROM_BUS: If defined, specified the i2c bus of the EEPROM device.
CONFIG_SYS_EEPROM_PAGE_WRITE_BITS: If defined, the number of bits used to address bytes in a single page in the EEPROM device. A 64 byte page, for example would require six bits.
CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS: If defined, the number of milliseconds to delay between page writes. The default is zero milliseconds.
CONFIG_SYS_I2C_EEPROM_ADDR_LEN: The length in bytes of the EEPROM memory array address. Note that this is NOT the chip address length!
CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW: EEPROM chips that implement "address overflow" are ones like Catalyst 24WC04/08/16 which has 9/10/11 bits of address and the extra bits end up in the "chip address" bit slots. This makes a 24WC08 (1Kbyte) chip look like four 256 byte chips.
Note that we consider the length of the address field to still be one byte because the extra address bits are hidden in the chip address.
CONFIG_SYS_EEPROM_SIZE: The size in bytes of the EEPROM device.
CONFIG_ENV_EEPROM_IS_ON_I2C define this, if you have I2C and SPI activated, and your EEPROM, which holds the environment, is on the I2C bus.
CONFIG_I2C_ENV_EEPROM_BUS if you have an Environment on an EEPROM reached over I2C muxes, you can define here, how to reach this EEPROM. For example:
EEPROM which holds the environment, is reached over a pca9547 i2c mux with address 0x70, channel 3.
CONFIG_ENV_IS_IN_DATAFLASH:
Define this if you have a DataFlash memory device which you want to use for the environment.
CONFIG_ENV_SIZE:
These three #defines specify the offset and size of the environment area within the total memory of your DataFlash placed at the specified address.
CONFIG_ENV_IS_IN_SPI_FLASH:
Define this if you have a SPI Flash memory device which you want to use for the environment.
CONFIG_ENV_OFFSET:
CONFIG_ENV_SIZE:
These two #defines specify the offset and size of the environment area within the SPI Flash. CONFIG_ENV_OFFSET must be aligned to an erase sector boundary.
CONFIG_ENV_SECT_SIZE:
Define the SPI flash's sector size.
CONFIG_ENV_OFFSET_REDUND (optional):
This setting describes a second storage area of CONFIG_ENV_SIZE size used to hold a redundant copy of the environment data, so that there is a valid backup copy in case there is a power failure during a "saveenv" operation. CONFIG_ENV_OFFSET_RENDUND must be aligned to an erase sector boundary.
CONFIG_ENV_SPI_BUS (optional):
CONFIG_ENV_SPI_CS (optional):
Define the SPI bus and chip select. If not defined they will be 0.
CONFIG_ENV_SPI_MAX_HZ (optional):
Define the SPI max work clock. If not defined then use 1MHz.
CONFIG_ENV_SPI_MODE (optional):
Define the SPI work mode. If not defined then use SPI_MODE_3.
CONFIG_ENV_IS_IN_REMOTE:
Define this if you have a remote memory space which you want to use for the local device's environment.
CONFIG_ENV_SIZE:
These two #defines specify the address and size of the environment area within the remote memory space. The local device can get the environment from remote memory space by SRIO or PCIE links.
BE CAREFUL! For some special cases, the local device can not use "saveenv" command. For example, the local device will get the environment stored in a remote NOR flash by SRIO or PCIE link, but it can not erase, write this NOR flash by SRIO or PCIE interface.
CONFIG_ENV_IS_IN_NAND:
Define this if you have a NAND device which you want to use for the environment.
CONFIG_ENV_OFFSET:
CONFIG_ENV_SIZE:
These two #defines specify the offset and size of the environment area within the first NAND device. CONFIG_ENV_OFFSET must be aligned to an erase block boundary.
CONFIG_ENV_OFFSET_REDUND (optional):
This setting describes a second storage area of CONFIG_ENV_SIZE size used to hold a redundant copy of the environment data, so that there is a valid backup copy in case there is a power failure during a "saveenv" operation. CONFIG_ENV_OFFSET_RENDUND must be aligned to an erase block boundary.
CONFIG_ENV_RANGE (optional):
Specifies the length of the region in which the environment can be written. This should be a multiple of the NAND device's block size. Specifying a range with more erase blocks than are needed to hold CONFIG_ENV_SIZE allows bad blocks within the range to be avoided.
CONFIG_ENV_OFFSET_OOB (optional):
Enables support for dynamically retrieving the offset of the environment from block zero's out-of-band data. The "nand env.oob" command can be used to record this offset. Currently, CONFIG_ENV_OFFSET_REDUND is not supported when using CONFIG_ENV_OFFSET_OOB.
CONFIG_NAND_ENV_DST
Defines address in RAM to which the nand_spl code should copy the environment. If redundant environment is used, it will be copied to CONFIG_NAND_ENV_DST + CONFIG_ENV_SIZE.
CONFIG_ENV_IS_IN_UBI:
Define this if you have an UBI volume that you want to use for the environment. This has the benefit of wear-leveling the environment accesses, which is important on NAND.
CONFIG_ENV_UBI_PART:
Define this to a string that is the mtd partition containing the UBI.
CONFIG_ENV_UBI_VOLUME:
Define this to the name of the volume that you want to store the environment in.
CONFIG_ENV_UBI_VOLUME_REDUND:
Define this to the name of another volume to store a second copy of the environment in. This will enable redundant environments in UBI. It is assumed that both volumes are in the same MTD partition.
CONFIG_UBI_SILENCE_MSG
CONFIG_UBIFS_SILENCE_MSG
You will probably want to define these to avoid a really noisy system when storing the env in UBI.
CONFIG_ENV_IS_IN_FAT: Define this if you want to use the FAT file system for the environment.
FAT_ENV_INTERFACE:
Define this to a string that is the name of the block device.
FAT_ENV_DEV_AND_PART:
Define this to a string to specify the partition of the device. It can be as following:
"D:P", "D:0", "D", "D:" or "D:auto" (D, P are integers. And P >= 1)
FAT_ENV_FILE:
It's a string of the FAT file name. This file use to store the environment.
CONFIG_FAT_WRITE: This should be defined. Otherwise it cannot save the environment file.
CONFIG_ENV_IS_IN_MMC:
Define this if you have an MMC device which you want to use for the environment.
CONFIG_SYS_MMC_ENV_DEV:
Specifies which MMC device the environment is stored in.
CONFIG_SYS_MMC_ENV_PART (optional):
Specifies which MMC partition the environment is stored in. If not set, defaults to partition 0, the user area. Common values might be 1 (first MMC boot partition), 2 (second MMC boot partition).
CONFIG_ENV_OFFSET:
CONFIG_ENV_SIZE:
These two #defines specify the offset and size of the environment area within the specified MMC device.
If offset is positive (the usual case), it is treated as relative to the start of the MMC partition. If offset is negative, it is treated as relative to the end of the MMC partition. This can be useful if your board may be fitted with different MMC devices, which have different sizes for the MMC partitions, and you always want the environment placed at the very end of the partition, to leave the maximum possible space before it, to store other data.
These two values are in units of bytes, but must be aligned to an MMC sector boundary.
CONFIG_ENV_OFFSET_REDUND (optional):
Specifies a second storage area, of CONFIG_ENV_SIZE size, used to hold a redundant copy of the environment data. This provides a valid backup copy in case the other copy is corrupted, e.g. due to a power failure during a "saveenv" operation.
This value may also be positive or negative; this is handled in the same way as CONFIG_ENV_OFFSET.
This value is also in units of bytes, but must also be aligned to an MMC sector boundary.
CONFIG_ENV_SIZE_REDUND (optional):
This value need not be set, even when CONFIG_ENV_OFFSET_REDUND is set. If this value is set, it must be set to the same value as CONFIG_ENV_SIZE.
CONFIG_SYS_SPI_INIT_OFFSET
Defines offset to the initial SPI buffer area in DPRAM. The area is used at an early stage (ROM part) if the environment is configured to reside in the SPI EEPROM: We need a 520 byte scratch DPRAM area. It is used between the two initialization calls (spi_init_f() and spi_init_r()). A value of 0xB00 seems to be a good choice since it makes it far enough from the start of the data area as well as from the stack pointer.
Please note that the environment is read-only until the monitor has been relocated to RAM and a RAM copy of the environment has been created; also, when using EEPROM you will have to use getenv_f() until then to read environment variables.
The environment is protected by a CRC32 checksum. Before the monitor is relocated into RAM, as a result of a bad CRC you will be working with the compiled-in default environment - silently!!! [This is necessary, because the first environment variable we need is the "baudrate" setting for the console - if we have a bad CRC, we don't have any device yet where we could complain.]
Note: once the monitor has been relocated, then it will complain if the default environment is used; a new CRC is computed as soon as you use the "saveenv" command to store a valid environment.
CONFIG_SYS_FAULT_ECHO_LINK_DOWN: Echo the inverted Ethernet link state to the fault LED.
Note: If this option is active, then CONFIG_SYS_FAULT_MII_ADDR
also needs to be defined.CONFIG_SYS_FAULT_MII_ADDR: MII address of the PHY to check for the Ethernet link state.
CONFIG_NS16550_MIN_FUNCTIONS: Define this if you desire to only have use of the NS16550_init and NS16550_putc functions for the serial driver located at drivers/serial/ns16550.c. This option is useful for saving space for already greatly restricted images, including but not limited to NAND_SPL configurations.
CONFIG_DISPLAY_BOARDINFO Display information about the board that U-Boot is running on when U-Boot starts up. The board function checkboard() is called to do this.
CONFIG_DISPLAY_BOARDINFO_LATE Similar to the previous option, but display this information later, once stdio is running and output goes to the LCD, if present.
CONFIG_BOARD_SIZE_LIMIT: Maximum size of the U-Boot image. When defined, the build system checks that the actual size does not exceed it.
CONFIG_SYS_CACHELINE_SIZE: Cache Line Size of the CPU.
CONFIG_SYS_DEFAULT_IMMR: Default address of the IMMR after system reset.
Needed on some 8260 systems (MPC8260ADS, PQ2FADS-ZU,
and RPXsuper) to be able to adjust the position of
the IMMR register after a reset.CONFIG_SYS_CCSRBAR_DEFAULT: Default (power-on reset) physical address of CCSR on Freescale PowerPC SOCs.
CONFIG_SYS_CCSRBAR: Virtual address of CCSR. On a 32-bit build, this is typically the same value as CONFIG_SYS_CCSRBAR_DEFAULT.
CONFIG_SYS_DEFAULT_IMMR must also be set to this value,
for cross-platform code that uses that macro instead.CONFIG_SYS_CCSRBAR_PHYS: Physical address of CCSR. CCSR can be relocated to a new physical address, if desired. In this case, this macro should be set to that address. Otherwise, it should be set to the same value as CONFIG_SYS_CCSRBAR_DEFAULT. For example, CCSR is typically relocated on 36-bit builds. It is recommended that this macro be defined via the _HIGH and _LOW macros:
#define CONFIG_SYS_CCSRBAR_PHYS ((CONFIG_SYS_CCSRBAR_PHYS_HIGH
* 1ull) << 32 | CONFIG_SYS_CCSRBAR_PHYS_LOW)CONFIG_SYS_CCSRBAR_PHYS_HIGH: Bits 33-36 of CONFIG_SYS_CCSRBAR_PHYS. This value is typically either 0 (32-bit build) or 0xF (36-bit build). This macro is used in assembly code, so it must not contain typecasts or integer size suffixes (e.g. "ULL").
CONFIG_SYS_CCSRBAR_PHYS_LOW: Lower 32-bits of CONFIG_SYS_CCSRBAR_PHYS. This macro is used in assembly code, so it must not contain typecasts or integer size suffixes (e.g. "ULL").
CONFIG_SYS_CCSR_DO_NOT_RELOCATE: If this macro is defined, then CONFIG_SYS_CCSRBAR_PHYS will be forced to a value that ensures that CCSR is not relocated.
Floppy Disk Support: CONFIG_SYS_FDC_DRIVE_NUMBER
the default drive number (default value 0)
CONFIG_SYS_ISA_IO_STRIDE
defines the spacing between FDC chipset registers
(default value 1)
CONFIG_SYS_ISA_IO_OFFSET
defines the offset of register from address. It
depends on which part of the data bus is connected to
the FDC chipset. (default value 0)
If CONFIG_SYS_ISA_IO_STRIDE CONFIG_SYS_ISA_IO_OFFSET and
CONFIG_SYS_FDC_DRIVE_NUMBER are undefined, they take their
default value.
if CONFIG_SYS_FDC_HW_INIT is defined, then the function
fdc_hw_init() is called at the beginning of the FDC
setup. fdc_hw_init() must be provided by the board
source code. It is used to make hardware-dependent
initializations.CONFIG_IDE_AHB: Most IDE controllers were designed to be connected with PCI interface. Only few of them were designed for AHB interface. When software is doing ATA command and data transfer to IDE devices through IDE-AHB controller, some additional registers accessing to these kind of IDE-AHB controller is required.
CONFIG_SYS_IMMR: Physical address of the Internal Memory. DO NOT CHANGE unless you know exactly what you're doing! (11-4) [MPC8xx/82xx systems only]
CONFIG_SYS_INIT_RAM_ADDR:
Start address of memory area that can be used for
initial data and stack; please note that this must be
writable memory that is working WITHOUT special
initialization, i. e. you CANNOT use normal RAM which
will become available only after programming the
memory controller and running certain initialization
sequences.
U-Boot uses the following memory types:
- MPC8xx and MPC8260: IMMR (internal memory of the CPU)
- MPC824X: data cache
- PPC4xx: data cacheCONFIG_SYS_GBL_DATA_OFFSET:
Offset of the initial data structure in the memory
area defined by CONFIG_SYS_INIT_RAM_ADDR. Usually
CONFIG_SYS_GBL_DATA_OFFSET is chosen such that the initial
data is located at the end of the available space
(sometimes written as (CONFIG_SYS_INIT_RAM_SIZE -
CONFIG_SYS_INIT_DATA_SIZE), and the initial stack is just
below that area (growing from (CONFIG_SYS_INIT_RAM_ADDR +
CONFIG_SYS_GBL_DATA_OFFSET) downward.Note: On the MPC824X (or other systems that use the data cache for initial memory) the address chosen for CONFIG_SYS_INIT_RAM_ADDR is basically arbitrary - it must point to an otherwise UNUSED address space between the top of RAM and the start of the PCI space.
CONFIG_SYS_SIUMCR: SIU Module Configuration (11-6)
CONFIG_SYS_SYPCR: System Protection Control (11-9)
CONFIG_SYS_TBSCR: Time Base Status and Control (11-26)
CONFIG_SYS_PISCR: Periodic Interrupt Status and Control (11-31)
CONFIG_SYS_PLPRCR: PLL, Low-Power, and Reset Control Register (15-30)
CONFIG_SYS_SCCR: System Clock and reset Control Register (15-27)
CONFIG_SYS_OR_TIMING_SDRAM: SDRAM timing
CONFIG_SYS_MAMR_PTA: periodic timer for refresh
CONFIG_SYS_DER: Debug Event Register (37-47)
FLASH_BASE0_PRELIM, FLASH_BASE1_PRELIM, CONFIG_SYS_REMAP_OR_AM, CONFIG_SYS_PRELIM_OR_AM, CONFIG_SYS_OR_TIMING_FLASH, CONFIG_SYS_OR0_REMAP, CONFIG_SYS_OR0_PRELIM, CONFIG_SYS_BR0_PRELIM, CONFIG_SYS_OR1_REMAP, CONFIG_SYS_OR1_PRELIM, CONFIG_SYS_BR1_PRELIM: Memory Controller Definitions: BR0/1 and OR0/1 (FLASH)
SDRAM_BASE2_PRELIM, SDRAM_BASE3_PRELIM, SDRAM_MAX_SIZE, CONFIG_SYS_OR_TIMING_SDRAM, CONFIG_SYS_OR2_PRELIM, CONFIG_SYS_BR2_PRELIM, CONFIG_SYS_OR3_PRELIM, CONFIG_SYS_BR3_PRELIM: Memory Controller Definitions: BR2/3 and OR2/3 (SDRAM)
CONFIG_SYS_MAMR_PTA, CONFIG_SYS_MPTPR_2BK_4K, CONFIG_SYS_MPTPR_1BK_4K, CONFIG_SYS_MPTPR_2BK_8K, CONFIG_SYS_MPTPR_1BK_8K, CONFIG_SYS_MAMR_8COL, CONFIG_SYS_MAMR_9COL: Machine Mode Register and Memory Periodic Timer Prescaler definitions (SDRAM timing)
CONFIG_SYS_I2C_UCODE_PATCH, CONFIG_SYS_I2C_DPMEM_OFFSET [0x1FC0]: enable I2C microcode relocation patch (MPC8xx); define relocation offset in DPRAM [DSP2]
CONFIG_SYS_SMC_UCODE_PATCH, CONFIG_SYS_SMC_DPMEM_OFFSET [0x1FC0]: enable SMC microcode relocation patch (MPC8xx); define relocation offset in DPRAM [SMC1]
CONFIG_SYS_SPI_UCODE_PATCH, CONFIG_SYS_SPI_DPMEM_OFFSET [0x1FC0]: enable SPI microcode relocation patch (MPC8xx); define relocation offset in DPRAM [SCC4]
CONFIG_SYS_USE_OSCCLK: Use OSCM clock mode on MBX8xx board. Be careful, wrong setting might damage your board. Read doc/README.MBX before setting this variable!
CONFIG_SYS_CPM_POST_WORD_ADDR: (MPC8xx, MPC8260 only) Offset of the bootmode word in DPRAM used by post (Power On Self Tests). This definition overrides
cpm_8260.h.CONFIG_SYS_PCI_SLV_MEM_LOCAL, CONFIG_SYS_PCI_SLV_MEM_BUS, CONFIG_SYS_PICMR0_MASK_ATTRIB, CONFIG_SYS_PCI_MSTR0_LOCAL, CONFIG_SYS_PCIMSK0_MASK, CONFIG_SYS_PCI_MSTR1_LOCAL, CONFIG_SYS_PCIMSK1_MASK, CONFIG_SYS_PCI_MSTR_MEM_LOCAL, CONFIG_SYS_PCI_MSTR_MEM_BUS, CONFIG_SYS_CPU_PCI_MEM_START, CONFIG_SYS_PCI_MSTR_MEM_SIZE, CONFIG_SYS_POCMR0_MASK_ATTRIB, CONFIG_SYS_PCI_MSTR_MEMIO_LOCAL, CONFIG_SYS_PCI_MSTR_MEMIO_BUS, CPU_PCI_MEMIO_START, CONFIG_SYS_PCI_MSTR_MEMIO_SIZE, CONFIG_SYS_POCMR1_MASK_ATTRIB, CONFIG_SYS_PCI_MSTR_IO_LOCAL, CONFIG_SYS_PCI_MSTR_IO_BUS, CONFIG_SYS_CPU_PCI_IO_START, CONFIG_SYS_PCI_MSTR_IO_SIZE, CONFIG_SYS_POCMR2_MASK_ATTRIB: (MPC826x only) Overrides the default PCI memory map in arch/powerpc/cpu/mpc8260/pci.c if set.
CONFIG_PCI_DISABLE_PCIE: Disable PCI-Express on systems where it is supported but not required.
CONFIG_PCI_ENUM_ONLY Only scan through and get the devices on the buses. Don't do any setup work, presumably because someone or something has already done it, and we don't need to do it a second time. Useful for platforms that are pre-booted by coreboot or similar.
CONFIG_PCI_INDIRECT_BRIDGE: Enable support for indirect PCI bridges.
CONFIG_SYS_SRIO: Chip has SRIO or not
CONFIG_SRIO1: Board has SRIO 1 port available
CONFIG_SRIO2: Board has SRIO 2 port available
CONFIG_SRIO_PCIE_BOOT_MASTER Board can support master function for Boot from SRIO and PCIE
CONFIG_SYS_SRIOn_MEM_VIRT: Virtual Address of SRIO port 'n' memory region
CONFIG_SYS_SRIOn_MEM_PHYS: Physical Address of SRIO port 'n' memory region
CONFIG_SYS_SRIOn_MEM_SIZE: Size of SRIO port 'n' memory region
CONFIG_SYS_NAND_BUSWIDTH_16BIT Defined to tell the NAND controller that the NAND chip is using a 16 bit bus. Not all NAND drivers use this symbol. Example of drivers that use it:
CONFIG_SYS_NDFC_EBC0_CFG Sets the EBC0_CFG register for the NDFC. If not defined a default value will be used.
CONFIG_SPD_EEPROM Get DDR timing information from an I2C EEPROM. Common with pluggable memory modules such as SODIMMs
SPD_EEPROM_ADDRESS I2C address of the SPD EEPROM
CONFIG_SYS_SPD_BUS_NUM If SPD EEPROM is on an I2C bus other than the first one, specify here. Note that the value must resolve to something your driver can deal with.
CONFIG_SYS_DDR_RAW_TIMING Get DDR timing information from other than SPD. Common with soldered DDR chips onboard without SPD. DDR raw timing parameters are extracted from datasheet and hard-coded into header files or board specific files.
CONFIG_FSL_DDR_INTERACTIVE Enable interactive DDR debugging. See doc/README.fsl-ddr.
CONFIG_FSL_DDR_SYNC_REFRESH Enable sync of refresh for multiple controllers.
CONFIG_FSL_DDR_BIST Enable built-in memory test for Freescale DDR controllers.
CONFIG_SYS_83XX_DDR_USES_CS0 Only for 83xx systems. If specified, then DDR should be configured using CS0 and CS1 instead of CS2 and CS3.
CONFIG_ETHER_ON_FEC[12] Define to enable FEC[12] on a 8xx series processor.
CONFIG_FEC[12]_PHY Define to the hardcoded PHY address which corresponds to the given FEC; i. e.
means that the PHY with address 4 is connected to FEC1
When set to -1, means to probe for first available.CONFIG_FEC[12]_PHY_NORXERR The PHY does not have a RXERR line (RMII only). (so program the FEC to ignore it).
CONFIG_RMII Enable RMII mode for all FECs. Note that this is a global option, we can't have one FEC in standard MII mode and another in RMII mode.
CONFIG_CRC32_VERIFY Add a verify option to the crc32 command. The syntax is:
=> crc32 -v <address> <count> <crc32>
Where address/count indicate a memory area
and crc32 is the correct crc32 which the
area should have.CONFIG_LOOPW Add the "loopw" memory command. This only takes effect if the memory commands are activated globally (CONFIG_CMD_MEM).
CONFIG_MX_CYCLIC Add the "mdc" and "mwc" memory commands. These are cyclic "md/mw" commands. Examples:
=> mdc.b 10 4 500
This command will print 4 bytes (10,11,12,13) each 500 ms.
=> mwc.l 100 12345678 10
This command will write 12345678 to address 100 all 10 ms.
This only takes effect if the memory commands are activated
globally (CONFIG_CMD_MEM).CONFIG_SKIP_LOWLEVEL_INIT [ARM, NDS32, MIPS only] If this variable is defined, then certain low level initializations (like setting up the memory controller) are omitted and/or U-Boot does not relocate itself into RAM.
Normally this variable MUST NOT be defined. The only
exception is when U-Boot is loaded (to RAM) by some
other boot loader or by a debugger which performs
these initializations itself.CONFIG_SPL_BUILD Modifies the behaviour of start.S when compiling a loader that is executed before the actual U-Boot. E.g. when compiling a NAND SPL.
CONFIG_TPL_BUILD Modifies the behaviour of start.S when compiling a loader that is executed after the SPL and before the actual U-Boot. It is loaded by the SPL.
CONFIG_SYS_MPC85XX_NO_RESETVEC Only for 85xx systems. If this variable is specified, the section .resetvec is not kept and the section .bootpg is placed in the previous 4k of the .text section.
CONFIG_ARCH_MAP_SYSMEM Generally U-Boot (and in particular the md command) uses effective address. It is therefore not necessary to regard U-Boot address as virtual addresses that need to be translated to physical addresses. However, sandbox requires this, since it maintains its own little RAM buffer which contains all addressable memory. This option causes some memory accesses to be mapped through map_sysmem() / unmap_sysmem().
CONFIG_USE_ARCH_MEMCPY CONFIG_USE_ARCH_MEMSET If these options are used a optimized version of memcpy/memset will be used if available. These functions may be faster under some conditions but may increase the binary size.
CONFIG_X86_RESET_VECTOR If defined, the x86 reset vector code is included. This is not needed when U-Boot is running from Coreboot.
CONFIG_SYS_MPUCLK Defines the MPU clock speed (in MHz).
NOTE : currently only supported on AM335x platforms.CONFIG_SPL_AM33XX_ENABLE_RTC32K_OSC: Enables the RTC32K OSC on AM33xx based plattforms
CONFIG_SYS_NAND_NO_SUBPAGE_WRITE Option to disable subpage write in NAND driver driver that uses this: drivers/mtd/nand/davinci_nand.c
The Freescale QUICCEngine (QE) and Frame Manager (FMAN) both support the loading of "firmware", which is encoded in the QE firmware binary format. This firmware often needs to be loaded during U-Boot booting, so macros are used to identify the storage device (NOR flash, SPI, etc) and the address within that device.
CONFIG_SYS_FMAN_FW_ADDR The address in the storage device where the FMAN microcode is located. The meaning of this address depends on which CONFIG_SYS_QE_FW_IN_xxx macro is also specified.
CONFIG_SYS_QE_FW_ADDR The address in the storage device where the QE microcode is located. The meaning of this address depends on which CONFIG_SYS_QE_FW_IN_xxx macro is also specified.
CONFIG_SYS_QE_FMAN_FW_LENGTH The maximum possible size of the firmware. The firmware binary format has a field that specifies the actual size of the firmware, but it might not be possible to read any part of the firmware unless some local storage is allocated to hold the entire firmware first.
CONFIG_SYS_QE_FMAN_FW_IN_NOR Specifies that QE/FMAN firmware is located in NOR flash, mapped as normal addressable memory via the LBC. CONFIG_SYS_FMAN_FW_ADDR is the virtual address in NOR flash.
CONFIG_SYS_QE_FMAN_FW_IN_NAND Specifies that QE/FMAN firmware is located in NAND flash. CONFIG_SYS_FMAN_FW_ADDR is the offset within NAND flash.
CONFIG_SYS_QE_FMAN_FW_IN_MMC Specifies that QE/FMAN firmware is located on the primary SD/MMC device. CONFIG_SYS_FMAN_FW_ADDR is the byte offset on that device.
CONFIG_SYS_QE_FMAN_FW_IN_SPIFLASH Specifies that QE/FMAN firmware is located on the primary SPI device. CONFIG_SYS_FMAN_FW_ADDR is the byte offset on that device.
CONFIG_SYS_QE_FMAN_FW_IN_REMOTE Specifies that QE/FMAN firmware is located in the remote (master) memory space. CONFIG_SYS_FMAN_FW_ADDR is a virtual address which can be mapped from slave TLB->slave LAW->slave SRIO or PCIE outbound window->master inbound window->master LAW->the ucode address in master's memory space.
The Freescale Layerscape Management Complex (MC) supports the loading of "firmware". This firmware often needs to be loaded during U-Boot booting, so macros are used to identify the storage device (NOR flash, SPI, etc) and the address within that device.
CONFIG_FSL_MC_ENET Enable the MC driver for Layerscape SoCs.
CONFIG_SYS_LS_MC_FW_ADDR The address in the storage device where the firmware is located. The meaning of this address depends on which CONFIG_SYS_LS_MC_FW_IN_xxx macro is also specified.
CONFIG_SYS_LS_MC_FW_LENGTH The maximum possible size of the firmware. The firmware binary format has a field that specifies the actual size of the firmware, but it might not be possible to read any part of the firmware unless some local storage is allocated to hold the entire firmware first.
CONFIG_SYS_LS_MC_FW_IN_NOR Specifies that MC firmware is located in NOR flash, mapped as normal addressable memory via the LBC. CONFIG_SYS_LS_MC_FW_ADDR is the virtual address in NOR flash.
Building U-Boot has been tested in several native build environments and in many different cross environments. Of course we cannot support all possibly existing versions of cross development tools in all (potentially obsolete) versions. In case of tool chain problems we recommend to use the ELDK (see http://www.denx.de/wiki/DULG/ELDK) which is extensively used to build and test U-Boot.
If you are not using a native environment, it is assumed that you have GNU cross compiling tools available in your path. In this case, you must set the environment variable CROSS_COMPILE in your shell. Note that no changes to the Makefile or any other source files are necessary. For example using the ELDK on a 4xx CPU, please enter:
$ CROSS_COMPILE=ppc_4xx-
$ export CROSS_COMPILENote: If you wish to generate Windows versions of the utilities in the tools directory you can use the MinGW toolchain (http://www.mingw.org). Set your HOST tools to the MinGW toolchain and execute 'make tools'. For example:
$ make HOSTCC=i586-mingw32msvc-gcc HOSTSTRIP=i586-mingw32msvc-strip tools
Binaries such as tools/mkimage.exe will be created which can
be executed on computers running Windows.U-Boot is intended to be simple to build. After installing the sources you must configure U-Boot for one specific board type. This is done by typing:
make NAME_defconfigwhere "NAME_defconfig" is the name of one of the existing configu- rations; see boards.cfg for supported names.
Note: for some board special configuration names may exist; check if additional information is available from the board vendor; for instance, the TQM823L systems are available without (standard) or with LCD support. You can select such additional "features" when choosing the configuration, i. e.
make TQM823L_defconfig
- will configure for a plain TQM823L, i. e. no LCD support
make TQM823L_LCD_defconfig
- will configure for a TQM823L with U-Boot console on LCD
etc.Finally, type "make all", and you should get some working U-Boot images ready for download to / installation on your system:
By default the build is performed locally and the objects are saved in the source directory. One of the two methods can be used to change this behavior and build U-Boot to some external directory:
Add O= to the make command line invocations:
make O=/tmp/build distclean make O=/tmp/build NAME_defconfig make O=/tmp/build all
Set environment variable KBUILD_OUTPUT to point to the desired location:
export KBUILD_OUTPUT=/tmp/build make distclean make NAME_defconfig make all
Note that the command line "O=" setting overrides the KBUILD_OUTPUT environment variable.
Please be aware that the Makefiles assume you are using GNU make, so for instance on NetBSD you might need to use "gmake" instead of native "make".
If the system board that you have is not listed, then you will need to port U-Boot to your hardware platform. To do this, follow these steps:
If you have modified U-Boot sources (for instance added a new board or support for new devices, a new CPU, etc.) you are expected to provide feedback to the other developers. The feedback normally takes the form of a "patch", i. e. a context diff against a certain (latest official or latest in the git repository) version of U-Boot sources.
But before you submit such a patch, please verify that your modifi- cation did not break existing code. At least make sure that ALL of the supported boards compile WITHOUT ANY compiler warnings. To do so, just run the "MAKEALL" script, which will configure and build U-Boot for ALL supported system. Be warned, this will take a while. You can select which (cross) compiler to use by passing a `CROSS_COMPILE' environment variable to the script, i. e. to use the ELDK cross tools you can type
CROSS_COMPILE=ppc_8xx- MAKEALLor to build on a native PowerPC system you can type
CROSS_COMPILE=' ' MAKEALLWhen using the MAKEALL script, the default behaviour is to build
U-Boot in the source directory. This location can be changed by
setting the BUILD_DIR environment variable. Also, for each target
built, the MAKEALL script saves two log files (