For using a dongle protected DOS application on Windows, there usually are drivers available that enable the classic NTVDM to interact with the HARDLOCK.SYS driver provided by Aladdin Knowledge Systems (now Safenet Inc.). As NTVDM usually is only supported on 32bit Windows versions, the driver that interacts with the DOS-applications is currently only available for 32bit Windows versions. Now that we have NTVDMx64, there is the need to interact with such Dongles also on 64bit Windows, but no driver is available from Safenet Inc. In order to remedy this issue, I created a driver and VDD component to allow interaction with the Dongle also on 64bit NTVDMx64. Unfortunately, due to technical reasons explained later, this has to be done in the form of a driver, unless you just want to emulate a simple dongle.
In case you use a very simple HASP dongle in your DOS application, you may already use a Dongle Emulator like HASPHL2007, Multikey or MkBus on your 32bit machine. If this is the case, you should also have a .reg file defining the dongle dump and it may be possible to emulate the dongle with UCLHASP functions. For instructions for creating a .reg file from your existing dongle (or from existing HASPHL2007 emulator), see here. In case the DOS application doesn't use the INT 6 (Invalid opcode) services for decryption of cypted code, it may be enough to use the Dongle usermode emulation. The advantage of this approach is that you don't have to install a driver on your 64bit machine and save you the hassle with possible instabilities of the original driver leading to sytem crashes and the driver signing problems discussed in the "full driver" installation instructions. If it doesn't work, you can always try the full driver variant.
If you are using classic NTVDM or NTVDMx64, using the emulator as VDD like described here is your best bet, because it will take the fewest amount of DOS memory and handles every HASP call directly in 32bit land. You are using the unmodified UCLHASP emulator for best stability. If you are planning to use the dongle with DOS emulators or even under plain MS-DOS on a real DOS-Machine, look down for the plain DOS UCLHASP emulator instead.
1) You need the NTVDMx64, of course 2) You must have added your emulator dongle dump .reg file to registry. Keys are searched in the following paths:
HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\Emulator\Hasp\Dump
HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\MultiKey\Dumps
HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Mkbus1) Download the uclhaspemu.zip from "Releases" and unpack it to a directory. 2) Run install.cmd in there, that should install the VDD and the emulator library
Instead of using NTVDM or NTVDMx64, you may want to use the UCLHASP emulator as a plain DOS device driver, thus enabling you to also use it on a bare-metal MS-DOS installation or in an emulator like DOSBOX-X. I ported UCLHASP code to a plain MS-DOS device driver for that. This should be compatible with most MS-DOS emulations (including NTVDM).
1) Ensure that you have a fully-working DOS emulator with support for device drivers reading full chunks of memory or a working plain MS-DOS. For DOSBox-X this was first implemented with pull request 3347, but was later broken with 3676 again, being fixed again in 3776, effectively meaning at the time of writing, only the August 01/2022 release is working, but Semptember 2022 release is broken. It is exepcted that the fix will be deployed in releases after October 2022, but at the time of writing, there was no release available yet.
2) The UCLHAPS.SYS driver takes an unencrypted Unidump-File as parameter, you need the file you created using h5dmp that you fed to UniDump2Reg to create a .reg file. This will contain the plain binary dongle dump that will be read by the driver. For a way to convert HASPHL2007 dongle dump to Unidump file, see link in chapter introduction. A common file size of such a dump file is 719 bytes for a MemoHASP.
NB: The HASP client code only talks to the driver if it thinks that it is running on NTVDM. This means that "real" DOS Version needs to be reported as version number 5.50. The UCLHASP.SYS driver therefore modifies Function 3306h of INT 21h to pretend being DOS 5.50. It has an extra measure to guess that it is asked by the HASP driver about the DOS-version but nevertheless, under some circumstances it could mean that your target application also thinks that it is running on NTVDM and possibly change its behaviour accordingly. Although the likelyhood is not very high, be aware that this could be a potential problem for malfunction of your application.
1) Download UCLHASP.SYS file from "Releases" and dump it to your DOS machine to a location where you can later load it.
2) Dump your Unidump file (let's name it HASP.DMP in this example) to some directory of you DOS-machine, so that you can pass its path and name as a parameter when loading the UCLHASP.SYS driver.
3) Make your DOS or DOS emulation load the UCLHASP.SYS on CONFIG.SYS with
DEVICE= command. Under plain DOS, this line has to go into CONFIG.SYS,
under NTVDM into CONFIG.NT and under DosBox-X into the section named
[config] in dosbox-x.conf.
Of course you have to specify correct paths in 8.3 format, if your
drivers aren't just in the root directory of your DOS System-driver
which this example assumes. As mentioned above, Unidump file's name is
assumed as HASP.DMP:
DEVICE=UCLHASP.SYS HASP.DMPThe DEVICE= statement should be at the bottom of your file/section so that the chance for interfering with DOS Version-checks for other drivers that may get loaded isn't high.
If you prefer, you could also load it with DEVLOAD.COM at runtime instead
The full driver tries to give NTVDM access to the real HASP driver running on your system, so this method is i.e. suitable for connecting a real physical key to your machine as well as using kernel mode emulators like i.e. MkBus, where 64bit drivers exist.
As it's nearly impossible nowadays to get a driver signing certificate for code signing, unfortunately, Windows usually has to be set into "Test signing mode" in order to load that driver, but as these stupid driver limitations are a problem for every Software writer, it may be better running a system in Test signing mode anyway.
However I found a code signing certificate on the Internet that currently works, so in the best case, the installation package just works out of the box. So there are 2 installation packages available, one that only works with test signing and one that got signed using mentioned certificate. You may first want to try the "signed" installer and only if it doesn't work (or your security solution prevents installation, cert got revoked or whatever might happen in the future), try the "testsigned" installer.
1) you need the NTVDMx64, of course. 2) you need the the 64bit hardlock driver. Unfortunately, in recent versions, the driver package doesn't include the hardlock.sys driver anymore, so please download the haspdinst.exe from the releases-Page of this repository instead! Install it using the following command:
haspdinst -i -ldThe -ld switch is important, so that the "legacy device" driver gets installed.
After successful installation of the dongle driver, continue with either
signed or unsigned driver, according to your needs. It is recommended to
first try the signed installer.
1) Download the haspnt64-signed.zip from "Releases" and unpack it to a directory. 2) Run install.cmd in there, that should install the driver and VDD
OR
1) Put your system into test signing mode by issuing the following command on an elevated command prompt as admin:
bcdedit /set testsigning onIf it doesn't work and you get an error, i.e. Secure Boot preventing you from enabling test signing, refer to this guide on how to enable test signing using the boot menu. 2) Download the haspnt64-testsigned.zip from "Releases" and unpack it to a directory. 3) Run install.cmd in there, that should install the driver and VDD
OR
In order to know, what the installer does, here is a short description of the steps being carried out by the installer. Normally, you don't need this.
1) For the testsigned installer, refer to Step 1 of 2b)
2) Install the haspnt64.cer as Trusted publisher into your local certificate
store:
certutil -addstore "TrustedPublisher" haspnt64.cerThis is crucial, otherwise the driver won't load. Be aware that these are
completely different certificates in signed and testsigned installer.
3) Install the haspnt64.inf either by rightclicking on the haspnt64.inf and
select "Install" or by issuing the following command:
rundll32 setupapi,InstallHinfSection DefaultInstall 132 .\haspnt64.inf4) After the system driver has been installed successfully, you need to load
the DOS driver on startup of NTVDM. So add the following line to your
Windows\SysWOW64\config.nt file :
device=%SystemRoot%\system32\haspdos.sys5) Now start the Windows driver that does the communication with the VDD:
net start haspntLet's start from the lowest level to the highest.
| Level | Caller | Interface |
|---|---|---|
| DOS | Application | Calls DOS Device driver HASPDOSDRV via INPUT (read) |
| DOS | HASPDOS.SYS | Calls HASPVDD interface via BOP (VDDDispatch) |
| NTVDM | HASPVDD.DLL | Calls \\.\Hasp device via ReadFile call |
| KERNEL | HASPNT.SYS | Calls \Device\FNT0 via intl. HASP_IOCTL_DOS_DISPATCH |
| KERNEL | HARDLOCK.SYS | Operates the dongle |
Now some more details for every layer:
The end user application gets linked with some HASP library that does the
interfacing either directly with the dongle or on Windows NT with the
HASPDOS.SYS driver. Reason is that there is no direct port access to the
hardware Dongle on Windows NT.
The detection of NTVDM works via the system call to get the DOS version
(Function 3306h of INT 21h).
If the version number is 5.50 (BX=3205h), NTVDM is assumed and the
HASPDOSDRV driver gets called via the standard DOS device driver read
routines (Function 3Fh of INT 21h).
The speciality is that the read buffer gets loaded with a command
structure and then receives the reply in this command structure.
It basically puts the register contents from the caller into that buffer
and receives the reply in the very same buffer.
For a documentation on how this buffer may look like, see
HaspDOSBufferStruc in haspintl.h.
For a documented disassembly of the DOS HASP code, see the IDA DB of
HASP Emulator v0.10d.
Here is a table of some basic DOS HASP functions:
+--------------------+--------------------+----------------------------------+
| SERVICE | CALL | RETURN |
| BH=FUNC, BL=PORT | | |
+--------------------+--------------------+----------------------------------+
| 1. | | AX : 0 - HASP NOT FOUND |
| ISHASP | | 1 - HASP FOUND |
+--------------------+--------------------+----------------------------------|
|2. | AX=SEEDCODE | AX : 1ST RETURN CODE |
| HASPCODE | CX=PASSWORD 1 | BX : 2ND RETURN CODE |
| | DX=PASSWORD 2 | CX : 3RD RETURN CODE |
| | | DX : 4TH RETURN CODE |
+--------------------+--------------------+----------------------------------+
|3. | CX=PASSWORD 1 | BX : DATA |
| READMEMO | DX=PASSWORD 2 | CX : STATUS |
| | DI=MEMORY ADDR. | (READ 1 byte at DI) |
+--------------------+--------------------+----------------------------------+
|4. | CX=PASSWORD 1 | CX : STATUS |
| WRITEMEMO | DX=PASSWORD 2 | |
| | DI=MEMORY ADDR. | |
| | SI=MEMORY DATA. | |
+--------------------+--------------------+----------------------------------+
|5. | CX=PASSWORD 1 | AX : MEMORY SIZE |
| HASPSTATUS | DX=PASSWORD 2 | BX : HASP TYPE |
| | | CX : ACTUAL LPT_NUM |
+--------------------+--------------------+----------------------------------+
|6. | CX=PASSWORD 1 | AX : IDLOW |
| HASPID | DX=PASSWORD 2 | BX : IDHIGH |
| | | CX : STATUS |
+--------------------+--------------------+----------------------------------+
|32h. | CX=PASSWORD 1 | CX : STATUS |
| READBLOCK | DX=PASSWORD 2 | |
| | DI=MEM.START ADDR.| |
| | SI=BLOCK LENGTH | |
| | ES=BUFER SEG. | |
| | AX=BUFER OFFS. | |
+--------------------+--------------------+----------------------------------+
|33h. | CX=PASSWORD 1 | CX : STATUS |
| WRITEBLOCK | DX=PASSWORD 2 | |
| | DI=MEM.START ADDR.| |
| | SI=BLOCK LENGTH | |
| | ES=BUFER SEG. | |
| | AX=BUFER OFFS. | |
+--------------------+--------------------+----------------------------------+The DOS device driver must be loaded via the CONFIG.NT file (NTVDM variant of CONFIG.SYS). This is done via DEVICE= statement:
device=%SystemRoot%\system32\haspdos.sysThe device driver flags indicate a character device driver that goes by
the name HASPDOSDRV. In its initialization routine, it registers an
INT 2f Multiplexter Interrupt
handler for the function 5000h. When called, it returns some magic numbers
in register AX-DX. The purpose is currently unknown, maybe some kind of
additional installation check?
Besides that, it uses handler for OPEN, CLOSE and INPUT (read).
On OPEN, it registers with the HASPVDD.DLL via well-known BOP interface.
The init-function is VDDRegisterInit, the Dispatch-function is
VDDDispatch.
On CLOSE, it unregisters itself and on INPUT, it passes on the buffer
to the VDD. On error, the errorcode 8003h is being set.
Pretty straighforward.
You can see my sample implementation of the DOS driver in the
haspdos directory in files HASPDRV.INC
and HASPDOS.ASM.
You can compile and link them via TASM.
c1.bat shows how to compile and link it. You need exe2bin to convert it
to a .sys file.
As mentioned before, this driver includes the dispatch routines driven by the
HASPDOSDRV driver. The dispatch routine gets the pointer in ES:DI and a count
in CX and then calls its internal CALLVDDHASP routine with this as
parameters. Interestingly, there also is an unused routine called
CALLNEWVDDHASP in it, which would pretty much resemble the interface we get
to know later in the next driver HASPNT.SYS. However, the routines that are
called by HASPNT.SYS into HARDLOCK.SYS, which would be pretty much the
structure of the CALLNEWVDDHASP call is a IRP_MJ_INTERNAL_DEVICE_CONTROL
routine, so it cannot be called from the VDD and thus we can forget about it.
Anyway, the CALLVDDHASP routine first decodes the "encrypted" buffer it got
passed. For the encryption and decryption scheme, either see the
Decrypt28 routine in haspio.c for a C implementation or
the HASPEMU.ASM for an assembler implementation
(stolen from UCLHASP).
UCLHASP implementation had a bug of not initializing tmp_decrypt buffer
properly, this has been fixed here.
If there is a buffer to be transferred from DOS memory to the driver, it
translates the DOS pointer to a memory address readable by the driver and then
re-encrypts the buffer again (as DOS addresses cannot be directly mapped without
translation).
It opens a handle to the next driver in chain that is listening to the device
path \\.\HASP. Then it calls the ReadFile
API on the local buffer it copied from DOS and by doing so calls the next driver
which takes the input buffer, and places the result in the same buffer as output.
For an example, see the CallLegacyHardlock function in the
hardlockdrv.c.
The driver exposes mentioned device node \\.\HASP and is classified as a
parallel port driver.
On initialization, it opens a device handle to the downlevel HARDLOCK.SYS
device node \Device\FNT0. It then sends an initialization request IRP
HASP_IOCTL_DOS_INITIALIZE to it, so that it reads its settings from the
registry for processing incoming packets. Please note that I made the IOCTL
names up, but the IOCTL codes are the important part. For IOCTLS, see
hardlock.h.
It is listening for IRP_MJ_READ requests and decrypts the passed-in buffer
via the previously mentioned decryption routines. It then converts to buffer
to a driver-internal format which is documented as
HaspWinBufferStruc in haspintl.h. It mainly consists
of 3 operation codes (see function Convert28ToHL in haspio.c),
a packet length of the whole struct, a packet length of the payload struct,
the payload buffer (passed in DOS-buffer except the first 4 bytes + 4 byte
padding), followed by the length of a potentially encoded memory buffer
following the structure on certain opcodes that requires such, as well as
segment and offset addresses AX:ES, both in the pointer size native to the
architecture of the target system, so the architecture of the driver.
As mentioned, payload can follow or not.
For a better understanding, have a look at haspio.c.
This converted buffer structure then gets passed down to HARDLOCK.SYS driver
via IOCTL HASP_IOCTL_DOS_DISPATCH. The bad thing about this IOCTL is,
that it is - as previously mentioned - a IRP_MJ_INTERNAL_DEVICE_CONTROL
control code, so it cannot be accessed by a usermode application (which
would normally work fine and also was attempted by the not-used
CALLNEWVDDHASP function in HASPVDD.DLL), so it is mandatory to implement
a driver to access this IOCTL code unfortunately. HASPNT.SYS driver
unfortunately cannot be bypassed.
This is just for the workflow of the HASPVDD.DLL incoming data packets, the driver offers far more functionality, but it's not intersting to us for our usecase.
The HARDLOCK.SYS driver is the core of the whole process, taking IOCTLS from the callers and create a request to the dongle from the passed-in buffer structure. It has to be said that there are multiple possible structures and the structure here is not the only one being used.
This is just for the workflow of the HASPVDD.DLL incoming data packets, the driver offers far more functionality, but it's not intersting to us for our usecase.
The drivers implemented here have a focus on stability and on the shortest code path. Therefore, i.e. translation functions that are normally in HASPNT.SYS have been transferred to usermode HASPVDD.DLL driver, as it eliminates potential bugs and crashes in the driver that can cause BSODs or hangs. So let's walk down the call chain of our drivers and see, which options you have on the path.
This one is mandatory so that your DOS application has a connection point to the upper level drivers. The driver comes in 3 flavours:
1) The reimplemented HASPDOS.SYS driver that communicates with HASPVDD.DLL
2) A HASPEMU.SYS emulation driver that just does a "replay" on packets of
Calltype #2 (HASPCODE) for very dumb applications.
3) A UCLHASP.SYS driver that emulates a MemoHasp in plain DOS given a
UniDump file.
The driver isn't really needed to be built yourself, just take the original HASPDOS.SYS and you are good to go. There are no modifications in the workflow compared to the original driver (only a few code optimizaions). The driver is just there for illustration purposes so that you have a commented version and see what it is basically doing. The driver only works in NTVDM, as it uses the well-known BOPping mechanism to call the VDD (see isvbop.inc).
As UCLHASP emulation method offers more functionality, this method is not recommended anymore and this chapter just stays here for reference purposes:
I also wrote a simple Dongle emulator for Call #2 (HASPCODE).
This is for pretty stupid applications that just check the presence of the
dongle by always using the same seed and the same passwords and just compare
the return value.
To get it working, you can sniff the communication with the dongle via
a normal setup with using HASPVDD.DLL (so as a first step, you have to
do a normal setup with HASPDOS.SYS driver and HASPVDD and then you can later
shortcut it by just using HASPEMU.SYS skipping the rest of the drivers in
chain when you know the valid responses the driver has to send). By using
DebugView
you can see the communcation between the dongle and the application.
Should there always be command 2 with the same Param1..4 and the result is
always the same in 1..4, you can write down these 4 values as hex and then
just install the device driver with
device=%SystemRoot%\system32\haspemu.sys <param1> <param2> <param3> <param4>instead of haspdos.sys.
param1..4 have to be in hex without a 0x prefix, i.e.:
device=%SystemRoot%\system32\haspemu.sys 1234 5678 9abc def0Be aware that the values are little endian (so read from right to left). Here is an example. Given an application that just checks for presence with call 1 and then always does the same HASPCODE, you get something like this on DebugView and can interpret it according to the table in haspintl.h:
________ [Ln] [ Ticks ] [Service ] [Param1/AX] [Param2/BX] [Param3/CX] [Param4/DX] [Para1R/DI] [Para2R/SI] [Para3R/ES] [Para4R/AX]
HASP OUT [28] AB 00 00 00 01 00 00 00 AD BA 00 00 00 00 00 00 EF BE 00 00 AD DE 00 00 00 00 00 00 00 00 00 00 00 00 00 00 AD BA 00 00
HASP IN [28] AB 00 00 00 01 00 01 00 01 00 00 00 01 00 00 00 00 00 00 00 AD BA 00 00 01 00 00 00 01 00 00 00 00 00 00 00 AD BA 00 00So let's interpret this:
Service: 1
Input parameters: Don't care
Returns:
AX = 1 - HASP FOUND
BX = 1 - Address of HASP dongle = 1
CX = 0 - SuccessNow for the next call (the one we are interested in):
________ [Ln] [ Ticks ] [Service ] [Param1/AX] [Param2/BX] [Param3/CX] [Param4/DX] [Para1R/DI] [Para2R/SI] [Para3R/ES] [Para4R/AX]
HASP OUT [28] C8 02 00 00 02 00 00 00 AD BA 00 00 00 00 00 00 EF BE 00 00 AD DE 00 00 01 00 00 00 01 00 00 00 00 00 00 00 AD BA 00 00
HASP IN [28] C8 02 00 00 02 00 02 00 34 12 00 00 78 56 00 00 BC 9A 00 00 F0 DE 00 00 34 12 00 00 78 56 00 00 BC 9A 00 00 F0 DE 00 00Interpreted:
Service: 2
Input parameters:
AX = BAAD = Seed code
CX = BEEF = Password 1
DX = DEAD = Password 2
Returns:
AX = 1234 = Return code 1
BX = 5678 = Return code 2
CX = 9ABC = Return code 3
DX = DEF0 = Return code 4So in this case, you have to load the device driver with the parameters mentioned in the example above (just put ax, bx, cx, dx results seperated by blanks in hex as parameters).
There also is a DEVLOAD.COM in the haspdos directory which allows you to load it afterwards and only on demand instead of everytime in config.nt at start:
devload haspemu.sys 1234 5678 9abc def0This is a port of the UCLHASP driver from 32bit Windows to MS-DOS. As the UCLHASP driver was implemtend in 32bit assembly, it was eligible for porting to plain DOS. However, a few modifications needed to be made and a loader code had to be written in order to read a Unidump file with the data to present to the calling application, as naturally there is not Registry on MS-DOS from where to load the dump data. Thus, there is a seperate uclhasp subdirectory under haspdos that contains the modified code (whereas the original code (with decoding bugfix, but rest is original) resides in uclhasp\asm\src directory).
As mentioned above, the driver has to fake the MS-DOS version number returned so that the NTVDM-code of the HASP interface can kick in (which is done via INT 21h hook that it places on load). Code to do this is provided in the FAKEDOS?.INC files whereas H is header part (resident part) and F is footer part (only used upon load and thus can be discarded).
During testing on real DOS, it was noticed that there was always a machine lockup upon opening the driver with its devicename HASPDOSDRV. This is due to a misconception of the driver written by the HASP authors that goes unpunished on Windows NT, but will lock up plain MS-DOS: For some unknown reason, they thought that the driver name can be 10 chars, whereas only 8 characters for a device name are valid in the device driver header. This doesn't seem to be an issue in NTVDM DOS, but on plain DOS 6.22, DOS just locks up when using a device name with over 8 chars on OPEN call (see MS-DOS Kernel dir2.asm routine ChkDev). Therefore the INT 21h hook is also checking this and shortening the device name to 8 chars in case it gets "HASPDOSDRV" string in Function 3Dh of INT 21h (file open). The driver's code is also split in header (UCLHASPH.ASM) and footer (UCLHASPF.ASM) distinguishing resident and the loader code to save memory. The driver has been tested on DosBox-X and NTVDMx64 and plain DOS 6.22.
Unlike the original implementation, the driver has multiple operation modes that can be controlled by registry keys.
Unlike the original HASTNT.SYS driver, the driver from this package offers
a direct means of communication via HASP_IOCTL_DOS_DISPATCH IOCTL code,
so the same that gets used by the underlying HARDLOCK.SYS driver, but
packets have to be forwarded due to the limitation of this being an
internal IOCTL, as previously mentioned. This basically resembles the
CALLNEWVDDHASP interface. The advantage is that all processing and
preparation of the expected buffer is being done in usermode by the
HASPVDD.DLL driver so that potential crashes don't make the whole system
unstable. The call itself can be seen in CallHardlock function in
hardlockdrv.c.
NOTE: This interface is NOT compatible with the original HASPNT.SYS
driver!
This is mainly useful for logging purposes on a 32bit system where you
installed the normal HDD32 device driver 4.102.5.22 from Aladdin.
With the help of this mode, you can play man-in-the-middle and sniff the
calls to the underlying dongle. For this, just replace the original
HASPVDD.DLL driver with this one and set the following registry keys
in HKEY_LOCAL_MACHINE\System\CurrentControlSet\Services\HaspNt\Parameter:
+--------------------+-----------+--------+
| Key Name | Type | Value |
+--------------------+-----------+--------+
| LegacyVDDInterface | REG_DWORD | 1 |
+--------------------+-----------+--------+When enabled, you can see the calls being sent and received from and to the dongle via DebugView. If you want to record the calls and check them later, you can set the following key to log them into a binary logfile:
+--------------------+-----------+-----------------------------------------+
| Key Name | Type | Value |
+--------------------+-----------+-----------------------------------------+
| LogFile | REG_SZ | Full path and name of a file to log to. |
| | | i.e. C:\Temp\hasplog.dmp |
+--------------------+-----------+-----------------------------------------+The logged calls can then be later dumped in human readable form by the dumplog utility.
As UCLHASP emulation method offers more functionality, this method is not recommended anymore and this chapter just stays here for reference purposes:
As prevously mentioned, there may be applications where it is sufficient to just return static values to the 02 request. See chapter about the HASPEMU.SYS driver for details. This is basically the same facility, but you don't need a seperate HASPEMU.SYS driver, but can use the normal HASPDOS.SYS driver and just let the HASPVDD.DLL driver do the emulation. The reason that there are 2 ways to accomplish the same goal is that the HASPEMU.SYS driver may also work with other DOS emulations or even directly in good old plain DOS, whereas the HASPDOS.SYS driver only works in conjunction with NTVDM. If you can emulate the dongle using this method, you don't need the HASPNT64.SYS driver, as the function calls are directly answered by the HASPVDD.DLL driver and no more calls down the chain are necessary. So in short, the shortest path is to use HASPEMU.SYS, the second shortest path is to use this emulation interface (HASPDOS.SYS + HASPVDD.DLL).
So the first step to use this (if the target application is suitable for
this sort of emulation which I doubt many applications are) is to sniff the
traffic between the application and the dongle by using before mentioned
ReadFile based interface and gather the logs from it.
When you have captured the call, you need to create a registry key named
EmulateParams that contains the binary representation of the expected
answer from Param1-4.
Using the example from HASPEMU.SYS driver, say, you have this static reply
from the dongle:
________ [Ln] [ Ticks ] [Service ] [Param1/AX] [Param2/BX] [Param3/CX] [Param4/DX] [Para1R/DI] [Para2R/SI] [Para3R/ES] [Para4R/AX]
HASP OUT [28] C8 02 00 00 02 00 00 00 AD BA 00 00 00 00 00 00 EF BE 00 00 AD DE 00 00 01 00 00 00 01 00 00 00 00 00 00 00 AD BA 00 00
HASP IN [28] C8 02 00 00 02 00 02 00 34 12 00 00 78 56 00 00 BC 9A 00 00 F0 DE 00 00 34 12 00 00 78 56 00 00 BC 9A 00 00 F0 DE 00 00You now take Param1-Param4 reply, that would be the following 16 bytes:
34 12 00 00 78 56 00 00 BC 9A 00 00 F0 DE 00 00
So you create a registry value EmulateParams with these 16 bytes under
HKEY_LOCAL_MACHINE\System\CurrentControlSet\Services\HaspNt\Parameter,
set LegacyVDDInterfaceto 2 and if will start emulating it.
To end emulation, delete the keys.
+--------------------+-----------+------------------------------------------+
| Key Name | Type | Value |
+------------------- +-----------+------------------------------------------+
| EmulateParams | REG_BINARY| Binary dump of Param1..4 response from |
| | | Dongle call 2 to respond with. Has to be |
| | | exactly 16 bytes long (4 * 4) |
+--------------------+-----------+------------------------------------------+
| LegacyVDDInterface | REG_DWORD | 2 |
+--------------------+-----------+------------------------------------------+As mentioned in the introduction, it's always desirable to do as much in usermode as possible and not having to use kernel mode drivers saves you from potential problems. Therefore it is preferrable to do a usermode dongle emulation for dongles that just use simple functions and where the UCLHASP emulator may be enough.
For this reason, the HASPVDD driver supports the use of a "plugin" DLL
that offers emulation functions. The driver just has to export the function
CallHardlock that simply gets called whenever there is a call from the DOS
driver and is expected to handle it accordingly. For a prototype definition,
see uclhasp.c.
The emulator registers itself with HASPVDD by creating the registry value
EmulatorDLL with a path to the driver under
HKEY_LOCAL_MACHINE\System\CurrentControlSet\Services\HaspNt\Parameter,
therefore to use uclhasp (given that uclhasp.dll is present in the
Windows\SysWOW64 directory), the following entry has to be made:
+--------------------+-----------+------------------------------------------+
| Key Name | Type | Value |
+------------------- +-----------+------------------------------------------+
| EmulatorDLL | REG_SZ | uclhasp.dll |
+--------------------+-----------+------------------------------------------+To unregister the emulator, just remove the key again and then it will talk to the normal HASP driver again.
The UCLHASP driver searches for dongle key definitions in the following registry paths:
HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\Emulator\Hasp\Dump
HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\MultiKey\Dumps
HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\MkbusThe key format is like the one specified for these emulators, so it should work out of the box.
Citing the UCLHASP documentation (as an example):
All dumps are contained in the registry along the path
HKEY_LOCAL_MACHINE\System\CurrentControlSet\Services\Emulator\HASP\Dump\xxxxxxxx
where xxxxxxxx - key opening passwords (must be 8 digits!).
DemoMA key registry example (3c39:25a0)
REGEDIT4
[HKEY_LOCAL_MACHINE\System\CurrentControlSet\Services\Emulator\HASP\Dump\3c3925a0]
"Name"="DemoMA dongle"
"Internal Name"="[DemoMA]"
"SN"=dword:DEADBEEF
"pwd"=dword:3c3925a0
"Type"=dword:01
"Memory"=dword:01
"Data"=hex:ff,ff,ff,ff,ff,ff,ff,ff,ff,ff,ff,ff,ff,ff,ff,ff,ff,ff,ff,ff,ff,ff, \
ff,ff,ff,ff,ff,ff,ff,ff,ff,ff,ff,ff,ff,ff,ff,ff,ff,ff,ff,ff,ff,ff,ff,ff,ff, \
ff,ff,ff,ff,ff,ff,ff,ff,ff,ff,ff,ff,ff,ff,ff,ff,ff,ff,ff,ff,ff,ff,ff,ff,ff, \
ff,ff,ff,ff,ff,ff,ff,ff,ff,ff,ff,ff,ff,ff,ff,ff,ff,ff,ff,ff,ff,ff,ff,ff,ff, \
ff,ff,ff,ff,ff,ff,ff,ff,ff,ff,ff,ff,ff,ff,ff
"Created"="12/12/1998 6:59 PM"
"Copyright"="(c)1998 by MeteO //UCL dongle labs"
"Expired"=dword:1dae282
"CRC"=dword:00000000Main fields used:
SN - key serial number
Pwd - open key passwords
Data - contents of the dongle memoryThese have to go into the following Registry path:
HKEY_LOCAL_MACHINE\System\CurrentControlSet\Services\HaspNt\Parameter
+--------------------+-----------+-------------------------------------------+
| Key Name | Type | Description |
+--------------------+-----------+-------------------------------------------+
| LegacyVDDInterface | REG_DWORD | Val | Description |
| | | --- | ----------------------------------- |
| | | 0 | Use IOCTL based interface |
| | | 1 | Use Legacy ReadFile based interface |
| | | 2 | Emulate calls only (EmulateParams) |
+--------------------+-----------+-------------------------------------------+
| ErrorReportingMode | REG_DWORD | Val | Description |
| | | --- | ----------------------------------- |
| | | 0 | Show MessageBox on fatal error |
| | | 1 | Write them only to Debug Console |
| | | 2 | Do not display them at all |
+--------------------+-----------+-------------------------------------------+
| LogFile | REG_SZ | Specify path and filename of the file to |
| | | log all dongle traffic to. The file can |
| | | then be fed into dumplog to show the calls|
+--------------------+-----------+-------------------------------------------+
| EmulateParams | REG_BINARY| Binary dump of Param1..4 response from |
| | | Dongle call 2 to respond with. Has to be |
| | | exactly 16 bytes long (4 * 4) |
| | | Only applies to LegacyVDDInterface = 2 |
+--------------------+-----------+-------------------------------------------+
| EmulatorDLL | REG_SZ | DLL to register with driver to do dongle |
| | | Emulation. Disables normal operation and |
| | | dispatches every call to emulator DLL. |
| | | Do NOT confuse with LegacyVDDInterface=2! |
+--------------------+-----------+-------------------------------------------+As you may have realized, the HASPVDD.DLL driver has a Release and a
Release64 build configuration setting, but only allows x32 architecture. The
reason for this is pretty clear: As NTVDM is always a 32bit application, even
NTVDMx64 on 64bit machines, it expects all the modules it loads to also be
32bit modules. Now why is there a Release64 configuration then? As previously
mentioned, the underlying HARDLOCK.SYS driver on a 64bit system is 64bit and
therefore it expects the internal buffer to contain 2 64bit values in the end.
See the BufferOffset and BufferSegment members of the HaspWinBufferStruc
in haspintl.h.
So you need a different HASPVDD.DLL on 64bit than on 32bit.
However this isn't really a problem, if you just use the HASPVDD.DLL driver
for monitoring/sniffing HASP traffic on a 32bit system, as you have to use
the ReadFile based I/O interface to interact with the original HASPNT.SYS
driver anyway and thus, HASPVDD.DLL doesn't generate any internal packages
itself, but relies on the underlying HASPNT.SYS driver to generate them.
So, when you build this driver, use the Release64 configuration and you
should be fine. Should you want to not use the original HASPNT.SYS on a 32bit
system, but use our HASPNT64.SYS (it actually IS possible to compile it for
x86 and maybe you want to use it due to stability issues that can be seen
with the original driver), you have to take care of the different build
configurations for HASPVDD.DLL, if you want to use it in conjunction with
our own HASPVDD.DLL. But be aware, that we ONLY support DOS applications!
Regarding the UCLHASP driver, it contains the ASM source in asm\src. The source can only be compiled with TASM, not with MASM, therefore the .asm files cannot be directly linked with Visual Studio, which would use integrated MASM. So the object files are linked to the project instead. To generate the object files, use TASM. However TASM outputs OMF object format, not COFF and newer Microsoft linkers and even the editbin utility in more recent Visual Studio Versions (like VS2019) do not seem to support OMF anymore, no idea, why that got removed. So in order to link the .obj files with newer VS versions, they first need to be converted to COFF via Visual Studio 6 version of editbin which still supoprts OMF. The MAKE.BAT in asm-Directory does that for you. To make the project compilable out of the box for you, the repository therefore contains .obj files of UCLHASP.
The driver should theoretically also expose the same ReadFile based interface
as the original HASPNT.SYS driver has, but it has not been thouroughly tested.
It poses the risk of data processing in kernel and thus should be avoided in
favour of the IOCTL based interface that our HASPVDD.DLL driver uses per
default.
The driver is listening for the HASP_IOCTL_DOS_DISPATCH IOCTL and dispatches
the call via IRP_MJ_INTERNAL_DEVICE_CONTROL to the HARDLOCK.SYS driver.
Be aware that on 64bit systems, the underlying HARDLOCK.SYS driver expects
its previously documented internal structure with 2 pointers as 64bit values,
so if using this interface, the upper-level HASPVDD.DLL has to take care of
this (see previous chapter).
Be aware that the HASPNT64.SYS driver is not identical to the original
HASPNT.SYS driver, which exposes a lot more interfaces to the callers. So
the driver really is just meant to be used for DOS support, other callers that
rely on different HASPNT.SYS interface or even packet sizes won't work with
it. It is possible to compile and run this driver on a x86 32bit system, for
details see previous chapter.
The driver requires to have a working 64bit HARDLOCK.SYS driver on the system, see Prerequisites section from installation instructions for details.
With this package, you get a well-documented example for the workflow of HASP dongles for applications running on DOS on Windows NTVDM. These drivers allow you to run HASP Dongle protected applications on NTVDMx64 on 64bit Windows the same as they would run natively on 32bit Windows and is therefore a useful extension for NTVDMx64 in order to run Dongle-Protected commercial DOS applications.
For questions, please use the Issue Tracker or other Github facilities.