bdring FluidNC issues - Githubissues

bdring / FluidNC

The next generation of motion control firmware

Other

1.62k stars 386 forks source link

issues

Newest

Newest Most commented Recently updated Oldest Least commented Least recently updated

Encode + in WebUI commands so it doesn't get lost

#1383 MitchBradley opened 1 day ago
0
Problem: The FluidNC stuck at saving after filled WiFi credential

#1382 notusenn closed 3 days ago
11
Fix selected tool param

#1381 bdring closed 4 days ago
1
Problem: Spindle starts at tool change location, for 1st tool change only.

#1380 ikhwan-ma closed 18 hours ago
8
Problem: Incorrect I2S BCK signal on v3.9.1

#1379 MrTransistorsChannel closed 1 week ago
8
Problem: Pulloff_mm not added to Machine Position after homing

#1378 Quintenluyten closed 1 week ago
3
Alarms no longer force idle

#1377 bdring closed 1 week ago
0
Feature: Blow chips off the top of TLO sensor during probing offsets, between tool changes.

#1376 ikhwan-ma opened 1 week ago
2
Problem: Spindle stop for tool change, while still in motion, before operation completes.

#1375 ikhwan-ma closed 1 week ago
11
Adjust M6 macro behaviour

#1374 rvalotta closed 1 week ago
0
Feature: Updated to M6 Macro behavior

#1373 rvalotta closed 1 week ago
4
Problem: G93 timing inaccurate

#1372 AndreasEpp opened 2 weeks ago
2
Possibility to impose a speed different from the maximum speed of the translation movement in G0 movements

#1371 Deltaplc closed 2 weeks ago
19
Improve web request handling

#1370 michmela44 closed 2 weeks ago
0
Feature: software axis skewness compensation

#1369 stez90 opened 2 weeks ago
3
Problem: Run Macro $X when Alarm

#1368 agoy507 opened 2 weeks ago
0
Undo UART looping changes for now

#1367 MitchBradley closed 3 weeks ago
0
Dymk/refactor run fixtures

#1366 MitchBradley closed 1 week ago
0
Revert "Allow rewinding of commands sent via UART buffer"

#1365 MitchBradley closed 3 weeks ago
0
Problem: v3.9.0 Homing issues

#1364 mattydboom closed 3 weeks ago
7
Problem: 3.9.0 Start a file causes reboot.

#1363 V1EngineeringInc closed 3 weeks ago
11
Feature: link 2 identical cnc controllers so we can drive more motors

#1362 aguaviva opened 3 weeks ago
5
When using expressions to create a macro, expressions using "and" or 'or" logic are returning an error

#1361 rvalotta closed 3 weeks ago
6
Problem: job running from SD stalls if wifi conection is lost

#1360 Ams-Laser opened 3 weeks ago
3
Problem: Unable to move any axis - Motor leds stay off

#1359 gbooysen opened 4 weeks ago
3
Problem: Works perfectly in open-loop, misses steps in closed loop

#1358 Nicknico69 closed 4 weeks ago
7
Feature: Setting step_per_mm paramater for each Y motor individually.

#1357 Simon5162 opened 1 month ago
2
Problem: fluidnc v3.8.3 crashing while executing gcode file from local storage

#1356 AndreasEpp closed 1 month ago
1
Problem: Z axis inverted with 3.8.3 pre3 and :high / :low makes no difference

#1355 rvalotta closed 1 month ago
6
Problem: Steppers not moving

#1354 SpikZASA closed 1 month ago
3
Problem: How to restart wifi after settings

#1353 zengfanfan closed 1 month ago
3
Feature: gcode clustering support for faster engraving

#1352 Ams-Laser opened 1 month ago
23
Problem: Jerky / Pulsing / Uneven Movement.

#1351 tomgale closed 1 month ago
13
Problem: M6 Macro is reporting the same value for _current_tool, _selected_tool and #5400

#1350 rvalotta opened 1 month ago
6
Stepping without using class vtables

#1349 MitchBradley closed 3 weeks ago
0
Problem: LY620-A RS485

#1348 qulet opened 1 month ago
0
Problem: steppers not moving

#1347 LogrythmAtGmailDotCom closed 1 month ago
39
Allow rewinding of commands sent via UART buffer

#1346 dymk closed 1 month ago
0
Allow rewinding of commands sent via UART buffer

#1345 dymk closed 1 month ago
7
Problem: Midtbod/HBot axes calibration.

#1344 Kenabi31 opened 1 month ago
0
Refactor run_fixture tool, clean up ops

#1343 dymk closed 1 month ago
0
Edit yaml file with website

#1342 FMD14 opened 1 month ago
4
Problem: How to configure 6x CNC Controller for FluidNC for a Y axis with two stepper motors and ball screw drives.

#1341 MrMagoo-lab opened 1 month ago
1
Problem: TMC5160 with MKS DLC32 V2.1

#1340 Kenabi31 closed 1 month ago
4
Problem: Homin issue on CoreXY

#1339 Kenabi31 opened 1 month ago
3
Skip leading whitespace when processing dollar commands

#1338 dymk closed 1 month ago
0
Fix WebUI v3 ESP800 values

#1337 michmela44 closed 2 weeks ago
0
Fix for invalid control characters appearing in JSON causing the About dialog in WebUI v3 to not load

#1336 michmela44 closed 1 month ago
0
Fix repeat of 0, O commands with larger integer values

#1335 dymk closed 1 month ago
0
Fix #1295 - Crash when reloading WebUI while running

#1334 MitchBradley closed 1 month ago
0