A toolkit for patching HPE's iLO 4 firmware with access to previously inaccessible utilities.
Specifically, firmware is patched with the ability to access new commands via SSH, relating to system health (h), fan tuning (fan), on-board temperature sensors (ocsd), and option chip health systems (ocbb). Designed for /r/homelab users, this modified firmware provides administrators with the ability to adjust HP's aggressive fan curves on iLO4-equipped servers (such as DL380p / DL380p Gen 8 & Gen 9). Another common use case is to prevent server fans from maxing out when a non-HPE certified PCI-e card is used in a system.
Please note: At this time, v2.77 is the most recent iLO that has a working patch. After this version, HP has removed many of the control utilities that make patching v2.78 and v2.79 useful. While this may change in the future, bringing useful tools to v2.79 (the current latest) will take an extremely large amount of work. The patching works fine here, it just does not provide access to useful functions
There is risk for potential damage to your system when utilizing this code. If an error occurs during flashing, or you end up flashing corrupted firmware, the iLO will not be able to recover itself. The iLO's flash chip cannot be programmed on-board, and must be fully desoldered and reprogrammed to recover the functionality. Additionally, utilizing the included new features may cause your server to overheat or otherwise suffer damage. Do not proceed with installing this firmware if you don't know what you're doing. You have been warned. There is no warranty for this code nor will I be responsible for any damage you cause. I have personally only tested this firmware on my DL380p Gen8, and DL380e Gen8.
This repo does not contain any iLO 4 binaries; unmodified or patched as they are owned by HP. Websites have, in the past, been served with cease and desist orders from HP for hosting iLO binaries. For security purposes, I encourage you to follow the steps listed to build the patched version of the iLO yourself, while verifying the contents of the patched code.
Python 2.7 is required. I built everything on CentOS 8; Other OS/environments might have different requirements. If your setup takes extra effort, please let me know and I'll document it.
pro tip! if you're doing this all on a Live CD to flash, make sure you disable iLO security first, or you'll have to restart. See Flashing Firmware for more info
Here is my setup for my Ubuntu 21.10 Live CD:
sudo apt-add-repository universe
sudo apt update
sudo apt-get install python2-minimal git curl
curl https://bootstrap.pypa.io/pip/2.7/get-pip.py --output get-pip.py && sudo python2 get-pip.py
python2 -m pip install virtualenv
git clone --recurse-submodules https://github.com/kendallgoto/ilo4_unlock.git
cd ilo4_unlock
python2 -m virtualenv venv
source venv/bin/activate
pip install -r requirements.txt./build.sh init # download necessary HPE binaries
#./build.sh [patch-name] -- see patches/ folder for more info on each patch!
./build.sh 277 # generate iLO v2.77 patched firmware
# The build setup creates a build/ folder where all the artifacts are stored. The final firmware location will be printed at the end of the script, if no errors are produced.The resulting firmware is located in the build directory, under the firmware's name (e.g. build/ilo4_273.bin.patched for v2.73 builds). I suggest the following steps to flash the firmware, as you cannot do it from the web interface:
binaries/flash_ilo4 & binaries/CP027911.xml)sudo modprobe -r hpilo)ilo4_250.bin, then run sudo ./flash_ilo4 --direct to patch your server.Following the Getting Started steps, here's what I did after building:
sudo modprobe -r hpilo
mkdir -p flash
cp binaries/flash_ilo4 binaries/CP027911.xml flash/
cp build/ilo4_277.bin.patched flash/ilo4_250.bin
cd flash
sudo ./flash_ilo4 --direct
# wait until the fans spin down ...
sudo shutdown now # remove power and disable the security override after shutting down!FAN:
Usage:
info [t|h|a|g|p]
- display information about the fan controller
or individual information.
g - configure the 'global' section of the fan controller
g smsc|start|stop|status
start - start the iLO fan controller
stop - stop the iLO fan controller
smsc - configure the SMSC for manual control
ro|rw|nc - set the RO, RW, NC (no_commit) options
(blank) - shows current status
t - configure the 'temperature' section of the fan controller
t N on|off|adj|hyst|caut|crit|access|opts|set|unset
on - enable temperature sensor
off - disable temperature sensor
adj - set ADJUSTMENT/OFFSET
set/unset - set or clear a fixed simulated temp (also 'fan t set/unset' for show/clear all)
hyst - set hysteresis for sensor
caut - set CAUTION threshold
crit - set CRITICAL threshold
access - set ACCESS method for sensor (should be followed by 5 BYTES)
opts - set the OPTION field
h - configure the 'tacHometers' section of the fan controller
h N on|off|min|hyst|access
on - enable sensor N
off - disable sensor N
min - set MINIMUM tach threshold
hyst - set hysteresis
grp ocsd|show - show grouping parameters with OCSD impacts
p - configure the PWM configuration
p N on|off|min|max|hyst|blow|pctramp|zero|feton|bon|boff|status|lock X|unlock|tickler|fix|fet|access
on - enable (toggle) specified PWM
off - disable (toggle) specified PWM
min - set MINIMUM speed
max - set MAXIMUM speed
blow - set BLOWOUT speed
pct - set the PERCETNAGE blowout bits
ramp - set the RAMP register
zero - set the force ZEROP bit on/off
feton - set the FET 'for off' bit on/off
bon - set BLOWOUT on
boff - set BLOWOUT off
status - set STATUS register
lock - set LOCK speed and set LOCK bit
unlock - clear the LOCK bit
tickler - set TICKLER bit on/off - tickles fans even if FAN is stopped
pid - configure the PID algorithm
pid N p|i|d|sp|imin|imax|lo|hi - configure PID paramaters
- * Use correct FORMAT for numbers!
p - set the PROPORTIONAL gain
i - set the INTEGRAL gain
d - set the DERIVATIVE gain
sp - set SETPOINT
imin - set I windup MIN value
imax - set I windup MAX value
lo - set output LOW limit
hi - set output HIGH lmit
MISC
rate X - Change rate to X ms polling (default 3000)
ramp - Force a RAMP condition
dump - Dump all the fan registers in raw HEX format
hyst h v1..vN - Perform a test hysteresis with supplied numbers
desc <0>..<15> - try to decode then execute raw descriptor bytes (5 or 16)
actn <0>..<15> - try to decode then execute raw action bytes (5 or 16)
debug trace|t X|h X|a X|g X|p X|off|on
- Set the fine control values for the fan FYI level
DIMM - DIMM-specific subcommand handler
DRIVE - Drive temperature subcommand handler
MB - Memory buffer subcommand handler
PECI - PECI subcommand handler
AWAITING DOCUMENTAION
ms - multi-segment info
a N - algorithms - set parameters for multi-segment.
w - weightingSee the scripts/ folder as well. For info about the lesser used functions, please refer to the relevant reading. I don't use them, so I haven't documented them.
Want to get involved? Check out here!
The full documentation on how this code base was derived is fully detailed in the research/ folder.
2019-10-02 /u/phoenixdev's preliminary writeup
2019-10-15 /u/phoenixdev's first release for v2.60
2020-06-30 /u/phoenixdev's second release for v2.73
Airbus Security Lab's iLO4 Toolbox
Airbus Security Lab's "Subverting your server through its BMC: the HPE iLO4 case" (written version)
Airbus Security Lab's "Subverting your server through its BMC: the HPE iLO4 case" (presented version)