The LinknLink integration allows you to control and monitor LinknLink universal remotes, smart plugs, power strips, switches and sensors. The following devices are supported:

• Sensors: ehub, eTHS, eMotion
• Universal Remotes: eHub

Entities and subdomains

There is no more need to set up platforms except for custom IR/RF switches. Once the device is configured all entities will be created automatically.

The entities have the same name as the device by default. To change the name, icon, or entity id select the entity on the frontend and click the settings icon in the upper right. You can also disable the entity there if you don't think it is useful. Don't forget to select Update to save your changes when you're done.

The entities are divided into four subdomains:

• Remote
• Sensor

Remote

The remote entities allow you to learn and send codes with universal remotes. They are created automatically when you configure devices with IR/RF capabilities.

Learning commands

Use remote.learn_command to learn IR and RF codes. These codes are grouped by device and stored as commands in the storage folder. They can be sent with the remote.send_command service later.

Learning IR codes

To learn IR codes, call remote.learn_command with the device name and command to be learned:

# Example configuration.yaml entry
script:
  learn_tv_power:
    sequence:
      - service: remote.learn_command
        target:
          entity_id: remote.bedroom
        data:
          device: television
          command: power

When the LED blinks, point the remote at the LinknLink device and press the button you want to learn.

After this, you can call remote.send_command with the same data to send the code. You can also access the code in the storage folder to build a custom IR/RF switch or send it with the prefix b64:.

Learning RF codes

Learning RF codes takes place in two steps. First call remote.learn_command with the command_type: rf option:

# Example configuration.yaml entry
script:
  learn_car_unlock:
    sequence:
      - service: remote.learn_command
        target:
          entity_id: remote.garage
        data:
          device: car
          command: unlock
          command_type: rf

When the LED blinks for the first time, press and hold the button to sweep the frequency. Then wait for the LED to blink again and press the button a second time to capture the code.

The codes will be stored in the same way as the IR codes. You don't need to specify command_type to send them because this information is stored in the first byte of the code.

Tip: Select Notifications in the sidebar after calling the service and follow the instructions to make sure you are pressing the button at the right time.

Learning a sequence of commands

In order to streamline the learning process, you may want to provide a list of commands to be learned sequentially:

# Example configuration.yaml entry
script:
  learn_tv_commands:
    sequence:
      - service: remote.learn_command
        target:
          entity_id: remote.bedroom
        data:
          device: television
          command:
            - turn on
            - turn off
            - volume up
            - volume down

After calling this service, you will be prompted to press the buttons in the same order as provided. Check the notifications to stay on track and make sure you are pressing the right button at the right time.

Learning an alternative code

Some protocols require a toggle bit to distinguish one button press from another. In such cases, learning an alternative code will significantly increase the response rate of the device.

The toggle bit is common when a button is used for multiple purposes, such as the power button, which can turn the television on and off, and the volume button, which can be used with a short press or a long press.

If the code works sometimes, and sometimes it doesn't, you can try to relearn it with the alternative: true option:

# Example configuration.yaml entry
script:
  learn_tv_power_button:
    sequence:
      - service: remote.learn_command
        target:
          entity_id: remote.bedroom
        data:
          device: television
          command: power
          alternative: true

When the LED blinks for the first time, press the button you want to learn. Then wait for the LED to blink again and press the same button. This wil cause two different codes will be learned for the same command and they will be sent alternately at each call.

Learned codes storage location

The learned codes are stored in /config/.storage/ in a JSON file called linknlink_remote_MACADDRESS_codes. You can open this file with a text editor and copy the codes to set up custom IR/RF switches or to send them as base64 codes, but beware: the files in the .storage folder should never be edited manually.

Sending commands

After learning IR and RF codes with the remote.learn_command service, you can use remote.send_command to send them. You can also use this service to send base64 codes taken from elsewhere.

Sending a command

To send a command that you've learned, call remote.send_command with the device name and the command to be sent:

# Example configuration.yaml entry
script:
  tv_power:
    sequence:
      - service: remote.send_command
        target:
          entity_id: remote.bedroom
        data:
          device: television
          command: power

Sending a command repeatedly

Use num_repeats: to send the same command multiple times:

# Example configuration.yaml entry
script:
  turn_up_tv_volume_20:
    sequence:
      - service: remote.send_command
        target:
          entity_id: remote.bedroom
        data:
          device: television
          command: volume up
          num_repeats: 20

Sending a sequence of commands

You can provide a list of commands to be sent sequentially:

# Example configuration.yaml entry
script:
  turn_on_ac:
    sequence:
      - service: remote.send_command
        target:
          entity_id: remote.bedroom
        data:
          device: air conditioner
          command:
            - turn on
            - turn off display

Sending a base64 code

Sometimes you may want to send a base64 code obtained elsewhere. Use the b64: prefix for this:

# Example configuration.yaml entry
script:
  turn_on_tv:
    sequence:
      - service: remote.send_command
        target:
          entity_id: remote.bedroom
        data:
          command: b64:JgAcAB0dHB44HhweGx4cHR06HB0cHhwdHB8bHhwADQUAAAAAAAAAAAAAAAA=

Sending a sequence of base64 codes

You can send a sequence of base64 codes just like normal commands:

# Example configuration.yaml entry
script:
  turn_on_ac:
    sequence:
      - service: remote.send_command
        target:
          entity_id: remote.bedroom
        data:
          command:
            - b64:JgAcAB0dHB44HhweGx4cHR06HB0cHhwdHB8bHhwADQUAAAAAAAAAAAAAAAA=
            - b64:JgAaABweOR4bHhwdHB4dHRw6HhsdHR0dOTocAA0FAAAAAAAAAAAAAAAAAAA=

Mixing commands and base64 codes

You can mix commands and base64 codes:

# Example configuration.yaml entry
script:
  turn_on_ac:
    sequence:
      - service: remote.send_command
        target:
          entity_id: remote.bedroom
        data:
          device: television
          command:
            - turn on
            - b64:JgAaABweOR4bHhwdHB4dHRw6HhsdHR0dOTocAA0FAAAAAAAAAAAAAAAAAAA=

Deleting commands

You can use remote.delete_command to remove commands that you've learned with the remote.learn_command service.

Deleting a command

To delete a command, call remote.delete_command with the device name and the command to be deleted:

# Example configuration.yaml entry
script:
  delete_tv_power:
    sequence:
      - service: remote.delete_command
        target:
          entity_id: remote.bedroom
        data:
          device: television
          command: power

Deleting multiple commands

You can provide a list of commands to be deleted:

# Example configuration.yaml entry
script:
  delete_tv_commands:
    sequence:
      - service: remote.delete_command
        target:
          entity_id: remote.bedroom
        data:
          device: television
          command:
            - power
            - source
            - menu

Sensor

The sensor entities allow you to monitor LinknLink sensors. These entities are created automatically when you configure a device that has sensors.