A fast ISO to CSO compression program for use with PSP and PS2 emulators, which uses multiple algorithms for best compression ratio.
maxcso myfile.iso
Or, drag the iso file into maxcso.exe on Windows.
Get the latest release from the GitHub releases. Use maxcso.exe
on modern systems, and use
maxcso32.exe
on Windows XP and other 32-bit versions of Windows.
maxcso always uses compression level 9. Decompression speed is about the same regardless of level, and disk access is faster with smaller files.
Using 7-zip's deflate and Zopfli improves compression ratios, but don't expect a lot. Usual results are between 0.5% to 1.0% smaller.
Larger block sizes than the default will help compression, in the range of 2-3%. However, the files may not be compatible with some software. For example, PPSSPP versions released after 2014-10-26 will support larger block sizes.
Avoid DAX where CSOs using larger block sizes are supported, since DAX is less efficient.
LZ4 support is mostly for experimentation.
Compared to other tools like ciso and CisoPlus, maxcso can run much faster and achieve the same
compression. Use --fast
to get the fastest compression, which matches level 9 in other tools.
Additionally, if you have better than a dual core processor, maxcso will use all of your cores, and perform even better.
In usage, CSOs typically perform well in all known emulators. Some versions of PSP firmware with support for CSOs have bugs in their CSO support, but this doesn't affect emulators.
Usage: maxcso [--args] input.iso [-o output.cso]
Multiple files may be specified. Inputs can be iso or cso files.
--threads=N Specify N threads for I/O and compression
--quiet Suppress status output
--crc Log CRC32 checksums, ignore output files and methods
--measure Measure compressed size without saving output
--fast Use only basic zlib or lz4 for fastest result
--decompress Write out to raw ISO, decompressing as needed
--block=N Specify a block size (default depends on iso size)
Many readers only support the 2048 size
--format=VER Specify cso version (options: cso1, cso2, zso, dax)
These are experimental, default is cso1
--use-zlib Enable trials with zlib for deflate compression
--use-zopfli Enable trials with Zopfli for deflate compression
--use-7zdeflate Enable trials with 7-zip's deflate compression
--use-lz4 Enable trials with lz4hc for lz4 compression
--use-lz4brute Enable bruteforce trials with lz4hc for lz4 compression
--use-libdeflate Enable trials with libdeflate compression
--only-METHOD Only allow a certain compression method (zlib, etc. above)
--no-METHOD Disable a certain compression method (zlib, etc. above)
The default is to use zlib and 7zdeflate only
--lz4-cost=N Allow lz4 to increase block size by N% at most (cso2 only)
--orig-cost=N Allow uncompressed to increase block size by N% at most
--output-path=X Output to path X/, use basename for default outputs
Because Zopfli is significantly slower than the other methods, and uses a lot more memory, it
is disabled by default. Add --use-zopfli
for maximum compression.
Libdeflate is also disabled by default, because its output is not compatible with some PSP CFW.
When not using PSP CFW, --use-libdeflate
may improve compression a bit.
The cost arguments enable you to allow each block to be N% bigger by using lz4 or no compression. This makes the file read faster (less cpu power), but take more space.
maxcso has been tested on Windows, macOS, and Linux so far. The code was written to be portable. If you'd like to port it to another platform, pull requests are accepted. It may just compile without any changes.
To build on Windows, simply open cli/maxcso.sln and build. Visual Studio 2017 or higher is required.
Aside from gcc/g++ or clang (from Xcode or brew), you will also need:
brew install lz4
brew install libuv
brew install libdeflate
And then just compile using make.
Aside from gcc/g++ or clang, you will also need liblz4-dev, libdeflate-dev, and libuv1-dev - or similar.
The following Dockerfile will produce an Ubuntu image with the needed build dependencies:
FROM ubuntu:latest
RUN apt-get update && apt-get install -y build-essential pkgconf zlib1g-dev liblz4-dev libuv1-dev
Community provided packages are available on some platforms under "maxcso". Please confirm version and security before using. Thanks should go to their respective maintainers.
On Windows, you can use a cmd or batch file to simplify arguments when using drag-and-drop. Create the file in the same directory as maxcso.exe, and then drag files into the batch file.
For example, to maximize compression of PS2 ISO files for use with an emulator, use this:
@echo off
"%~dp0\maxcso.exe" --use-zopfli --block=16384 %*
pause
(--use-zopfli
makes this very slow, but you can try other arguments.)
Similarly, to create CSOs in a "compressed" folder, use this: (create the "compressed" folder next to the batch file.)
@echo off
"%~dp0\maxcso.exe" "--output-path=%~dp0\compressed/" %*
pause
More complex batch scripts can be created, but these are simple to start with. See the examples() folder for some samples to try.
The larger portion of code here is from others' wonderful work in decompression and I/O libraries. Licensing is as follows: