ESP32 modbus module intended for use with Home Assistant to support various modbus enabled devices. Currently I have used and tested:
There are a couple of additional code examples that has been tested and verified by users om the example code folder.
The module is not limited to those applications, but since I haven't tried other applications I give no promises !
You can buy the module here: https://www.ustepper.com/shop/#!/products/esphome-modbus-module
Do this at your own risk ! You are interfacing with hardware that you can potentially damage if you do not connect things as required ! Using the hardware and code presented here is done at you own risk. The hardware and software has been tested on the devices listed above without issues.
On Wavin you simply use a patch cable (straight) and connect it from the module to the Modbus port and then you are done :)
So, taking an RJ45B cable and cutting it will leave you with colored wires that have the functions as shown below (for a RJ45B !):
Generally you need A (modbus+), B (modbus-), GND and optionally you can connect 8-24VDC to the +12V wires or you can plug in the USB-C cable from e.g., a charger to power the module. The module can consumer up to 340mA on 3.3V which for a 12V supply would be 100mA and 50mA for 24V as the module has a power converter without too much loss.
The module is intended for use with Home Assistant and ESPHome though not limited to this.
See the video guide for uploading AHC9000 software to the module from your laptop using USB: https://youtu.be/Q5KRcv-uObo
For Wavin, you need to add/delete the channels and edit names to match your setup. The procedure for programming is the same for all code bases - Nilan, Nibe, EM340 etc...
See the video guide here on how to set it up wirelessly (Wavin Sentio example): https://youtu.be/s8QjRjI9TLo
Besides my example codes for CTS602, 602 light and CTS400 you can find generic code for all Nilan here: https://github.com/Jopand/esphome_components/blob/main/README.md
The only board specific thing to include is:
esphome:
name: nilan
esp32:
board: esp32-c3-devkitm-1
framework:
type: arduino
wifi:
ssid: !secret wifi_ssid
password: !secret wifi_password
output_power: "8.5"
uart:
rx_pin: 20
tx_pin: 21
parity: EVEN
baud_rate: 19200
id: uart_modbus
stop_bits: 1
modbus:
id: modbus_id
flow_control_pin: 10
uart_id: uart_modbus
Where baud rate must match your system of course - here a Nilan example.
The module includes:
The form factor and visuals is the same as for the previous ESP32-PICO. The change results in a BOM reduction and thus a price reduction due to the integrated USB controller in the C3.
The following schematic shows the details of the module:
The board dependent setup part is as follows for the ESP32-C3:
esphome:
name: nilan
esp32:
board: esp32-c3-devkitm-1
framework:
type: arduino
wifi:
ssid: !secret wifi_ssid
password: !secret wifi_password
output_power: "8.5"
uart:
rx_pin: 20
tx_pin: 21
parity: EVEN
baud_rate: 19200
id: uart_modbus
stop_bits: 1
modbus:
id: modbus_id
flow_control_pin: 10
uart_id: uart_modbus
The module includes:
Rendering of the module can be seen here:
The following schematic shows the details of the module:
The board dependent setup part is as follows:
esphome:
name: nilan
esp32:
board: pico32
framework:
type: arduino
uart:
rx_pin: 13
tx_pin: 14
parity: EVEN
baud_rate: 19200
id: uart_modbus
stop_bits: 1
modbus:
id: modbus_id
flow_control_pin: 26
uart_id: uart_modbus