Wireless debugging with only one ESP Chip !
Realized by USBIP and CMSIS-DAP protocol stack.
👉 5m range, 100kb size firmware(Hex) earse and download test:
For Keil users, we now also support elaphureLink. No need for usbip to start your wireless debugging!
SoC Compatibility
Debug Communication Mode
USB Communication Mode
Debug Trace (Uart)
More..
The default connected WIFI SSID is 无线DAP
, password 12345678
Support for specifying multiple possible WAP. It can be added here: wifi_configuration.h
You can also specify your IP in the above file (We recommend using the static address binding feature of the router).
There is built-in ipv4 only mDNS server. You can access the device using dap.local
.
You can build locally or use Github Action to build online and then download firmware to flash.
Start ESP chip and connect it to the device to be debugged
Connect it with usbip:
# HID Mode only
# for pre-compiled version on SourceForge
# or usbip old version
.\usbip.exe -D -a <your-esp-device-ip-address> 1-1
# 👉 Recommend
# HID Mode Or WinUSB Mode
# for usbip-win 0.3.0 kmdf ude
.\usbip.exe attach_ude -r <your-esp-device-ip-address> -b 1-1
If all goes well, you should see your device connected.
Here, we use MDK for testing:
Note that this project is sensitive to the network environment. If you are using a hotspot on your computer, you can try using network analyzer such as wireshark to observe the status of your AP network. During the idle time, the network should stay silent, while in the working state, there should be no too much packet loss.
Some LAN broadcast packets can cause serious impact, including:
It is also affected by the surrounding radio environment, your AP situation (some NICs have terrible AP performance), distance, etc.
The maximum rate of esp8266 pure IO is about 2MHz. When you select max clock, we will take the following actions:
clock < 2Mhz
: Similar to the clock speed you choose.2MHz <= clock < 10MHz
: Use the fastest pure IO speed.clock >= 10MHz
: SPI acceleration using 40MHz clock.Note that the most significant speed constraint of this project is still the TCP connection speed.
This project was originally designed to run on Keil, but now you can also perform firmware flash on OpenOCD.
> halt
> flash write_image [erase] [unlock] filename [offset] [type]
pyOCD is now supported.
TCP server on PORT 1234.
UART default baud: 74880
This feature provides a bridge between TCP and Uart:
Send data -> TCP -> Uart TX -> external devices
Recv data <- TCP <- Uart Rx <- external devices
When the TCP connection is established, bridge will try to resolve the text sent for the first packet. When the text is a valid baud rate, bridge will switch to it.
For example, sending the ASCII text 115200
will switch the baud rate to 115200.
2020.12.1
TCP transmission speed needs to be further improved.
2020.11.11
Winusb is now available, but it is very slow.
2020.2.4
Due to the limitation of USB-HID (I'm not sure if this is a problem with USBIP or Windows), now each URB packet can only reach 255 bytes (About 1MBps bandwidth), which has not reached the upper limit of ESP8266 transmission bandwidth.
I now have an idea to construct a Man-in-the-middle between the two to forward traffic, thereby increasing the bandwidth of each transmission.
2020.1.31
At present, the adaptation to WCID, WinUSB, etc. has all been completed. However, when transmitting data on the endpoint, we received an error message from USBIP. This is most likely a problem with the USBIP project itself.
Due to the completeness of the USBIP protocol document, we have not yet understood its role in the Bulk transmission process, which may also lead to errors in subsequent processes.
We will continue to try to make it work on USB HID. Once the USBIP problem is solved, we will immediately transfer it to work on WinUSB
Credits to the following project, people and organizations:
- https://www.github.com/windowsair/wireless-esp8266-dap origin of this project
- https://github.com/thevoidnn/esp8266-wifi-cmsis-dap for adapter firmware based on CMSIS-DAP v1.0
- https://github.com/ARM-software/CMSIS_5 for CMSIS
- https://github.com/cezanne/usbip-win for usbip windows