nerves-networking / vintage_net_wizard

WiFi configuration wizard using vintage_net
Apache License 2.0
60 stars 21 forks source link

VintageNet WiFi Configuration Wizard

CircleCI Coverage Status Hex version

This is a WiFi configuration wizard that uses VintageNet. It is intended for use in Nerves-based devices that don't have a display for configuring WiFi.

Here's the intended use:

  1. On device initialization, if WiFi hasn't been configured, configure WiFi to AP mode and start a webserver
  2. A user connects to the access point and opens a web browser. The only website they can go to in the configuration utility.
  3. The configuration utility shows a list of access points and the user can select one or more or enter information for a hidden access point
  4. The user applies the configuration and the device stops AP mode and connects to the access point.

VintageNet persists WiFi configuration so the device will be able to connect after reboots and power outages. To change the configuration later, a user needs to take a device-specific action like hold down a button for 5 seconds. This library has an example project for the Raspberry Pi for use as a demo.

see it in action

Features

Supported WiFi adapters

Not all WiFi adapters support AP mode. Here are the ones that we've used:

  1. Raspberry Pis with built-in WiFi modules (like the RPi 3, 4 and Zero W)
  2. RT5370-based USB modules
  3. Edimax EW-7612UAn V2 (See note)

It is highly likely that other modules work. We have not had any luck with other Realtek RTL8192c (in the popular Edimax EW7811Un) or MediaTek MT7601u (in lots of brands).

NOTE: For the Edimax EW-7612UAn V2 to work, you'll need to create a custom Nerves system with CONFIG_RTL8192CU=m in the linux-x.xx.defconfig as well as BR2_PACKAGE_LINUX_FIRMWARE=y and BR2_PACKAGE_LINUX_FIRMWARE_RTL_81XX=y in nerves_defconfig.

Configuration

It is expected that you're using VintageNet already. If you're not, see that project first.

VintageNetWizard is an OTP application so it's mostly self-contained. Add it to your mix dependencies like so:

   {:vintage_net_wizard, "~> 0.4"}

The configuration wizard is not started by default to allow for more control over business specific situations. You will need to add a call in your code when you want the device placed into AP mode and the wizard started:

defmodule MyApp do
  use Application

  def start(_type, _args) do
    if should_start_wizard?() do
      VintageNetWizard.run_wizard
    end
    # ...
    Supervisor.start_link(children, opts)
  end
end

This will be sufficient to try it out on a device that hasn't been configured yet. You will want to add a mechanism for forcing the wizard the run WiFi configuration again, such as holding a button for 5+ seconds. Take a look at Running the example section for steps on setting up a button and running a quick example firmware on a device.

UI Customization

VintageNetWizard allows you to add customization to the UI. The three UI items that can be customized are: :title, :title_color, and :button_color.

VintageNetWizard.run_wizard(
  ui: [title: "My WiFi Wizard", title_color: "red", button_color: "#F0F0AD"]
)

Each configuration option is optional and will fall back to VintageNetWizards default colors and title.

DNS in AP-mode

When the wizard is running, users go to either http://192.168.0.1/ or http://wifi.config/ to access the web user interface. Both can be changed via the config.exs:

config :vintage_net_wizard,
  dns_name: "my-wifi-config.com",
  subnet: "192.168.0.0"

Port

VintageNetWizard starts a webserver on port 80 by default. If port 80 is not available on your device or you would prefer a different port, add the following to your config.exs:

config :vintage_net_wizard,
  port: 4001

If SSL is enabled the default port is 443.

SSL

To use SSL with the web UI, you can pass SSL options to VintageNetWizard.run_wizard/1:

VintageNetWizard.run_wizard(ssl: [keyfile: "/path/to/key.pem", certfile: "/path/to/cert.pem"])

To see all available options see Plug.SSL.configure/1 and Erlang's :ssl module.

Device Info

If you want to display extra data about the device in the footer of the UI you can pass in a list of key-value pairs to VintageNetWizard.run_wizard/1:

VintageNetWizard.run_wizard(device_info: [{"Serial number", "1234"}, {"Version", "0.1.0"}])

The first item in the key-value pair is display name of the info and the second item will be the value of the item.

Interface name

VintageNetWizard uses "wlan0" by default. If you have more than one wireless LAN or the interface is called something else, pass the appropriate interface name to VintageNetWizard.run_wizard/1 to use it:

VintageNetWizard.run_wizard(ifname: "wlan1")

Backends

Backends control how VintageNetWizard configures the network. The default backend changes the network configuration as you would expect. This can get in the way of development and can be disabled by using the VintageNetWizard.Backend.Mock backend:

config :vintage_net_wizard,
  backend: VintageNetWizard.Backend.Mock

Captive Portal

Captive portal is enabled by default. If using a port other than 80 then all traffic on port 80 will be captured and redirected to the specified wizard address in order to trigger the portal.

You can disable captive portal in your configuration:

config :vintage_net_wizard, captive_portal: false

Inactivity Timeout

After a set mount of time of inactivity the wizard will timeout and shut down the server. This prevents a device using the wizard to infinitely be in AP mode. The default timeout is 10 minutes, but can be configured:

config :vintage_net_wizard,
  inactivity_timeout: <timeout in minutes>

The timeout can also be explicitly disabled by supplying :infinity:

config :vintage_net_wizard,
  inactivity_timeout: :infinity

JSON API

It is possible to write a smartphone app to configure your device using an API endpoint. Documentation for the API is in json-api.md.

Running the example

The example builds a Nerves firmware image for supported Nerves devices that demonstrates the wizard. The wizard will run on the first boot and also after a button has been held down for 5 seconds.

For the button to work, you'll need to wire up a button to GPIO 17/pin 11 and 3v3/pin 1 on the Raspberry Pi's GPIO header. See the image below for the location:

Raspberry Pi Pinout from pinout.xyz

If you don't have a button, you can use a jumper wire to temporarily connect 3v3 power to pin 11. If you have a Raspberry Pi hat with a button connected to a different GPIO pin, you can specify with pin to use in your config:

config :wizard_example, gpio_pin: 27

The next step is to build the firmware. Make sure that you've installed Nerves and run the following:

cd example

# Set the target to rpi0, rpi3, or rpi4 depending on what you have
export MIX_TARGET=rpi3
mix deps.get
mix firmware

# Insert a MicroSD card or whatever media your board takes
mix burn

Place the MicroSD card in the Raspberry Pi and power it on. You should see a WiFi access point appear with the SSID "nerves-1234" where "1234" are part of the device's serial number. Connect to the access point and then point your web browser at http://wifi.config or http://192.168.0.1/. If you've configured an SSL certificate, it's possible to use https. You may also need to change the :dns_name configuration to match the name on your SSL certificate.

The SSID defaults to the hostname of the device, and you can change the SSID via the config.exs:

config :vintage_net_wizard,
  ssid: "MY_SSID"

Stop callback

If your application runs a webserver or has other functionality that is incompatible with the wizard, you can use the :on_exit option to VintageNetWizard.run_wizard/1 to register a completion callback. The callback has the form, {module, function, args}. Here's an example:

defmodule MyApp do
  def start_wizard() do
    VintageNetWizard.run_wizard(
      on_exit: {__MODULE__, :handle_on_exit, []}
    )
  end

  def handle_on_exit() do
    Logger.info("VintageNetWizard stopped")
  end
end

Development

It's possible to work on the wizard locally and without using Nerves or changing the network settings of your development machine:

$ mix deps.get
$ iex -S mix

iex> VintageNetWizard.run_wizard

07:49:00.710 [info]  Go to http://localhost:4001/
:ok

Look in lib/vintage_net_wizard/backend/mock.ex if you need to change anything for your testing.