This program uses the fast flow-based method developed by Michael T. Gastner, Vivien Seguy, and Pratyush More. For more information, you may refer to the following paper:
Gastner MT, Seguy V, More P. Fast flow-based algorithm for creating density-equalizing map projections. Proc Natl Acad Sci USA 115(10):E2156–E2164 (2018). https://doi.org/10.1073/pnas.0400280101
Data produced by code in this repository are subject to the MIT license found here and should cite the aforementioned paper by Gastner et al. (2018).
Install homebrew by running the following command:
/bin/bash -c "$(curl -fsSL https://raw.githubusercontent.com/Homebrew/install/HEAD/install.sh)"
Install llvm, pkg-config, boost, fftw, cgal, nlohmann-json, and cmake by running the following command:
brew install llvm@17 libomp pkg-config boost fftw cgal nlohmann-json cmake cairo matplotplusplus
Run the following commands to install it:
sudo apt install build-essential manpages-dev software-properties-common
sudo add-apt-repository ppa:ubuntu-toolchain-r/test
sudo apt update && sudo apt install gcc-13 g++-13
Install nlohmann-json, cgal, openmp, fftw3, cairo, matplot++, boost, and cmake by running the following command:
sudo apt install nlohmann-json3-dev libcgal-dev libomp-dev libfftw3-dev libcairo2-dev libmatplot++-dev libboost-all-dev cmake
Go to the cartogram-cpp
directory in your preferred terminal and execute the following commands.
cmake -B build
make -C build
sudo make install -C build
If your computer has multiple cores, you may use the make
command with the -j
flag to use all your cores, or -j
followed by a number to use the specified number of cores (for example, -j4
to use 4 cores). You may perform the entire installation at once with:
sudo cmake -B build && sudo make install -j -C build
Using lesser cores than you have is recommended so that your computer still has some headroom for other tasks. Thus, it may be a good idea for you to modify the above snippet, appending your preferred number of cores to -j
.
build
directory with rm -rf build
and run the installation commands again.cmake -B build
gives you an error, it is likely that a dependency was not installed correctly. Rerun the appropriate commands above to install the required dependencies and try again.sudo
prefixed, as done with sudo make install -C build
above.cmake
complains that it could not find a particular library, please try uninstalling it and installing it again. After reinstalling it, please also unlink it and link it with the --force
flag.Run the following command (replace your-geojson-file.geojson
file with your geographic data and your-csv-file.csv
with your visual variables file, containing target areas for each geographic region):
cartogram your-geojson-file.geojson your-csv-file.csv
.csv
file with data about target areas.Note: use the -h
flag to display more options.
The CSV file should be in the following format:
NAME_1 | Data (e.g., Population) | Color |
---|---|---|
Bruxelles | 1208542 | #e74c3c |
Vlaanderen | 6589069 | #f1c40f |
Wallonie | 3633795 | #34495e |
NAME_1
should be the same as the identifying property's name in the GeoJSON. The rows should also have the same data as is present in the identifying property.Data
contains the data you would like your cartogram to based on.Color
is the color you would like the geographic region to be. Colors may be represented in the following manner:
cornflowerblue
: html color codes supported by CSS3
(case-insensitive), full list of supported colors may be found in the "Extended colors" section of web colors."rgb(255, 0, 120)"
or rgb(255 0 120)
or "255, 0, 120"
or 255 0 120
: red, green and blue values out of 255.#e74c3c
: hex code of color, must start with #
.You may find sample GeoJSON (containing geographic data) and CSV (containing information about target areas, colors and other visual variables) files in the cartogram-cpp/sample_data
directory.
If you'd like to contribute to the project, please run our tests after you make any changes.
To run the unit tests, execute the following command:
ctest --verbose
To learn more about the tests, you may go to the cartogram-cpp/tests
directory and read the README.md
file.
Additionally, you may go to the cartogram-cpp/tests
directory and run the following command:
bash stress_test.sh
Go to the cartogram-cpp
directory in your preferred terminal and execute the following command:
sudo make uninstall -C build
Upon successful uninstallation, the following will be outputted:
> Built target uninstall
Further, running cartogram
should no longer work.