Prepare to build the driver, you need the Linux kernel sources installed on the build machine, and make sure that the version of the running kernel must match the installed kernel sources. If you don't have the kernel sources, you can get it from www.kernel.org or contact to your Linux distributor. If you don't know how to do, please refer to KERNEL-HOWTO.
Note: Please make sure the kernel is built with one of the "Support for Host-side, XHCI, EHCI, OHCI, or UHCI" option support.
Extract the compressed driver source file to your temporary directory by the following command: $tar -xf DRIVER_SOURCE_PACKAGE.tar.bz2
Now, the driver source files should be extracted under the current directory. Issue the following command to compile the driver: $make
If the compilation is done, the ax_usb_nic.ko will be created under the current directory.
=== Install driver to your system
If you want to use modprobe command to mount the driver, issue the following command to install the driver into your system: $sudo make install Note: This command will backup the built-in ax88179_178a driver if it exists.
If you want to load the driver by modprobe command, issue the following commands: $sudo modprobe ax_usb_nic
If you want to unload the driver by modprobe command, issue the following commands: $sudo modprobe -r ax_usb_nic
If you want to check the information of driver, issue the following commands: $modinfo ax_usb_nic
=== Install driver manually
If you want to load the driver manually, go to the driver directory and execute the following commands: $sudo modprobe mii $sudo insmod ax_usb_nic.ko
If you want to unload the driver, just executing the following command: $sudo rmmod ax_usb_nic
If you want to check the information of driver, issue the following commands: $modinfo ax_usb_nic.ko
ASIX USB Ethernet Linux Command Line Programming Tool
[Note]: Enable DEBUG message
Extract the compressed driver source file to your temporary directory by the following command: $tar -xf DRIVER_SOURCE_PACKAGE.tar.bz2
Now, the driver source files should be extracted under the current directory. Executing the following command to compile the driver: $make
Load the driver manually, go to the driver directory and execute the following commands: $sudo modprobe mii $sudo insmod ax_usb_nic.ko
If the compilation is well, the ioctl will be created under the current directory.
Note: The default way to find the interface is to scan the ASIX device using the ethx (x: 0~255).It is defined in the file, command.h. (As follows) ... // DEFAULT_SCAN : scan "eth0" - "eth255" // INTERFACE_SCAN : scan all available network interfaces
#define DEFAULT_SCAN 0x00
#define INTERFACE_SCAN 0x01
...
Adjust the contents of #define NET_INTERFACE to select the method you want.
If you want to enable the PTP function, please modify ENABLE_PTP_FUNC to 'y' in the makefile, and then recompile it.
ENABLE_PTP_FUNC = n -> ENABLE_PTP_FUNC = y
=== AX88179/178A EEPROM/eFuse Programmer
If you want to read out values of the EEPROM/EFUSE to a file, go to the driver directory and execute the following command: $sudo ./ax88179_programmer reeprom 0 eeprom 512 $sudo ./ax88179_programmer reeprom 1 efuse 64
If you want to write values of a file to the EEPROM/EFUSE, go to the driver directory and execute the following command: $sudo ./ax88179_programmer weeprom 0 eeprom 512 $sudo ./ax88179_programmer weeprom 1 efuse 64
If you want to change the MAC address of a dongle, go to the driver directory and execute the following command: $sudo ./ax88179_programmer chgmac 0 mac_addr 512 $sudo ./ax88179_programmer chgmac 1 mac_addr 64
If you need more information about the instructions, go to the driver directory and execute the following commands: $sudo ./ax88179_programmer reeprom help $sudo ./ax88179_programmer weeprom help $sudo ./ax88179_programmer chgmac help
=== AX88179B/179A/772E/772D Flash/eFuse Programmer
If you want to get help message for specific command, go to the driver directory and execute the following command: $sudo ./ax88179b_179a_772e_772d_programmer help [command]
If you want to get the version of firmware, go to the driver directory and execute the following command: $sudo ./ax88179b_179a_772e_772d_programmer rversion
If you want to get the MAC address, go to the driver directory and execute the following command: $sudo ./ax88179b_179a_772e_772d_programmer rmacaddr
If you want to write values of a file to the flash, go to the driver directory and execute the following command: $sudo ./ax88179b_179a_772e_772d_programmer wflash [file]
If you want to write the eFuse, go to the driver directory and execute the following command: $sudo ./ax88179b_179a_772e_772d_programmer wefuse -m [MAC] -s [SN] -f [File] --led0 [value] --led1 [value] -p [device] -m [MAC] - MAC address (XX:XX:XX:XX:XX:XX) -s [SN] - Serial number -f [File] - eFuse file path --led0 [value] - value: control_blink (XXXX_XXXX) --led1 [value] - value: control_blink (XXXX_XXXX) -p [device] - device: "AX88179B" or "AX88179A" or "AX88772E" or "AX88772D" example: $sudo ./ax88179b_179a_772e_772d_programmer wefuse -m 00:0E:C6:81:79:01 -s 00000000000001 -f eFuse_Dump.txt
$sudo ./ax88179b_179a_772e_772d_programmer wefuse -m 00:0E:C6:81:79:01
-s 0000000000179A --led0 8007_0000 --led1 8000_003F -p AX88179A
$sudo ./ax88179b_179a_772e_772d_programmer wefuse -m 00:0E:C6:87:72:D1
-s 0000000000772D -p AX88772D
If you want to read the eFuse, go to the driver directory and execute the following command: $sudo ./ax88179b_179a_772e_772d_programmer refuse -f [File]
If you want to reload the flash or eFuse to check version or MAC address and so, go to the driver directory and execute the following command: $sudo ./ax88179b_179a_772e_772d_programmer reload
=== AX88179B/179A/772E/772D IEEE Test Tool
If you want to execute IEEE test, go to the driver directory and execute the following command:
$sudo ./ax88179b_179a_772e_772d_ieee ieeetest speed option -- AX88179B_179A_772E_772D IEEE Test Tool [speed] - 1000: 1000Mbps, 100: 100Mbps, 10: 10Mbps [option] - For 1000Mbps M1: Mode 1 M2: Mode 2 M3: Mode 3 M4: Mode 4
- For 100Mbps
CA: Channel A
CB: Channel B
- For 10Mbps
RP: Random Pattern
FF: Fixed Pattern(FF)
MDI: MDI
=== AX88279 Linux Flash Programming Tool
If you want to get help message for specific command, go to the driver directory and execute the following command: $sudo ./ax88279_programmer help [command]
If you want to get the version of firmware, go to the driver directory and execute the following command: $sudo ./ax88279_programmer rversion
If you want to get the MAC address, go to the driver directory and execute the following command: $sudo ./ax88279_programmer rmacaddr
If you want to write values of a file to the flash, go to the driver directory and execute the following command: $sudo ./ax88279_programmer wflash [file]
If you want to write the parameter in flash, go to the driver directory and execute the following command: $sudo ./ax88279_programmer wpara -m [MAC] -s [SN] -p [PID] -v [VID] -P [PS] -M [MN] -D [dump] -S [SS] -H [HS] -w [wol] -l [led0 value] -e [led1 value] -d [led2 value] -m [MAC] - MAC address (XX:XX:XX:XX:XX:XX) X:'0'-'F' -s [SN] - Serial Number (Characters must be less than 19 bytes) X:'0'-'F' -p [PID] - Product ID (XX:XX) X:'0'-'F' -v [VID] - Vendor ID (XX:XX) X:'0'-'F' -P [PS] - Product String (Characters must be less than 19 bytes) -M [MN] - Manufacture Name (Characters must be less than 19 bytes) -D [dump] - The parameter content currently in flash (dump) -S [SS] - SS bus power (XX) X:0-896 mA -H [HS] - HS bus power (XX) X:0-500 mA -w [wol] - wake on LAN (XXXXXXXX) X:1 or 0 (About setting dwol_enable s5wol_enable pme_enable) -l [led0 value] - value: control_blink (XXXX_XXXX) -e [led1 value] - value: control_blink (XXXX_XXXX) example: $sudo ./ax88279_programmer wpara -m 00:0e:c6:81:79:01 -s 00000000000001
$sudo ./ax88279_programmer wpara -p 17:90 -v 0b:95 -P ax88279 -M asix
$sudo ./ax88279_programmer wpara -S 400 -H 200 -w 01000001(represent:bit[1]= 1, bit[7]= 1)
$sudo ./ax88279_programmer wpara -l C113_0004 -e C002_0C4F
explain: -w bit[0] -> Disable Remote Wakeup, bit[1] -> PME enable, bit[2] -> DWOL Magic Packet, bit[3] -> DWOL Link Change, bit[4] -> S5 WOL Magic Packet, bit[5] -> S5 WOL Link Change, bit[6] -> PME Retry Enable, bit[7] -> PME IND Enable,
If you want to view the current parameter content in flash, go to the driver directory and execute the following command, and you can see the file parameter.txt in driver directory: $sudo ./ax88279_programmer wpara -D dump
If you want to reload the flash to check version or MAC address and so, go to the driver directory and execute the following command: $sudo ./ax88279_programmer reload