An evohome to MQTT gateway
Note There has been a major rewrite of evoGateway (previously evoListener) as of May 2021, where the underlying underlying decoding (and encoding) of the evohome radio communications has been completely replaced using the excellent ramses_rf
framework library. This has improved the robustness of the system and brought it up to date with some of the previously missing commands now being fully decoded.
However, this has meant that there are a number of breaking changes within this version (currently version 3.0), for those coming from an earlier version. In many respects, it may be easier to start fresh with this version.
evoGateway is a 'gateway' python script that provides an MQTT interface for listening to and sending commands via the radio communcation network between Honeywell's evohome heating control devices. The hardware required for this script is is just (a) an arudino with a USB connector and (b) a CC1101 868Mhz radio receiver board (see below).
Any messages received by the radio is decoded and sent to an MQTT broker (copies are also saved to local log files). Additionally, the script subscribes to an MQTT topic for local user commands, which are appropriate encoded and sent out over the evohome radio network directly as if they orginated from a Honeywell evohome device.
In effect, with this script/hardware, one can have local control over evohome - e.g. with a home automation solution such as openHAB - without needing to go via Honeywell's cloud API.
The script requires python (preferabley version 3.8) and the following modules:
These can be installed by running pip install -r requirements.txt
).
Note that this script has only been tested on an Ubuntu 20.04 server running in a VM, with python 3.8.0.
Configuration parameters are defined in a separate file, evogateway.cfg
, with the format and parmaeters as given below. The only mandatory parameter is the COM_PORT
. All others are optional (obviously without the MQTT broker details, nothing will be posted to an MQTT broker!):
[Serial Port]
# Serial port is mandatory
COM_PORT = /dev/ttyUSB0
# Optional
COM_BAUD = 115200
[Files]
# The following are optional
EVENTS_FILE = gw_events.log
PACKET_LOG_FILE = gw_packets.log
DEVICES_FILE = devices.json
SCHEMA_FILE = ramses_rf_schema.json
MAX_SAVE_FILE_COUNT = 9
[MQTT]
MQTT_SERVER = x.x.x.x
MQTT_USER = userid
MQTT_PW = password
MQTT_PUB_TOPIC = evohome/evogateway
MQTT_SUB_TOPIC = evohome/evogateway/_zone_independent/command
MQTT_CLIENTID = evoGateway
#Publish as a single json string. If False, the key/values of the json will be published individually
MQTT_PUB_AS_JSON = False
# Either group published messages by zone name (default), otherwise by device name
MQTT_GROUP_BY_ZONE = True
[MISC]
# optional
THIS_GATEWAY_NAME = evoGateway
# Display full json string from evohome_rf, or just key data item for each row
DISPLAY_FULL_JSON = False
In contrast to earlier versions, the script is now almost fully automated in the way it discovers devices, and gets zone names directly from the controller etc (another of the benefits of the ramses_rf library!).
The first time the script is run, it will run in the ramses_rf 'eavesdrop' mode, whereby it will attempt to listen in on the radio communications between the evohome devices on the network, and build an internal schema of all the available devices, their types and parameters (e.g. zone names, valid temperature ranges etc). This should be left to run for a reasonable amount of time, to ensure that it has picked up communications from all the devices. Some devices, such as the DHW wireless sender, can in some instances take up to an hour before sending a message.
A list of currently found devices can be seen at any time by sending a POST_SCHEMA
command (see below) to the subscribed MQTT channel. This will post the current 'schema', including a list of the devices and zones names detected so far etc, to the evohome/evogateway/_zone_independent/_gateway_config
MQTT topic. On exiting the system, a copy of the internal schema is then saved to a file (default ramses_rf_schema
), and loaded back during subsequent runs of the script. This file should not normally need to be manually edited (previous versions are overwritten with the current version).
Additionally, a devices.json
file is also saved. This file is a simple json dictionary of the device IDs detected along with a default device name based on its zone name (if the zone name is available at the time the file is saved). This file can be edited manually. Incorrect devices (i.e. those misinterpreted during the 'eavesdrop' or those from neighbours etc) should be removed. Device names can also be changed here and will be used for the MQTT topic instead of the device id.
Note that the IDs in this devices.json
forms the allowed_list
- i.e. only messages from devices itemised in this file will be processed in future.
The devices (and schema) files can also be force saved at any time by sending the command SAVE_SCHEMA
.
Similarly, eavesdropping mode can be re-initiated by deleting the devices.json
and the ramses_rf_schema
files.
The gateway script subsribes to a specific MQTT topic (by default evohome/evogateway/_zone_independent/command
) for user commands to be sent out over the evohome radio network.
JSON messages to this topic are picked up by the script, processed and converted into the format required by evohome, and then transmitted to the appropriate device. For this process, the gateway script in-effect pretends to be an Honeywell HGI80 device, with a device ID starting with 18:
(the ID is fixed in the arduino firware).
For users coming from earlier versions, it should be noted that the content of the JSON message to send commands has signficantly changed, to keep aligned with the underlying ramses_rf library. The new format of the JSON send command message is as follows:
{"command": "<command method>", "<keyword 1>" : "<keyword 1 value>", "<keyword 2>" : "<keyword 2 value>"...}
Code 1F41, command method: get_dhw_mode(ctl_id)
Code 0404, command method: get_dhw_schedule_fragment(ctl_id, frag_idx, frag_cnt)
Code 3220, command method: get_opentherm_data(dev_id, msg_id)
Code 0418, command method: get_system_log_entry(ctl_id, log_idx)
Code 2E04, command method: get_system_mode(ctl_id)
Code 313F, command method: get_system_time(ctl_id)
Code 1100, command method: get_tpi_params(ctl_id)
Code 000A, command method: get_zone_config(ctl_id, zone_idx)
Code 2349, command method: get_zone_mode(ctl_id, zone_idx)
Code 0004, command method: get_zone_name(ctl_id, zone_idx)
Code 0404, command method: get_zone_schedule_fragment(ctl_id, zone_idx, frag_idx, frag_cnt)
Code 1F41, command method: set_dhw_mode(ctl_id, mode, active, until)
Code 10A0, command method: set_dhw_params(ctl_id, setpoint, overrun, differential)
Code 1030, command method: set_mix_valve_params(ctl_id, zone_idx, max_flow_setpoint, min_flow_setpoint, valve_run_time, pump_run_time)
Code 2E04, command method: set_system_mode(ctl_id, system_mode, until)
Code 313F, command method: set_system_time(ctl_id, datetime)
Code 1100, command method: set_tpi_params(ctl_id, domain_id, cycle_rate, min_on_time, min_off_time, proportional_band_width)
Code 000A, command method: set_zone_config(ctl_id, zone_idx, min_temp, max_temp, local_override, openwindow_function, multiroom_mode)
Code 2349, command method: set_zone_mode(ctl_id, zone_idx, mode, setpoint, until)
Code 0004, command method: set_zone_name(ctl_id, zone_idx, name)
Code 2309, command method: set_zone_setpoint(ctl_id, zone_idx, setpoint)
The controller ID keyword ctl_id
is optional and if not provided in the JSON message, will default to the internal one (i.e. from the eavesdropped schema).
An example JSON MQTT message for getting the first system log entry from the Controller would thus be:
{"command" : "get_system_log_entry", "log_idx": 0}
Date/time values should be sent in the in the usual iso format, e.g. to turn the hot water one until 17:40 on 31st May 2021:
{"command" : "set_dhw_mode", "active": true, "until" : "2021-05-31T17:40:00"}
In addition to using the built-in ramses_rf command constructors, a command code
can still be sent but again the message structure has been changed to keep aligned with the ramses_rf framework. When sending a command code
, both verb
and payload
must also be included, where verb
is usually RQ, RP, W etc. and payload
is the hex payload that for the given command code. Optionally dest_id
may be specified with the ID of the recipient device, if the command is not being sent to the controller (default).
An equivalent example for getting the 1st system log entry but using the command code would be:
{"code" : "0418", "verb": "RQ", "payload": "000000"}
Status updates for commands sent via the evohome network are posted to the topic evohome/evogateway/_zone_independent/command/_last_command/status
.
Finally, there are a few 'system' commands available for use whilst evoGateway is running. These are called by sending sys_config
values (instead of the previous command
and code
). Currently available commands are:
NOTE The hardware can be purchased fully assembled, including proper PCB, from ebay (search for nanoCUL FTDI 868MHz
), or in component form from ebay/Ali Express etc.
If assembling yourself, you will need:
1 x Arduino nano (clone should be fine), preferably with FTDI usb chipset, though the cheaper CH341 chipset also worked. The only issue I had with the CH341 was that the USB port was not always cleanly released when the python script exited. My FTDI based build is much more reliable in this respect.
1 x CC1101 radio, 868MHz, e.g. something like this. However, note that there has been some report of issues with the radio crystal's accuracy on some of these boards (discussion on evofw3 board).
A breadboard or 8 x Dupont fly leads. If using fly leads you need to ensure that sure that you have the correct male/female combination for your arduino and CC1101 card.
Wiring pin connections will depend on the specific CC1101 board. In my case, I used the following:
WIRE COLOUR CC1101 PIN NANO PIN
Red Vcc 3.3V pin
Black GND GND
Orange MOSI 15
Yellow SCLK 17
Blue MISO 16
Dark Red GDO2 32
Grey GDO0 1
White CSN 14
ANT Antenna coil
Although arduinos with the FTDI FT232L chipset are recommended, clone nanos with the CH341 usb chip have also worked reasonably. In my case the radio board is connected directly to the nano using just male/female dupont wires, with the male side soldered directly onto the radio board. Note that actual pin connection points should always follow the requirements of evofw3 (e.g. see the atm328_pins.h file), otherwise corresponding changes may need to be made in in this file before compiling and flashing the firmware.
evoGateway requires the evofw3 arduino firmware by @ghoti57, to decode/encode the radio signals and make the message packets available to/from the ramses_rf framework.
evoGateway is based substantially around the ramses_rf
python framework library written and maintained by David Bonnes (@zxdavb) - https://github.com/zxdavb/ramses_rf, and of course credit to Peter Price (@ghoti57) for his evofw3 firmware for the arduinio, without which none of this would be possible!
(Older pre-version 3 of this script was based on the Domitcz source, specifically the evohomeRadio.cpp
file, by fulltalgoRythm - https://github.com/domoticz/domoticz/blob/development/hardware/evohomeRadio.cpp).
Also see http://www.automatedhome.co.uk/vbulletin/showthread.php?5085-My-HGI80-equivalent-Domoticz-setup-without-HGI80 for info and discussions on homebrew hardware options.
Update 28/08/2019 Added auto-retry for failed sending of commands; added send command status updates to MQTT topic; added custom send commands capability.
Update 25/5/2019 "Sending" functionality added; some refactoring and bug fixes; README updated accordingly.
Update 18/1/2020 Updated README to include HCC80R zone definition
Update 25/2/2020 Added OpenTherm decoding
Update 03/3/2020 Added decoding of controller fault log messages (note device_info
has been changed to fault_log
)
Added support for overriding sent message acknowledgements
Update 06/4/2020 Added support for newer firmwares, such as evofw3, which include RSSI
Update 09/6/2020 BREAKING CHANGE - Migrated to python 3 (as python 2 is EOL)
Update 18/10/2020 Fix "zoneId" error. Merge enhancements by @number42net (MQTT reconnect, UTC datetime)