Introduction

BouffaloSDK is an MCU software development kit provided by the Bouffalo Lab Team, supports all the series of Bouffalo chips.

SDK Architecture

Code Directories

Name	Description
bsp/board	clock, pinmux, memoryheap and console init
bsp/common	bsp common driver
components	components
docs	quick start、 api、demo doc
drivers/lhal	bouffalo common peripherals drivers which support all the chips
drivers/soc	bouffalo non-generic peripherals drivers
drivers/rfparam	rf param
examples	official samples
tools	tools

LHAL Support

LHAL is a low level hal driver for common peripherals designed by Bouffalo Lab, in order to support all the Bouffalo chips with the same api . Also it is convenient for users to use and port to other platforms.

Note：√ means supported ; × means not supported; ○ means supported but not tested ; - means no such peripheral.

Peripheral	BL602/BL604	BL702/BL704/BL706	BL616/BL618	BL808
ADC	○	√	√	○
CAM	-	×	×	×
CKS	○	√	√	○
DAC	○	√	√	○
DMA	○	√	√	√
EFUSE	×	×	×	×
EMAC	-	√	√	√
FLASH	√	√	√	√
GPIO	○	√	√	√
I2C	○	√	√	○
I2S	○	○	√	○
IR	○	√	√	○
MJPEG	×	×	√	√
PWM_v1	○	√	-	-
PWM_v2	-	-	√	√
RTC	○	√	√	√
SEC_AES	○	√	√	√
SEC_SHA	○	√	√	√
SEC_TRNG	○	√	√	√
SEC_PKA	○	√	√	√
SPI	○	√	√	√
TIMER	○	√	√	√
UART	√	√	√	√
USB_v1	-	√	-	-
USB_v2	-	-	√	√
WDG	○	√	√	○

Environment Setup

Toolchain

riscv64-unknown-elf-gcc toolchain used in windows.
riscv64-unknown-elf-gcc toolchain used in linux.
linux-riscv64-linux-gcc toolchain used for compiling linux code.

Command Line Development

Before compiling with the command line, you need to select the corresponding toolchain according to your operating system, configure it to the system environment variables, and install the make or ninja, then you can do the following. For the details, you can visit BouffaloSDK Environment Setup.

Go to the demo directory where you want to compile and there are main.c and Makefile files in that directory
Just execute the following command, take BL616 as an example

cd examples/helloworld
make CHIP=bl616 BOARD=bl616dk

If you use BL808 or BL606P, you need to add CPU_ID with m0 or d0.

If you want to use ninja, you can try:

cd examples/helloworld
make ninja CHIP=bl616 BOARD=bl616dk

cd examples/helloworld
make CHIP=bl808 BOARD=bl808dk CPU_ID=m0

CDK Development

TODO

Debug

Only supports debug with CKLink currently. See BouffaloSDK Debug Guide.

Firmware Download

Note that if you are using linux, linux will deny access to the serial device due to permission issues, so add your own username to dialout for easy to use, restart your linux and then take effect. Or add sudo before command.

usermod -aG dialout xxx # xxx is your own name

cd examples/helloworld
make flash CHIP=chip_name COMX=xxx # chip_name should be bl602/bl702/bl616/bl808/bl606p, COMX in Windows, /dev/ttyxxx in Linux

If you use BL808 or BL606P, you need to add CPU_ID with m0 or d0.

cd examples/helloworld
make flash CHIP=chip_name CPU_ID=m0 COMX=xxx # chip_name should be bl602/bl702/bl616/bl808/bl606p, COMX in Windows, /dev/ttyxxx in Linux

If flash using serial port rather than USB, different USB2TTL chips support different max baudrates, need to pay attention to when flashing.

chip	baudrate
ch340	<= 500K
cp2102	<= 2M
ft232	<= 2M
bl702	<= 8M
bl616	<= 10M

Resources

Chip Manual

Chip Reference Manual and Chip Data Manual are listed on document

Documentation Tutorial

To get more BouffaloSDK documentation tutorial, like api manual or peripheral demo and so on, please visit:

BouffaloSDK documentation tutorial

Video Tutorial