Closed Seiler270 closed 8 years ago
luc-github
commented
8 years ago replacing variant.cpp is mandatory, please check FAQ : https://github.com/luc-github/Repetier-Firmware-0.92/issues?utf8=%E2%9C%93&q=is%3Aclosed+label%3AFAQ+ and this https://github.com/luc-github/Repetier-Firmware-0.92/issues/175#issuecomment-239762985
Seiler270
commented
8 years ago Thanks for the fast reply!
I understand that replacing the variant.cpp is important..
but WHERE does it go..
I read the link you posted and it is not quite the same issue, its backward.
I know where the variant.cpp file is in the repetier folder...
It says to REPLACE the file, where is the one that needs to be replaced? there is NOT a variant.cpp file under C:\Program Files (x86)\Arduino\hardware\arduino\avr\variants.. which is where I expected to find it..
luc-github
commented
8 years ago that is why I sent you links, variant.cpp is not in program files but users files - please read carefully BOTH links content
Seiler270
commented
8 years ago I read it
Stupid windows was hiding the DIR.
I got everything moved, flashing now.
It flashed fully and is now verifying, but its hanging out on 89%, ill give it a bit longer but I think I remember reading something about this.
luc-github
commented
8 years ago Yes it is FAQ too
Seiler270
commented
8 years ago Well it just stayed at 89% for several minutes so I closed arduino and shut the printer off.
powered it back on and there are no longer any black bars, just a blank screen.
I tried to reflash again with verify disable and it went through and said CPU reboot, but still nothing..
nothing whatsoever.
Seiler270
commented
8 years ago ok so now i cant jumper it back to black bars...
All i get is a completely blank screen, nothing else.
read the verification issue FAQ, none of the listed reasons make sense with my issue.
Nothing is wrong with my USB cable, Im not running VMware. and the jumper is not left in place.
Im not getting a verification FALED message, it just stuck at 89%
Seiler270
commented
8 years ago just ran it again with verification on, it went through just fine.
still just a blank screen, no activity.
Seiler270
commented
8 years ago Out of ideas.
The program can still see the board, so I guess there is hope.
However i cannot get it back to where it was before the last flash, where there are the black bars on the screen.
Seiler270
commented
8 years ago Well i started from scratch and did the whole process over again.
Everything exactly followed to the T
Verify successful done in 27.543 seconds Set boot flash true CPU reset.
nothing, blank screen.. thats it...
so... ***
Seiler270
commented
8 years ago the printer shows up under device manager as Arduino Due... so... its there but still nothing
Seiler270
commented
8 years ago Ok so it works.. sort of..
The screen doesent display anything.
Repetier host can see the printer, and tries to print but gives me an error that temp was raised too slow.
I can muddle my way through the rest I think, but I would really like to get the screen to show something
luc-github
commented
8 years ago do you have a 2.0 or a 2.0A ? (2.0 = normal SD, 2.0A =micro SD)
Do you see EEPROM.bin from repetier SD card management? if yes delete it and power off printer, if no remove SD card and delete EEPROM.BIN from PC
Seiler270
commented
8 years ago I have the 2.0A with the micro SD
Where am I looking for these files? in the arduino program?
luc-github
commented
8 years ago On SD card
Seiler270
commented
8 years ago Ok deleted EEPROM.BIN from the printer's SD card, reinsalled card and turned on printer.
nothing..
reflash?
luc-github
commented
8 years ago what means nothing ?
Seiler270
commented
8 years ago the printer does nothing, no beeps no light nothing.
luc-github
commented
8 years ago yes seems flash is not done properly somehow
Seiler270
commented
8 years ago ok ill do it again
Seiler270
commented
8 years ago Reflashed.
Same issue
No image on screen.
When trying to print the bed heats up but the extruders never do and it kicks back the error saying
fatal: heator/sensor failure printer stopped and heaters disabled due to this error.
I did notice one thing,
when I go to print It says: Select Extruder 0 instead of 1 or 2.. is that maybe part of the problem with the heating?
luc-github
commented
8 years ago As you cannot see screen you cannot load fail-safe settings but did you send M502/M500 instead as write in readme ?
Seiler270
commented
8 years ago Yes, and when I did the printer light came on.
luc-github
commented
8 years ago and you should have sound when press home button right ?
Seiler270
commented
8 years ago Yes it beeps
luc-github
commented
8 years ago so better than no light no sound like before
what did you change in configuration.h for your printer ?
Seiler270
commented
8 years ago Just the definitions at the beginning
Define Davinci Model.
I set Davinci to 3 Model to 1
luc-github
commented
8 years ago No, 2.0A does not have SHARED_EXTRUDER_HEATER, it has 2 extruders each one using one heater
All I can see until now, it is that you do not follow strictly what it is mentioned in readme / https://github.com/luc-github/Repetier-Firmware-0.92/issues/175#issuecomment-239762985
I suggest you to remove all arduino files/ delete FW files reinstall arduino 1.6.9 / due 1.6.8 and FW and slowly / carefully follow each step of readme or https://github.com/luc-github/Repetier-Firmware-0.92/issues/175#issuecomment-239762985
As I cannot imagine others change you may have done to get the lcd not working, I really suggest you to stick to what is written as you seems to do others changes on your own that affect the fw which work on others 2.0A - this is the best advice I can give
Seiler270
commented
8 years ago will start over again.
Seiler270
commented
8 years ago Ok Im typing this as I do it, so I make sure I dont miss anything.
Turn off printer Remove SD card from printer and delete EEPROM.BIN from card
Reinstall SD card and power printer on.
No pic on screen, no lights no sounds.
Install arduino-1.6.9-windows Install complete
Open arduino
Select arduino AVR boards version 1.6.12 as shown is your picture. Install
Select arduino SAM boards 1.6.8 as shown in your picture. Install
Close arduino
Open Folder: Repetier-Firmware-0.92-master
Navigate to: \src\ArduinoDUE\AdditionalArduinoFiles\Arduino - 1.6.9 -Due 1.6.8\Arduino15\packages\arduino\hardware\sam\1.6.8\variants\arduino_due_x
Copy variant.cpp
Navigate to: C:\Users\User\AppData\Local\Arduino15\packages\arduino\hardware\sam\1.6.8\variants\arduino_due_x
Paste variant.cpp in dir, replace existing file.
Printer on, USB connected, correct Com port verified, good connection
Open arduino
Select Tools
Board
Select arduino Due (Native USB port)
Select Port COM6 (arduino native USB)
from arduino file menu open \Repetier-Firmware-0.92-master\src\ArduinoDUE\Repetier Repetier arduino file.
File loaded.
Select Configuration Tab
No other changes made,
Select Verify
Message: const int8_t sensitive_pins[] PROGMEM = SENSITIVE_PINS; // Sensitive pin list for M42
Done compiling
Select UPLOAD
Upload complete, Verifying
Verify successful done in 42.156 seconds Set boot flash true CPU reset.
Reboot printer
No image on screen at this point
Close arduino
Install repetier Host
Install repetier Server
Launch repetier host.
COnnect to printer via COM 6
Sent M502, then M500
Printer light turns on printer beeps when pressing home button.
Adding more shortly
Seiler270
commented
8 years ago Disconnect from printer
Start local server
open server front end
add printer
select correct com port
Connection success
retrieving info from firmware complete
Step 4
Number of extruders: 2 Filiment diameter 1.75
heated bed installed yes
step 5 features Fan installed: no SDCard reader: yes Software power: no
FINISH
Select printer, control from server
Test heated bed: good
Test Extruder 1: extruder does not heat
Test Extruder 2: extruder does not heat
Fatal Error: heater sensor failure message
Screen still blank
Return to host
Connect to printer VIA repetier server
load object to print
slice with slicer
select print
Heating bed:
Bed heats to 70c
Heating Extruder 1
Extruder never heats, get sensor fail error.
Log shows
12:46:30.373 : FIRMWARE_NAME:Repetier_0.92.10 FIRMWARE_URL:https://github.com/luc-github/Repetier-Firmware-0.92/ PROTOCOL_VERSION:1.0 MACHINE_TYPE:DaVinci EXTRUDER_COUNT:2 REPETIER_PROTOCOL:3
12:46:30.373 : Printed filament:0.00m Printing time:0 days 0 hours 0 min
12:46:30.373 : PrinterMode:FFF
12:46:30.420 : Error:M114
12:46:30.420 : X:NAN Y:NAN Z:NAN E:NAN
12:46:30.420 : DebugLevel:6
12:46:30.420 : SelectExtruder:0
12:46:30.436 : Begin file list
12:46:30.483 : ad_check_0002 1400
12:46:30.498 : Machine_Life.dat 14
12:46:30.498 : SAMPLE01.gcode 661731
12:46:30.498 : SAMPLE02.gcode 396439
12:46:30.514 : SAMPLE03.gcode 3669461
12:46:30.561 : last_temperature.txt 4
12:46:30.577 : offline_print.gcode 1425949
12:46:30.577 : eeprom.bin 4096
12:46:30.577 : End file list
12:46:30.623 : DebugLevel:6
12:46:30.623 : SelectExtruder:0
12:46:37.302 : Z jerk was too low, setting to 0.34
12:46:37.318 : SelectExtruder:0
12:46:37.334 : Info:Configuration reset to defaults.
12:46:43.601 : Info:Configuration stored to EEPROM.
12:48:27.415 : "C:\Program Files\Repetier-Host\plugins\RepetierServerConnector\RepetierServerStarter.exe" start
12:56:18.114 : Repetier-Server successfully connected.
12:56:18.353 : fatal:Heater/sensor failure Printer stopped and heaters disabled due to this error. Fix error and restart with M999.
12:56:18.353 : fatal:Heater/sensor failure Printer stopped and heaters disabled due to this error. Fix error and restart with M999.
12:56:19.027 : fatal:Heater/sensor failure Printer stopped and heaters disabled due to this error. Fix error and restart with M999.
12:56:20.017 : fatal:Heater/sensor failure Printer stopped and heaters disabled due to this error. Fix error and restart with M999.
12:56:21.009 : fatal:Heater/sensor failure Printer stopped and heaters disabled due to this error. Fix error and restart with M999.
12:56:21.999 : fatal:Heater/sensor failure Printer stopped and heaters disabled due to this error. Fix error and restart with M999.
12:56:22.991 : fatal:Heater/sensor failure Printer stopped and heaters disabled due to this error. Fix error and restart with M999.
12:56:23.979 : fatal:Heater/sensor failure Printer stopped and heaters disabled due to this error. Fix error and restart with M999.
12:56:25.081 : fatal:Heater/sensor failure Printer stopped and heaters disabled due to this error. Fix error and restart with M999.
12:56:26.073 : fatal:Heater/sensor failure Printer stopped and heaters disabled due to this error. Fix error and restart with M999.
12:56:27.066 : fatal:Heater/sensor failure Printer stopped and heaters disabled due to this error. Fix error and restart with M999.
12:56:28.041 : fatal:Heater/sensor failure Printer stopped and heaters disabled due to this error. Fix error and restart with M999.
12:56:29.047 : fatal:Heater/sensor failure Printer stopped and heaters disabled due to this error. Fix error and restart with M999.
12:56:30.038 : fatal:Heater/sensor failure Printer stopped and heaters disabled due to this error. Fix error and restart with M999.
12:56:31.033 : fatal:Heater/sensor failure Printer stopped and heaters disabled due to this error. Fix error and restart with M999.
12:56:31.522 : DebugLevel:6
12:56:31.522 : info:Continue from fatal state
12:57:48.453 : Starting object analyser ...
12:57:48.453 : Object is manifold.
12:57:48.453 : Analysing finished.
12:57:55.663 : Starting object analyser ...
12:57:55.663 : Object is manifold.
12:57:55.663 : Analysing finished.
12:57:58.962 : Slic3r command:C:\Program Files\Repetier-Host\Slic3r\slic3r.exe --load "slic3r_settings.ini" --print-center 100.00,100.00 -o "composition.gcode" "composition.amf"
12:58:01.176 :
So I m back to the same point, nothing on the screen, and the extruders wont heat.
Did I miss anything?
Seiler270
commented
8 years ago I posted this issue with the heating on the repetier forums and it was suggested that the correct heater output pin may not be selected.
But Im not sure where to look for that.
luc-github
commented
8 years ago I do not think it is the issue - it is working on other 2.0A see https://github.com/luc-github/Repetier-Firmware-0.92/issues/94 you can use same https://github.com/luc-github/Repetier-Firmware-0.92/releases/tag/v0.92.3.0 to verify the 0.92.10 is not broken for 2.0A which I doubt as it is working on 1.0A/AiO
About heating I guess more about hardware failure check https://forum.voltivo.com/showthread.php?tid=8517
EDIT: you can disable decouple test in configuration.h to check what is wrong
About screen, nothing = no backlight + no char or backlight + no char ?
Seiler270
commented
8 years ago trying the version you posted.
I highly doubt anything is wrong with the hardware considering everything was working perfectly just before flashing this firmware.
luc-github
commented
8 years ago what about screen ?
well short the davinci is easy - just use metal brush too strong cleaning noozle and it is done, another possiblity is connector loose - but this should be detected if disable decouple test allow to heat
Seiler270
commented
8 years ago The screen has not worked since i flashed this firmware.
setting FEATURE_DECOUPLE_TEST to 0 causes a failure to compile.
Extruder.cpp:409: error: 'isSensorDecoupled' was not declared in this scope
if(isSensorDecoupled())
luc-github
commented
8 years ago on which version of FW ?
Seiler270
commented
8 years ago luc-github
commented
8 years ago I guess you mean master branch based on 0.92.10 and not the link I gave you based on 0.92.3
I am checking now as did not test the decouple test with latest update - I may miss something
Seiler270
commented
8 years ago ill try that one with decouple disabled. one moment.
NOTE: the temperature sensors on the extrudes ARE working, and it shows the correct temp.
They wont heat.
Seiler270
commented
8 years ago trying now with the firmware you linked.
bed heats
then it shows 21:48:01.943 : Unknown command:N85 M107 then says heating extruder and just stays there, extruder never heats up.
Im still curious why it says "SELECTING EXTRUDER 0" instead of 1 or 2
luc-github
commented
8 years ago M107 unknow command is normal - Davinci does not allow fan control
can you share your begining part of GCODE code your are using for printing ? the part which set temperatures for extruders
what about screen ?
master is fixed for compilation - thanks for pointing out
luc-github
commented
8 years ago Repetier FW and Host use T0 and extruder 0 for first extruder and T1 and extruder 1 for second one
Seiler270
commented
8 years ago beginning part of GCODE when printing:
22:08:04.466 : OpenGL version:4.5.0 NVIDIA 372.54
22:08:04.466 : OpenGL extensions:GL_AMD_multi_draw_indirect GL_AMD_seamless_cubemap_per_texture GL_AMD_vertex_shader_viewport_index GL_AMD_vertex_shader_layer GL_ARB_arrays_of_arrays GL_ARB_base_instance GL_ARB_bindless_texture GL_ARB_blend_func_extended GL_ARB_buffer_storage GL_ARB_clear_buffer_object GL_ARB_clear_texture GL_ARB_clip_control GL_ARB_color_buffer_float GL_ARB_compatibility GL_ARB_compressed_texture_pixel_storage GL_ARB_conservative_depth GL_ARB_compute_shader GL_ARB_compute_variable_group_size GL_ARB_conditional_render_inverted GL_ARB_copy_buffer GL_ARB_copy_image GL_ARB_cull_distance GL_ARB_debug_output GL_ARB_depth_buffer_float GL_ARB_depth_clamp GL_ARB_depth_texture GL_ARB_derivative_control GL_ARB_direct_state_access GL_ARB_draw_buffers GL_ARB_draw_buffers_blend GL_ARB_draw_indirect GL_ARB_draw_elements_base_vertex GL_ARB_draw_instanced GL_ARB_enhanced_layouts GL_ARB_ES2_compatibility GL_ARB_ES3_compatibility GL_ARB_ES3_1_compatibility GL_ARB_ES3_2_compatibility GL_ARB_explicit_attrib_location GL_ARB_explicit_uniform_location GL_ARB_fragment_coord_conventions GL_ARB_fragment_layer_viewport GL_ARB_fragment_program GL_ARB_fragment_program_shadow GL_ARB_fragment_shader GL_ARB_fragment_shader_interlock GL_ARB_framebuffer_no_attachments GL_ARB_framebuffer_object GL_ARB_framebuffer_sRGB GL_ARB_geometry_shader4 GL_ARB_get_program_binary GL_ARB_get_texture_sub_image GL_ARB_gl_spirv GL_ARB_gpu_shader5 GL_ARB_gpu_shader_fp64 GL_ARB_gpu_shader_int64 GL_ARB_half_float_pixel GL_ARB_half_float_vertex GL_ARB_imaging GL_ARB_indirect_parameters GL_ARB_instanced_arrays GL_ARB_internalformat_query GL_ARB_internalformat_query2 GL_ARB_invalidate_subdata GL_ARB_map_buffer_alignment GL_ARB_map_buffer_range GL_ARB_multi_bind GL_ARB_multi_draw_indirect GL_ARB_multisample GL_ARB_multitexture GL_ARB_occlusion_query GL_ARB_occlusion_query2 GL_ARB_parallel_shader_compile GL_ARB_pipeline_statistics_query GL_ARB_pixel_buffer_object GL_ARB_point_parameters GL_ARB_point_sprite GL_ARB_post_depth_coverage GL_ARB_program_interface_query GL_ARB_provoking_vertex GL_ARB_query_buffer_object GL_ARB_robust_buffer_access_behavior GL_ARB_robustness GL_ARB_sample_locations GL_ARB_sample_shading GL_ARB_sampler_objects GL_ARB_seamless_cube_map GL_ARB_seamless_cubemap_per_texture GL_ARB_separate_shader_objects GL_ARB_shader_atomic_counter_ops GL_ARB_shader_atomic_counters GL_ARB_shader_ballot GL_ARB_shader_bit_encoding GL_ARB_shader_clock GL_ARB_shader_draw_parameters GL_ARB_shader_group_vote GL_ARB_shader_image_load_store GL_ARB_shader_image_size GL_ARB_shader_objects GL_ARB_shader_precision GL_ARB_shader_storage_buffer_object GL_ARB_shader_subroutine GL_ARB_shader_texture_image_samples GL_ARB_shader_texture_lod GL_ARB_shading_language_100 GL_ARB_shader_viewport_layer_array GL_ARB_shading_language_420pack GL_ARB_shading_language_include GL_ARB_shading_language_packing GL_ARB_shadow GL_ARB_sparse_buffer GL_ARB_sparse_texture GL_ARB_sparse_texture2 GL_ARB_sparse_texture_clamp GL_ARB_stencil_texturing GL_ARB_sync GL_ARB_tessellation_shader GL_ARB_texture_barrier GL_ARB_texture_border_clamp GL_ARB_texture_buffer_object GL_ARB_texture_buffer_object_rgb32 GL_ARB_texture_buffer_range GL_ARB_texture_compression GL_ARB_texture_compression_bptc GL_ARB_texture_compression_rgtc GL_ARB_texture_cube_map GL_ARB_texture_cube_map_array GL_ARB_texture_env_add GL_ARB_texture_env_combine GL_ARB_texture_env_crossbar GL_ARB_texture_env_dot3 GL_ARB_texture_filter_minmax GL_ARB_texture_float GL_ARB_texture_gather GL_ARB_texture_mirror_clamp_to_edge GL_ARB_texture_mirrored_repeat GL_ARB_texture_multisample GL_ARB_texture_non_power_of_two GL_ARB_texture_query_levels GL_ARB_texture_query_lod GL_ARB_texture_rectangle GL_ARB_texture_rg GL_ARB_texture_rgb10_a2ui GL_ARB_texture_stencil8 GL_ARB_texture_storage GL_ARB_texture_storage_multisample GL_ARB_texture_swizzle GL_ARB_texture_view GL_ARB_timer_query GL_ARB_transform_feedback2 GL_ARB_transform_feedback3 GL_ARB_transform_feedback_instanced GL_ARB_transform_feedback_overflow_query GL_ARB_transpose_matrix GL_ARB_uniform_buffer_object GL_ARB_vertex_array_bgra GL_ARB_vertex_array_object GL_ARB_vertex_attrib_64bit GL_ARB_vertex_attrib_binding GL_ARB_vertex_buffer_object GL_ARB_vertex_program GL_ARB_vertex_shader GL_ARB_vertex_type_10f_11f_11f_rev GL_ARB_vertex_type_2_10_10_10_rev GL_ARB_viewport_array GL_ARB_window_pos GL_ATI_draw_buffers GL_ATI_texture_float GL_ATI_texture_mirror_once GL_S3_s3tc GL_EXT_texture_env_add GL_EXT_abgr GL_EXT_bgra GL_EXT_bindable_uniform GL_EXT_blend_color GL_EXT_blend_equation_separate GL_EXT_blend_func_separate GL_EXT_blend_minmax GL_EXT_blend_subtract GL_EXT_compiled_vertex_array GL_EXT_Cg_shader GL_EXT_depth_bounds_test GL_EXT_direct_state_access GL_EXT_draw_buffers2 GL_EXT_draw_instanced GL_EXT_draw_range_elements GL_EXT_fog_coord GL_EXT_framebuffer_blit GL_EXT_framebuffer_multisample GL_EXTX_framebuffer_mixed_formats GL_EXT_framebuffer_multisample_blit_scaled GL_EXT_framebuffer_object GL_EXT_framebuffer_sRGB GL_EXT_geometry_shader4 GL_EXT_gpu_program_parameters GL_EXT_gpu_shader4 GL_EXT_multi_draw_arrays GL_EXT_packed_depth_stencil GL_EXT_packed_float GL_EXT_packed_pixels GL_EXT_pixel_buffer_object GL_EXT_point_parameters GL_EXT_polygon_offset_clamp GL_EXT_post_depth_coverage GL_EXT_provoking_vertex GL_EXT_raster_multisample GL_EXT_rescale_normal GL_EXT_secondary_color GL_EXT_separate_shader_objects GL_EXT_separate_specular_color GL_EXT_shader_image_load_formatted GL_EXT_shader_image_load_store GL_EXT_shader_integer_mix GL_EXT_shadow_funcs GL_EXT_sparse_texture2 GL_EXT_stencil_two_side GL_EXT_stencil_wrap GL_EXT_texture3D GL_EXT_texture_array GL_EXT_texture_buffer_object GL_EXT_texture_compression_dxt1 GL_EXT_texture_compression_latc GL_EXT_texture_compression_rgtc GL_EXT_texture_compression_s3tc GL_EXT_texture_cube_map GL_EXT_texture_edge_clamp GL_EXT_texture_env_combine GL_EXT_texture_env_dot3 GL_EXT_texture_filter_anisotropic GL_EXT_texture_filter_minmax GL_EXT_texture_integer GL_EXT_texture_lod GL_EXT_texture_lod_bias GL_EXT_texture_mirror_clamp GL_EXT_texture_object GL_EXT_texture_shared_exponent GL_EXT_texture_sRGB GL_EXT_texture_sRGB_decode GL_EXT_texture_storage GL_EXT_texture_swizzle GL_EXT_timer_query GL_EXT_transform_feedback2 GL_EXT_vertex_array GL_EXT_vertex_array_bgra GL_EXT_vertex_attrib_64bit GL_EXT_window_rectangles GL_EXT_import_sync_object GL_IBM_rasterpos_clip GL_IBM_texture_mirrored_repeat GL_KHR_context_flush_control GL_KHR_debug GL_KHR_no_error GL_KHR_robust_buffer_access_behavior GL_KHR_robustness GL_KTX_buffer_region GL_NV_alpha_to_coverage_dither_control GL_NV_bindless_multi_draw_indirect GL_NV_bindless_multi_draw_indirect_count GL_NV_bindless_texture GL_NV_blend_equation_advanced GL_NV_blend_equation_advanced_coherent GL_NV_blend_square GL_NV_command_list GL_NV_compute_program5 GL_NV_conditional_render GL_NV_conservative_raster GL_NV_conservative_raster_dilate GL_NV_copy_depth_to_color GL_NV_copy_image GL_NV_depth_buffer_float GL_NV_depth_clamp GL_NV_draw_texture GL_NV_draw_vulkan_image GL_NV_ES1_1_compatibility GL_NV_ES3_1_compatibility GL_NV_explicit_multisample GL_NV_fence GL_NV_fill_rectangle GL_NV_float_buffer GL_NV_fog_distance GL_NV_fragment_coverage_to_color GL_NV_fragment_program GL_NV_fragment_program_option GL_NV_fragment_program2 GL_NV_fragment_shader_interlock GL_NV_framebuffer_mixed_samples GL_NV_framebuffer_multisample_coverage GL_NV_geometry_shader4 GL_NV_geometry_shader_passthrough GL_NV_gpu_program4 GL_NV_internalformat_sample_query GL_NV_gpu_program4_1 GL_NV_gpu_program5 GL_NV_gpu_program5_mem_extended GL_NV_gpu_program_fp64 GL_NV_gpu_shader5 GL_NV_half_float GL_NV_light_max_exponent GL_NV_multisample_coverage GL_NV_multisample_filter_hint GL_NV_occlusion_query GL_NV_packed_depth_stencil GL_NV_parameter_buffer_object GL_NV_parameter_buffer_object2 GL_NV_path_rendering GL_NV_path_rendering_shared_edge GL_NV_pixel_data_range GL_NV_point_sprite GL_NV_primitive_restart GL_NV_register_combiners GL_NV_register_combiners2 GL_NV_sample_locations GL_NV_sample_mask_override_coverage GL_NV_shader_atomic_counters GL_NV_shader_atomic_float GL_NV_shader_atomic_fp16_vector GL_NV_shader_atomic_int64 GL_NV_shader_buffer_load GL_NV_shader_storage_buffer_object GL_NV_texgen_reflection GL_NV_texture_barrier GL_NV_texture_compression_vtc GL_NV_texture_env_combine4 GL_NV_texture_multisample GL_NV_texture_rectangle GL_NV_texture_shader GL_NV_texture_shader2 GL_NV_texture_shader3 GL_NV_transform_feedback GL_NV_transform_feedback2 GL_NV_uniform_buffer_unified_memory GL_NV_vertex_array_range GL_NV_vertex_array_range2 GL_NV_vertex_attrib_integer_64bit GL_NV_vertex_buffer_unified_memory GL_NV_vertex_program GL_NV_vertex_program1_1 GL_NV_vertex_program2 GL_NV_vertex_program2_option GL_NV_vertex_program3 GL_NV_viewport_array2 GL_NV_viewport_swizzle GL_NVX_conditional_render GL_NVX_gpu_memory_info GL_NVX_multigpu_info GL_NVX_nvenc_interop GL_NV_shader_thread_group GL_NV_shader_thread_shuffle GL_KHR_blend_equation_advanced GL_KHR_blend_equation_advanced_coherent GL_SGIS_generate_mipmap GL_SGIS_texture_lod GL_SGIX_depth_texture GL_SGIX_shadow GL_SUN_slice_accum GL_WIN_swap_hint WGL_EXT_swap_control
22:08:04.466 : OpenGL renderer:GeForce GTX 960/PCIe/SSE2
22:08:04.466 : Using fast VBOs for rendering is possible
22:08:22.683 : No start signal detected - forcing start
22:08:22.761 : FIRMWARE_NAME:Repetier_0.92 FIRMWARE_URL:https://github.com/luc-github/Repetier-Firmware-0.92 PROTOCOL_VERSION:1.0 MACHINE_TYPE:DaVinci EXTRUDER_COUNT:2 REPETIER_PROTOCOL:3
22:08:22.777 : Printed filament:0.00m Printing time:0 days 0 hours 0 min
22:08:22.823 : X:0.00 Y:0.00 Z:0.000 E:0.0000
22:08:22.823 : Begin file list
22:08:22.823 : eeprom.bin 4096
22:08:22.839 : End file list
22:08:27.676 : Info:Configuration reset to defaults.
22:08:31.238 : Info:Configuration stored to EEPROM.
22:08:38.302 : Starting object analyser ...
22:08:38.317 : Object is manifold.
22:08:38.317 : Analysing finished.
22:08:44.126 : Slic3r command:C:\Program Files\Repetier-Host\Slic3r\slic3r.exe --load "slic3r_settings.ini" --print-center 100.00,100.00 -o "composition.gcode" "composition.amf"
22:08:46.179 :
Thats all its showing now because i still have decoupling disabled, shall I reinable it?
luc-github
commented
8 years ago not this is not your GCODE - this is what repetier display you must export the GCODE file instead of send to printer
luc-github
commented
8 years ago Seiler270
commented
8 years ago ok let me try that.
also just loaded the .92 master with decoupling enabled again.
Seiler270
commented
8 years ago is this what you meant?
generated by Slic3r 1.2.9 on 2016-09-20 at 22:18:31
; external perimeters extrusion width = 0.40mm ; perimeters extrusion width = 0.48mm ; infill extrusion width = 0.48mm ; solid infill extrusion width = 0.48mm ; top infill extrusion width = 0.48mm
M107 M190 S70 ; set bed temperature M104 S211 ; set temperature G28 ; home all axes G1 Z5 F5000 ; lift nozzle
M109 S211 ; wait for temperature to be reached G21 ; set units to millimeters G90 ; use absolute coordinates M82 ; use absolute distances for extrusion G92 E0 G1 Z0.350 F7800.000
luc-github
commented
8 years ago Yes - ok I do not see anything wrong
using repetier to heat extruder does not work neither, right ?
again what about lcd screen ? no backlight + no char or backlight + no char ?
are the 3 red led working on your board ?
Seiler270
commented
8 years ago nothing on the screen at all, no backlight nothing.
using repetier the extruders will not heat, but the bed will
there are 2 red led on board that are on.
Im trying to flash via the directions here:
https://github.com/luc-github/Repetier-Firmware-0.92
Im a bit confused by step 4:
""""Update variants.cpp arduino file with the one present in src\ArduinoDUE\AdditionalArduinoFile according your IDE version""""
Ok so i can find the variant.cpp file in the repetier folder Lacated
C:xxxxxxxxxxxxx\Repetier-Firmware-0.92-master\src\ArduinoDUE\AdditionalArduinoFiles\Arduino - 1.6.9 -Due 1.6.8\Arduino15\packages\arduino\hardware\sam\1.6.8\variants\arduino_due_x
The issue is, where to I place it in the Ardino program group?
C:\Program Files (x86)\Arduino\hardware\arduino\avr\variants does not contain a variant.cpp files..
so where does it go?
I tried skipping the step, and continuing on and everything goes along as it should but after the firmware upload and the reboot i get nothing, its not even recognized by windows after that. I have to jumper J37 and start over.
Thanks for any help!